Design your own

10×16 Gable Shed Plans on a Slab

This 10×16 gable shed sits on a 4″ concrete slab, with 8′ walls, a 6/12 gable roof and a peak of 10′ 10-7/8″. The 64″-wide double door opening gets a doubled header sized for the roof load above it. Rafters are 2x4 at 16″ on center. All 126 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 102 boards plus sheet goods and hardware.

Footprint10′ 0″ × 16′ 0″
Area160 sq ft
Height10′ 10-7/8″
Lumber126 pcs
Steps12
Checks8 pass

Open in the builderJump to the steps

3D model of the 10×16 gable shed framing

Shopping list

742x4 × 8′
42x4 × 10′
112x4 × 12′
42x4 × 16′
32x6 × 8′
12x6 × 20′
2PT 2x4 × 8′
2PT 2x4 × 10′
1PT 2x4 × 16′
167/16" OSB wall sheathing, 4×8 (10% waste)
81/2" OSB roof sheathing, 4×8 (15% waste)
8bundles shingles (2.1 squares + 10%)
1rolls synthetic underlayment
2.29cubic yards concrete (+10%)
26hurricane ties, rafter to plate

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A22x667"Header plysquare; two plies with a 1/2" plywood spacer
B12x4188-1/2"Top platesquare ends; laps the next piece at the corner
C82x492-5/8"Studsquare both ends
D22x492-5/8"King studsquare both ends
E22x476-1/2"Jack studsquare both ends
F1PT 2x464"Bottom platesquare ends; laps the next piece at the corner
G1PT 2x460-1/2"Bottom platesquare ends; laps the next piece at the corner
H52x410-5/8"Cripplesquare both ends
J1PT 2x4116-1/2"Bottom platesquare ends; laps the next piece at the corner
K12x4116-1/2"Top platesquare ends; laps the next piece at the corner
L92x492-5/8"Studsquare both ends
M1PT 2x4188-1/2"Bottom platesquare ends; laps the next piece at the corner
N12x4188-1/2"Top platesquare ends; laps the next piece at the corner
P132x492-5/8"Studsquare both ends
Q22x633-1/2"Header plysquare; two plies with a 1/2" plywood spacer
R1PT 2x4116-1/2"Bottom platesquare ends; laps the next piece at the corner
S12x4116-1/2"Top platesquare ends; laps the next piece at the corner
T72x492-5/8"Studsquare both ends
U22x492-5/8"King studsquare both ends
V22x469"Jack studsquare both ends
W42x441"Cripplesquare both ends
X12x430-1/2"Rough sillsquare both ends
Y22x418-1/8"Cripplesquare both ends
Z22x4188-1/2"Cap platelaps over the next wall at the corner
AA22x4116-1/2"Cap platelaps over the next wall at the corner
AB12x6192"Ridge boardsquare both ends
AC262x481-7/16"Common rafterplumb cut 6/12 at the ridge; birdsmouth seat 1-1/2", heel 3/4"; tail plumb cut 12" past the wall
AD112x4120"Rafter tietop corners cut to 6/12
AE22x427-5/8"Gable studtop cut 6/12 (26.6°), long point up
AF22x423-5/8"Gable studtop cut 6/12 (26.6°), long point up
AG22x419-5/8"Gable studtop cut 6/12 (26.6°), long point up
AH22x415-5/8"Gable studtop cut 6/12 (26.6°), long point up
AJ22x411-5/8"Gable studtop cut 6/12 (26.6°), long point up
AK22x47-5/8"Gable studtop cut 6/12 (26.6°), long point up
AL22x43-5/8"Gable studtop cut 6/12 (26.6°), long point up

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Pour the slab

    Pour the slab

    • Form, gravel, pour a 4" slab with a thickened edge.
    • Anchor bolts 6" from every plate end and every 6 ft.

    floatlevel

  2. Step 2: Build the front wall

    Build the front wall

    A ×2 2x6 67"B ×1 2x4 188-1/2"C ×8 2x4 92-5/8"D ×2 2x4 92-5/8"E ×2 2x4 76-1/2"F ×1 2x4 64"G ×1 2x4 60-1/2"H ×5 2x4 10-5/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 127-1/4" · 143-1/4" · 159-1/4" · 175-1/4" · 187"
    • Frame the 64" × 78" door: kings, jacks, header.
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  3. Step 3: Build the right wall

    Build the right wall

    J ×1 2x4 116-1/2"K ×1 2x4 116-1/2"L ×9 2x4 92-5/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 115"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  4. Step 4: Build the back wall

    Build the back wall

    M ×1 2x4 188-1/2"N ×1 2x4 188-1/2"P ×13 2x4 92-5/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 127-1/4" · 143-1/4" · 159-1/4" · 175-1/4" · 187"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  5. Step 5: Build the left wall

    Build the left wall

    Q ×2 2x6 33-1/2"R ×1 2x4 116-1/2"S ×1 2x4 116-1/2"T ×7 2x4 92-5/8"U ×2 2x4 92-5/8"V ×2 2x4 69"W ×4 2x4 41"X ×1 2x4 30-1/2"Y ×2 2x4 18-1/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 115"
    • Frame the 30-1/2" × 26-1/2" window: kings, jacks, header.
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  6. Step 6: Lap the cap plates

    Lap the cap plates

    Z ×2 2x4 188-1/2"AA ×2 2x4 116-1/2"

