Design your own

4×6 Lean-To Shed Plans

This 4×6 lean-to shed sits on pressure-treated skids on gravel, with 8′ walls, a 3/12 single-slope roof and a peak of 10′ 7-5/8″. The 34″-wide door opening gets a doubled header sized for the roof load above it. Rafters are 2x4 at 16″ on center. All 62 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 44 boards plus sheet goods and hardware.

Footprint4′ 0″ × 6′ 0″
Area24 sq ft
Height10′ 7-5/8″
Lumber62 pcs
Steps12
Checks8 pass

Open in the builderJump to the steps

3D model of the 4×6 lean-to shed framing

Shopping list

292x4 × 8′
62x4 × 10′
12x6 × 8′
6PT 2x6 × 8′
2PT 4x6 × 8′
13/4" T&G plywood subfloor, 4×8
77/16" OSB wall sheathing, 4×8 (10% waste)
21/2" OSB roof sheathing, 4×8 (15% waste)
2bundles shingles (0.4 squares + 10%)
1rolls synthetic underlayment
6hurricane ties, rafter to plate

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A2PT 4x672"Skidsquare both ends
B2PT 2x670-1/2"Rim joistsquare ends; laps the next piece at the corner
C2PT 2x646-1/2"Rim joistsquare ends; laps the next piece at the corner
D6PT 2x645"Floor joistsquare both ends
E22x637"Header plysquare; two plies with a 1/2" plywood spacer
F32x492-5/8"Studsquare both ends
G22x492-5/8"King studsquare both ends
H22x476-1/2"Jack studsquare both ends
J12x468-1/2"Top platesquare ends; laps the next piece at the corner
K12x419"Bottom platesquare ends; laps the next piece at the corner
L12x415-1/2"Bottom platesquare ends; laps the next piece at the corner
M22x410-5/8"Cripplesquare both ends
N42x492-5/8"Studsquare both ends
P12x444-1/2"Bottom platesquare ends; laps the next piece at the corner
Q12x444-1/2"Top platesquare ends; laps the next piece at the corner
R62x4103-3/4"Studsquare both ends
S12x472"Bottom platesquare ends; laps the next piece at the corner
T12x472"Top platesquare ends; laps the next piece at the corner
U42x492-5/8"Studsquare both ends
V12x441"Bottom platesquare ends; laps the next piece at the corner
W12x441"Top platesquare ends; laps the next piece at the corner
X12x472"Cap platelaps over the next wall at the corner
Y12x468-1/2"Cap platelaps over the next wall at the corner
Z12x444-1/2"Cap platelaps over the next wall at the corner
AA12x441"Cap platelaps over the next wall at the corner
AB62x475-1/16"Common rafterplumb cuts 3/12 at both tails; birdsmouth seat 1-1/2", heel 3/8"; tail plumb cut 12" past the wall
AC22x410-3/4"Rake studtop cut 3/12 (14.0°), long point up
AD22x47-13/16"Rake studtop cut 3/12 (14.0°), long point up
AE22x43-13/16"Rake studtop cut 3/12 (14.0°), long point up

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Lay the skids

    Lay the skids

    A ×2 4x6 72"

    • Compact 4" of gravel 2 ft past the footprint.
    • Lay A parallel, level within 1/4".

    rakelevel

  2. Step 2: Frame the floor

    Frame the floor

    B ×2 2x6 70-1/2"C ×2 2x6 46-1/2"D ×6 2x6 45"

    • Rims B, C around the outside, corners lapped as drawn.
    • Mark joists every 16" along the rims.
    • Joists D between the rims: 3 nails each end.
    • Measure both diagonals. Equal = square.

    sawhammersquaretape

  3. Step 3: Lay the subfloor

    Lay the subfloor

    • Long edge across the joists, rows staggered 4 ft.
    • Glue on every joist. Screws 6" on edges, 12" in the middle.

    drillsawchalk line

  4. Step 4: Build the front wall

    Build the front wall

    E ×2 2x6 37"F ×3 2x4 92-5/8"G ×2 2x4 92-5/8"H ×2 2x4 76-1/2"J ×1 2x4 68-1/2"K ×1 2x4 19"L ×1 2x4 15-1/2"M ×2 2x4 10-5/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 67"
    • Frame the 34" × 78" door: kings, jacks, header.
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  5. Step 5: Build the right wall

    Build the right wall

    N ×4 2x4 92-5/8"P ×1 2x4 44-1/2"Q ×1 2x4 44-1/2"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 43"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  6. Step 6: Build the back wall

    Build the back wall

    R ×6 2x4 103-3/4"S ×1 2x4 72"T ×1 2x4 72"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 70-1/2"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  7. Step 7: Build the left wall

    Build the left wall

    U ×4 2x4 92-5/8"V ×1 2x4 41"W ×1 2x4 41"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 3-1/2" · 15-1/4" · 31-1/4" · 43"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  8. Step 8: Lap the cap plates

