Design your own

20×20 Ground-Level Deck Plans

This 20′ × 20′ deck stands at ground level on skids. Joists are 2x8 at 16″ on center, resting on the skids. All 109 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 109 boards plus sheet goods and hardware.

Footprint20′ 0″ × 20′ 0″
Area400 sq ft
Height1′ 1-3/4″
Lumber109 pcs
Steps3
Checks3 pass

Open in the builderJump to the steps

3D model of the 20×20 ground-level deck framing

Shopping list

20PT 2x8 × 20′
3PT 4x6 × 20′
43PT 5/4x6 × 10′
43PT 5/4x6 × 14′
3boxes 2-1/2" deck screws (350/box)

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A3PT 4x6240"Skidsquare both ends
B4PT 2x8238-1/2"Rim joistsquare ends; laps the next piece at the corner
C16PT 2x8237"Floor joistsquare both ends
D43PT 5/4x6143-15/16"Deck boardsquare both ends
E43PT 5/4x695-15/16"Deck boardsquare both ends

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Lay the skids

    Lay the skids

    A ×3 4x6 240"

    • Compact 4" of gravel 2 ft past the footprint.
    • Lay A parallel, level within 1/4".

    rakelevel

  2. Step 2: Frame the floor

    Frame the floor

    B ×4 2x8 238-1/2"C ×16 2x8 237"

    • Rims B around the outside, corners lapped as drawn.
    • Mark joists every 16" along the rims.
    • Joists C between the rims: 3 nails each end.
    • Measure both diagonals. Equal = square.

    sawhammersquaretape

  3. Step 3: Lay the decking

    Lay the decking

    D ×43 5/4x6 143-15/16"E ×43 5/4x6 95-15/16"

    • Start at the front edge. 1/8" gap between boards (a 16d nail).
    • Two screws into every joist. Board ends only land on a joist.

    drillsawchalk line

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 109 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 109 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x8 61% used
2x8 SPF #2, span 9.85 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 9710 in·lb → fb = M/S = 739 psi ≤ F'b = 1208 psi  (61% used)
Shear: fv = 1.5V/A = 45 psi ≤ F'v = 135 psi  (34% used)
Deflection: 5wL⁴/384EI = 0.170" ≤ L/360 = 0.328"  (52% used)

Floor: 40 psf live + 10 psf dead. 3 skids on 4" of compacted gravel, level within 1/4".

Questions

How much lumber does a 20x20 Ground-Level Deck need?

20 PT 2x8 × 20′, 3 PT 4x6 × 20′, 43 PT 5/4x6 × 10′, 43 PT 5/4x6 × 14′. 3 boxes 2-1/2" deck screws (350/box).

What size joists does a 20x20 Ground-Level Deck need?

2x8 at 16″ on center, using 61% of capacity at 40 psf live load.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

20×20 Deck400 sq ft · 135 pcs · 6 steps20×20 Deck400 sq ft · 343 pcs · 7 steps20×20 Deck400 sq ft · 347 pcs · 7 steps16×20 Deck320 sq ft · 113 pcs · 6 steps16×20 Deck320 sq ft · 301 pcs · 7 steps16×20 Deck320 sq ft · 305 pcs · 7 steps