    • Cap plates overlap every corner. That ties the walls into one box.
    • Nails every 16", two at each lap.

    hammer

  7. Step 7: Raise the ridge

    Raise the ridge

    AB ×1 2x6 192"

    • Ridge AB on temporary posts at the height shown.
    • Plumb and brace before any rafters.

    levelclamps

  8. Step 8: Set the rafters

    Set the rafters

    AC ×26 2x4 81-7/16"

    • Cut ONE pattern rafter. Check it in three places. Then cut the rest.
    • Every 16", over the studs.
    • Hurricane tie every rafter to the plate.

    speed squaresawdrill

  9. Step 9: Tie the rafters

    Tie the rafters

    AD ×11 2x4 120"

    • A tie beside every rafter pair, on the cap plates.
    • Nail each end to its rafter.

    hammer

  10. Step 10: Fill the gable ends

    Fill the gable ends

    AE ×2 2x4 27-5/8"AF ×2 2x4 23-5/8"AG ×2 2x4 19-5/8"AH ×2 2x4 15-5/8"AJ ×2 2x4 11-5/8"AK ×2 2x4 7-5/8"AL ×2 2x4 3-5/8"

    • Studs every 16" from the cap up to the rafter.
    • Measure each in place. Long point up.

    speed squaresaw

  11. Step 11: Sheath the walls

    Sheath the walls

    • Sheets vertical, edges on studs, 1/8" gaps.
    • Nails 6" on edges, 12" in the middle. Cut out the openings after.

    sawnailerchalk line

  12. Step 12: Sheath the roof

    Sheath the roof

    • Long edge across the rafters, H-clips between, rows staggered.
    • Drip edge, underlayment, drip edge, shingles.

    sawnailer

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 132 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 133 pieces trace a chain of contact down to the foundation.
✓ Rafters 2x4 30% used
2x4 SPF #2, span 4.94 ft, w = 43 plf total / 28 plf live
Bending: M = wL²/8 = 1569 in·lb → fb = M/S = 512 psi ≤ F'b = 1736 psi  (30% used)
Shear: fv = 1.5V/A = 30 psi ≤ F'v = 155 psi  (19% used)
Deflection: 5wL⁴/384EI = 0.050" ≤ L/240 = 0.247"  (20% used)
✓ Header over door (front) 2x6 46% used
2-ply 2x6 SPF #2, span 5.58 ft, w = 193 plf total / 126 plf live
Bending: M = wL²/8 = 9029 in·lb → fb = M/S = 597 psi ≤ F'b = 1308 psi  (46% used)
Shear: fv = 1.5V/A = 49 psi ≤ F'v = 155 psi  (32% used)
Deflection: 5wL⁴/384EI = 0.047" ≤ L/240 = 0.279"  (17% used)
✓ Studs (front wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 257 lb  (9% used)
✓ Studs (back wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 257 lb  (9% used)
✓ Header over window (left) 2x6 0% used
2-ply 2x6 SPF #2, span 2.79 ft, w = 6 plf total / 4 plf live
Bending: M = wL²/8 = 70 in·lb → fb = M/S = 5 psi ≤ F'b = 1308 psi  (0% used)
Shear: fv = 1.5V/A = 1 psi ≤ F'v = 155 psi  (0% used)
Deflection: 5wL⁴/384EI = 0.000" ≤ L/240 = 0.140"  (0% used)
✓ Birdsmouth notch shear (rafters) 2x4 45% used
Heel cut 3/4" plumb leaves dn = 2.83" of the 3.5" depth over the bearing.
NDS 3.4.3.2 notched end: V'r = 2/3 · F'v · b · dn · (dn/d)² = 287 lb ≥ reaction 129 lb (45% used)

Roof: 10 psf dead + snow 0.7 × 30 = 21 psf. Rafter ties at every rafter pair stop the walls spreading (a ridge board is not a beam). Nail per IRC Table R802.5.2.

Questions

How much lumber does a 10x16 Gable Shed need?

74 2x4 × 8′, 4 2x4 × 10′, 11 2x4 × 12′, 4 2x4 × 16′, 3 2x6 × 8′, 1 2x6 × 20′, 2 PT 2x4 × 8′, 2 PT 2x4 × 10′, 1 PT 2x4 × 16′. 16 7/16" OSB wall sheathing, 4×8 (10% waste); 8 1/2" OSB roof sheathing, 4×8 (15% waste); 8 bundles shingles (2.1 squares + 10%).

What size rafters does a 10x16 Gable Shed need?

2x4 at 16″ on center, using 30% of their capacity at 30 psf ground snow. The bending, shear and deflection numbers are in the proof section.

How tall is it?

10′ 10-7/8″ at the peak, measured from the ground.

Do I need a permit for a 10x16 Gable Shed?

It covers 160 sq ft. The model code (IRC R105.2) exempts one-story detached accessory buildings up to 200 sq ft, and many towns set the line at 120 sq ft. Call your building department before you dig.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

8×20 Gable Shed160 sq ft · 154 pcs · 14 steps8×20 Gable Shed160 sq ft · 132 pcs · 12 steps10×16 Gable Shed160 sq ft · 145 pcs · 14 steps12×14 Gable Shed168 sq ft · 143 pcs · 14 steps12×14 Gable Shed168 sq ft · 125 pcs · 12 steps12×12 Gable Shed144 sq ft · 131 pcs · 14 steps