    Lap the cap plates

    X ×1 2x4 72"Y ×1 2x4 68-1/2"Z ×1 2x4 44-1/2"AA ×1 2x4 41"

    • Cap plates overlap every corner. That ties the walls into one box.
    • Nails every 16", two at each lap.

    hammer

  9. Step 9: Set the rafters

    Set the rafters

    AB ×6 2x4 75-1/16"

    • Cut ONE pattern rafter. Check it in three places. Then cut the rest.
    • Every 16", over the studs.
    • Hurricane tie every rafter to the plate.

    speed squaresawdrill

  10. Step 10: Fill the end walls

    Fill the end walls

    AC ×2 2x4 10-3/4"AD ×2 2x4 7-13/16"AE ×2 2x4 3-13/16"

    • Studs every 16" from the cap up to the rafter.
    • Measure each in place. Long point up.

    speed squaresaw

  11. Step 11: Sheath the walls

    Sheath the walls

    • Sheets vertical, edges on studs, 1/8" gaps.
    • Nails 6" on edges, 12" in the middle. Cut out the openings after.

    sawnailerchalk line

  12. Step 12: Sheath the roof

    Sheath the roof

    • Long edge across the rafters, H-clips between, rows staggered.
    • Drip edge, underlayment, drip edge, shingles.

    sawnailer

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 68 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 68 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x6 17% used
2x6 SPF #2, span 3.71 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 1375 in·lb → fb = M/S = 182 psi ≤ F'b = 1308 psi  (14% used)
Shear: fv = 1.5V/A = 22 psi ≤ F'v = 135 psi  (17% used)
Deflection: 5wL⁴/384EI = 0.008" ≤ L/360 = 0.124"  (6% used)
✓ Rafters 2x4 16% used
2x4 SPF #2, span 3.71 ft, w = 42 plf total / 28 plf live
Bending: M = wL²/8 = 861 in·lb → fb = M/S = 281 psi ≤ F'b = 1736 psi  (16% used)
Shear: fv = 1.5V/A = 22 psi ≤ F'v = 155 psi  (14% used)
Deflection: 5wL⁴/384EI = 0.016" ≤ L/240 = 0.185"  (9% used)
✓ Header over door (front) 2x6 8% used
2-ply 2x6 SPF #2, span 3.08 ft, w = 94 plf total / 63 plf live
Bending: M = wL²/8 = 1339 in·lb → fb = M/S = 89 psi ≤ F'b = 1308 psi  (7% used)
Shear: fv = 1.5V/A = 13 psi ≤ F'v = 155 psi  (8% used)
Deflection: 5wL⁴/384EI = 0.002" ≤ L/240 = 0.154"  (1% used)
✓ Studs (front wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 125 lb  (4% used)
✓ Studs (back wall) 59% used
2x4 SPF #2, unbraced length 103.8" (le/d = 29.6 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 477 psi → Cp = 0.290
Capacity = Cp·F*c·A = 2316 lb ≥ load 125 lb  (5% used)
✓ Birdsmouth notch shear (rafters) 2x4 32% used
Heel cut 3/8" plumb leaves dn = 3.14" of the 3.5" depth over the bearing.
NDS 3.4.3.2 notched end: V'r = 2/3 · F'v · b · dn · (dn/d)² = 391 lb ≥ reaction 125 lb (32% used)

Roof: 10 psf dead + snow 0.7 × 30 = 21 psf. Floor: 40 psf live + 10 psf dead. 2 skids on 4" of compacted gravel, level within 1/4".

Questions

How much lumber does a 4x6 Lean-To Shed need?

29 2x4 × 8′, 6 2x4 × 10′, 1 2x6 × 8′, 6 PT 2x6 × 8′, 2 PT 4x6 × 8′. 1 3/4" T&G plywood subfloor, 4×8; 7 7/16" OSB wall sheathing, 4×8 (10% waste); 2 1/2" OSB roof sheathing, 4×8 (15% waste).

What size rafters does a 4x6 Lean-To Shed need?

2x4 at 16″ on center, using 16% of their capacity at 30 psf ground snow. The bending, shear and deflection numbers are in the proof section.

What size joists does a 4x6 Lean-To Shed need?

2x6 at 16″ on center, using 17% of capacity at 40 psf live load.

How tall is it?

10′ 7-5/8″ at the peak, measured from the ground.

Do I need a permit for a 4x6 Lean-To Shed?

It covers 24 sq ft. The model code (IRC R105.2) exempts one-story detached accessory buildings up to 200 sq ft, and many towns set the line at 120 sq ft. Call your building department before you dig.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

4×8 Lean-To Shed32 sq ft · 67 pcs · 12 steps6×6 Lean-To Shed36 sq ft · 69 pcs · 12 steps4×10 Lean-To Shed40 sq ft · 74 pcs · 12 steps4×12 Lean-To Shed48 sq ft · 79 pcs · 12 steps6×8 Lean-To Shed48 sq ft · 74 pcs · 12 steps4×14 Lean-To Shed56 sq ft · 86 pcs · 12 steps