Design your own

12×20 Deck Plans, 36″ High

This 12′ × 20′ deck stands 36″ off the ground on posts on concrete footings. Joists are 2x8 at 16″ on center, carried by doubled 2x10 beams. The stairs and the 36″ guard are drawn and checked. All 259 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 164 boards plus sheet goods and hardware.

Footprint12′ 0″ × 20′ 0″
Area240 sq ft
Height6′ 0″
Lumber259 pcs
Steps7
Checks9 pass

Open in the builderJump to the steps

3D model of the 12×20 deck framing

Shopping list

4PT 2x10 × 20′
5PT 2x12 × 8′
39PT 2x2 × 8′
20PT 2x4 × 8′
10PT 2x6 × 8′
2PT 2x6 × 14′
1PT 2x6 × 20′
18PT 2x8 × 12′
2PT 2x8 × 20′
11PT 4x4 × 8′
26PT 5/4x6 × 10′
26PT 5/4x6 × 14′
1.01cubic yards concrete (+10%)
8post bases + post caps
2boxes 2-1/2" deck screws (350/box)

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A8PT 4x418-1/2"Postsquare both ends
B4PT 2x10232"Beam plysquare; 2 plies nailed together, 10d every 16" staggered
C2PT 2x8238-1/2"Rim joistsquare ends; laps the next piece at the corner
D2PT 2x8142-1/2"Rim joistsquare ends; laps the next piece at the corner
E16PT 2x8141"Floor joistsquare both ends
F26PT 5/4x6143-15/16"Deck boardsquare both ends
G26PT 5/4x695-15/16"Deck boardsquare both ends
H1PT 2x6240"Rail capflat on the post tops; mitred at corners
J2PT 2x6144"Rail capflat on the post tops; mitred at corners
K2PT 2x692-1/2"Rail capflat on the post tops; mitred at corners
L4PT 2x466-3/4"Bottom railsquare both ends
M4PT 2x466-3/4"Top railsquare both ends
N4PT 2x455-5/8"Bottom railsquare both ends
P4PT 2x455-5/8"Top railsquare both ends
Q4PT 2x441"Bottom railsquare both ends
R4PT 2x441"Top railsquare both ends
S17PT 4x442-3/4"Guard postsquare; through-bolt to the rim, two 1/2" bolts
T116PT 2x224"Balustersquare both ends
U4PT 2x1249-1/4"Stair stringer4 notches: rise 7-3/16", run 10-1/4"; plumb cut at the top, level cut at the bottom
V1PT 2x1248"Stair hanger boardsquare; bolt to the rim
W8PT 2x648"Stair treadsquare both ends

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Dig and pour the footings

    Dig and pour the footings

    • Stake out 8 post spots exactly where the picture shows.
    • Dig each hole Ø24" wide, below your frost line.
    • Pour concrete. Set a post base in each one, all level with a string line.

    shovelstring linelevel

  2. Step 2: Stand the posts

    Stand the posts

    A ×8 4x4 18-1/2"

    • Cut posts A to the length in the box.
    • Fix each to its base. Plumb on two faces. Brace both ways.

    sawleveldrill

  3. Step 3: Set the beams

    Set the beams

    B ×4 2x10 232"

    • Nail each pair of B plies together, 10d nails every 16", staggered.
    • Crown up. Set on the posts and fix with post caps.

    sawhammerlevel

  4. Step 4: Frame the floor

    Frame the floor

    C ×2 2x8 238-1/2"D ×2 2x8 142-1/2"E ×16 2x8 141"

    • Rims C, D around the outside, corners lapped as drawn.
    • Mark joists every 16" along the rims.
    • Joists E between the rims: 3 nails each end.
    • Measure both diagonals. Equal = square.

    sawhammersquaretape

  5. Step 5: Lay the decking

    Lay the decking

    F ×26 5/4x6 143-15/16"G ×26 5/4x6 95-15/16"

    • Start at the front edge. 1/8" gap between boards (a 16d nail).
    • Two screws into every joist. Board ends only land on a joist.

    drillsawchalk line

  6. Step 6: Add the railing

    Add the railing

    H ×1 2x6 240"J ×2 2x6 144"K ×2 2x6 92-1/2"L ×4 2x4 66-3/4"M ×4 2x4 66-3/4"N ×4 2x4 55-5/8"P ×4 2x4 55-5/8"Q ×4 2x4 41"R ×4 2x4 41"S ×17 4x4 42-3/4"T ×116 2x2 24"

