Design your own

6×14 Lean-To Shed Plans

This 6×14 lean-to shed sits on pressure-treated skids on gravel, with 8′ walls, a 3/12 single-slope roof and a peak of 11′ 1-5/8″. The 38″-wide door opening gets a doubled header sized for the roof load above it. Rafters are 2x4 at 16″ on center. All 93 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 81 boards plus sheet goods and hardware.

Footprint6′ 0″ × 14′ 0″
Area84 sq ft
Height11′ 1-5/8″
Lumber93 pcs
Steps12
Checks8 pass

Open in the builderJump to the steps

3D model of the 6×14 lean-to shed framing

Shopping list

332x4 × 8′
242x4 × 10′
22x4 × 14′
32x4 × 16′
12x6 × 8′
14PT 2x6 × 8′
2PT 2x6 × 14′
2PT 4x6 × 16′
53/4" T&G plywood subfloor, 4×8
147/16" OSB wall sheathing, 4×8 (10% waste)
51/2" OSB roof sheathing, 4×8 (15% waste)
4bundles shingles (1.2 squares + 10%)
1rolls synthetic underlayment
12hurricane ties, rafter to plate

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A2PT 4x6168"Skidsquare both ends
B2PT 2x6166-1/2"Rim joistsquare ends; laps the next piece at the corner
C2PT 2x670-1/2"Rim joistsquare ends; laps the next piece at the corner
D12PT 2x669"Floor joistsquare both ends
E22x641"Header plysquare; two plies with a 1/2" plywood spacer
F12x4164-1/2"Top platesquare ends; laps the next piece at the corner
G92x492-5/8"Studsquare both ends
H22x492-5/8"King studsquare both ends
J22x476-1/2"Jack studsquare both ends
K12x465"Bottom platesquare ends; laps the next piece at the corner
L12x461-1/2"Bottom platesquare ends; laps the next piece at the corner
M22x410-5/8"Cripplesquare both ends
N62x492-5/8"Studsquare both ends
P12x468-1/2"Bottom platesquare ends; laps the next piece at the corner
Q12x468-1/2"Top platesquare ends; laps the next piece at the corner
R12x4168"Bottom platesquare ends; laps the next piece at the corner
S12x4168"Top platesquare ends; laps the next piece at the corner
T122x4109-3/4"Studsquare both ends
U62x492-5/8"Studsquare both ends
V12x465"Bottom platesquare ends; laps the next piece at the corner
W12x465"Top platesquare ends; laps the next piece at the corner
X12x4168"Cap platelaps over the next wall at the corner
Y12x4164-1/2"Cap platelaps over the next wall at the corner
Z12x468-1/2"Cap platelaps over the next wall at the corner
AA12x465"Cap platelaps over the next wall at the corner
AB122x499-13/16"Common rafterplumb cuts 3/12 at both tails; birdsmouth seat 1-1/2", heel 3/8"; tail plumb cut 12" past the wall
AC22x416-3/4"Rake studtop cut 3/12 (14.0°), long point up
AD12x415-13/16"Rake studtop cut 3/12 (14.0°), long point up
AE12x413-13/16"Rake studtop cut 3/12 (14.0°), long point up
AF12x411-13/16"Rake studtop cut 3/12 (14.0°), long point up
AG12x49-13/16"Rake studtop cut 3/12 (14.0°), long point up
AH12x47-13/16"Rake studtop cut 3/12 (14.0°), long point up
AJ12x45-13/16"Rake studtop cut 3/12 (14.0°), long point up
AK12x43-13/16"Rake studtop cut 3/12 (14.0°), long point up

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Lay the skids

    Lay the skids

    A ×2 4x6 168"

    • Compact 4" of gravel 2 ft past the footprint.
    • Lay A parallel, level within 1/4".

    rakelevel

  2. Step 2: Frame the floor

    Frame the floor

    B ×2 2x6 166-1/2"C ×2 2x6 70-1/2"D ×12 2x6 69"

    • Rims B, C around the outside, corners lapped as drawn.
    • Mark joists every 16" along the rims.
    • Joists D between the rims: 3 nails each end.
    • Measure both diagonals. Equal = square.

    sawhammersquaretape

  3. Step 3: Lay the subfloor

    Lay the subfloor

    • Long edge across the joists, rows staggered 4 ft.
    • Glue on every joist. Screws 6" on edges, 12" in the middle.