    • Posts first. Then bottom and top rails.
    • Balusters with a 3-7/8" spacer block between each.
    • Cap last.

    drillsawlevel

  7. Step 7: Build the stairs

    Build the stairs

    U ×4 2x12 49-1/4"V ×1 2x12 48"W ×8 2x6 48"

    • Bolt the hanger board to the rim.
    • Lay out ONE stringer with a framing square. Test it. Cut the rest.
    • Stringers on the pad. Two screws per tread board per stringer.

    framing squaresawdrill

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 259 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 268 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x8 60% used
2x8 SPF #2, span 9.75 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 9506 in·lb → fb = M/S = 723 psi ≤ F'b = 1208 psi  (60% used)
Shear: fv = 1.5V/A = 45 psi ≤ F'v = 135 psi  (33% used)
Deflection: 5wL⁴/384EI = 0.163" ≤ L/360 = 0.325"  (50% used)
✓ Deck beams (2-ply) 2x10 79% used
2-ply 2x10 SPF #2, span 6.35 ft, w = 538 plf total / 430 plf live
Bending: M = wL²/8 = 32482 in·lb → fb = M/S = 759 psi ≤ F'b = 963 psi  (79% used)
Shear: fv = 1.5V/A = 92 psi ≤ F'v = 135 psi  (68% used)
Deflection: 5wL⁴/384EI = 0.057" ≤ L/360 = 0.212"  (27% used)
✓ Floor posts 4x4 21% used
4x4 SPF #2, height 1.54 ft, le/d = 5.3 ≤ 50
FcE = 15005 psi → Cp = 0.981 → capacity 15900 lb ≥ load 3412 lb (21% used)
✓ Footings 76% used
Load 3562 lb ÷ 1500 psf presumptive soil bearing = 342 in² needed
24" round footing = 452 in² (76% used). Bottom below your local frost depth.
✓ Guard geometry 90% used
36" guard height. Baluster gaps under 4", so a 4" ball cannot pass. Bottom gap 3-1/2".
Guard-post bolting follows the AWC DCA 6 detail; that connection is not calculated here.
✓ Stair geometry 93% used
5 equal risers of 7-3/16" (max 7-3/4"), 4 treads: 10-1/4" run + 1" nosing (min 10").
Notched 2x12 stringers keep 5-3/8" of wood under each notch (min 5").
✓ Stair stringers 19% used
2x12 (5.36" deep after notching) SPF #2, span 3.42 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 1167 in·lb → fb = M/S = 163 psi ≤ F'b = 875 psi  (19% used)
Shear: fv = 1.5V/A = 21 psi ≤ F'v = 135 psi  (16% used)
Deflection: 5wL⁴/384EI = 0.006" ≤ L/360 = 0.114"  (5% used)

Floor: 40 psf live + 10 psf dead. Footings bear on undisturbed soil below frost depth (1500 psf soil assumed). Post bases and post caps at every post.

Questions

How much lumber does a 12x20 Deck need?

4 PT 2x10 × 20′, 5 PT 2x12 × 8′, 39 PT 2x2 × 8′, 20 PT 2x4 × 8′, 10 PT 2x6 × 8′, 2 PT 2x6 × 14′, 1 PT 2x6 × 20′, 18 PT 2x8 × 12′, 2 PT 2x8 × 20′, 11 PT 4x4 × 8′, 26 PT 5/4x6 × 10′, 26 PT 5/4x6 × 14′. 1.01 cubic yards concrete (+10%); 8 post bases + post caps; 2 boxes 2-1/2" deck screws (350/box).

What size joists does a 12x20 Deck need?

2x8 at 16″ on center, using 60% of capacity at 40 psf live load.

How big do the footings need to be?

24″ round, 8 of them, bearing below your local frost line. That assumes 1,500 psf soil.

Does a 12x20 Deck need a railing?

Yes. Any deck surface more than 30″ above grade needs a guard at least 36″ high, and this plan includes one.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

12×20 Deck240 sq ft · 95 pcs · 6 steps12×20 Deck240 sq ft · 263 pcs · 7 steps12×20 Ground-Level Deck240 sq ft · 74 pcs · 3 steps14×16 Deck224 sq ft · 98 pcs · 6 steps14×16 Deck224 sq ft · 252 pcs · 7 steps14×16 Deck224 sq ft · 256 pcs · 7 steps