    drillsawchalk line

  4. Step 4: Build the front wall

    Build the front wall

    E ×2 2x6 41"F ×1 2x4 164-1/2"G ×9 2x4 92-5/8"H ×2 2x4 92-5/8"J ×2 2x4 76-1/2"K ×1 2x4 65"L ×1 2x4 61-1/2"M ×2 2x4 10-5/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 127-1/4" · 143-1/4" · 159-1/4" · 163"
    • Frame the 38" × 78" door: kings, jacks, header.
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  5. Step 5: Build the right wall

    Build the right wall

    N ×6 2x4 92-5/8"P ×1 2x4 68-1/2"Q ×1 2x4 68-1/2"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 67"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  6. Step 6: Build the back wall

    Build the back wall

    R ×1 2x4 168"S ×1 2x4 168"T ×12 2x4 109-3/4"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 127-1/4" · 143-1/4" · 159-1/4" · 166-1/2"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  7. Step 7: Build the left wall

    Build the left wall

    U ×6 2x4 92-5/8"V ×1 2x4 65"W ×1 2x4 65"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 3-1/2" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 67"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  8. Step 8: Lap the cap plates

    Lap the cap plates

    X ×1 2x4 168"Y ×1 2x4 164-1/2"Z ×1 2x4 68-1/2"AA ×1 2x4 65"

    • Cap plates overlap every corner. That ties the walls into one box.
    • Nails every 16", two at each lap.

    hammer

  9. Step 9: Set the rafters

    Set the rafters

    AB ×12 2x4 99-13/16"

    • Cut ONE pattern rafter. Check it in three places. Then cut the rest.
    • Every 16", over the studs.
    • Hurricane tie every rafter to the plate.

    speed squaresawdrill

  10. Step 10: Fill the end walls

    Fill the end walls

    AC ×2 2x4 16-3/4"AD ×1 2x4 15-13/16"AE ×1 2x4 13-13/16"AF ×1 2x4 11-13/16"AG ×1 2x4 9-13/16"AH ×1 2x4 7-13/16"AJ ×1 2x4 5-13/16"AK ×1 2x4 3-13/16"

    • Studs every 16" from the cap up to the rafter.
    • Measure each in place. Long point up.

    speed squaresaw

  11. Step 11: Sheath the walls

    Sheath the walls

    • Sheets vertical, edges on studs, 1/8" gaps.
    • Nails 6" on edges, 12" in the middle. Cut out the openings after.

    sawnailerchalk line

  12. Step 12: Sheath the roof

    Sheath the roof

    • Long edge across the rafters, H-clips between, rows staggered.
    • Drip edge, underlayment, drip edge, shingles.

    sawnailer

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 103 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 103 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x6 33% used
2x6 SPF #2, span 5.71 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 3259 in·lb → fb = M/S = 431 psi ≤ F'b = 1308 psi  (33% used)
Shear: fv = 1.5V/A = 35 psi ≤ F'v = 135 psi  (26% used)
Deflection: 5wL⁴/384EI = 0.044" ≤ L/360 = 0.190"  (23% used)
✓ Rafters 2x4 38% used
2x4 SPF #2, span 5.71 ft, w = 42 plf total / 28 plf live
Bending: M = wL²/8 = 2040 in·lb → fb = M/S = 666 psi ≤ F'b = 1736 psi  (38% used)
Shear: fv = 1.5V/A = 34 psi ≤ F'v = 155 psi  (22% used)
Deflection: 5wL⁴/384EI = 0.089" ≤ L/240 = 0.285"  (31% used)
✓ Header over door (front) 2x6 13% used
2-ply 2x6 SPF #2, span 3.42 ft, w = 125 plf total / 84 plf live
Bending: M = wL²/8 = 2193 in·lb → fb = M/S = 145 psi ≤ F'b = 1308 psi  (11% used)
Shear: fv = 1.5V/A = 19 psi ≤ F'v = 155 psi  (13% used)
Deflection: 5wL⁴/384EI = 0.004" ≤ L/240 = 0.171"  (3% used)
✓ Studs (front wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 167 lb  (6% used)
✓ Studs (back wall) 63% used
2x4 SPF #2, unbraced length 109.8" (le/d = 31.4 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 426 psi → Cp = 0.262
Capacity = Cp·F*c·A = 2090 lb ≥ load 167 lb  (8% used)
✓ Birdsmouth notch shear (rafters) 2x4 43% used
Heel cut 3/8" plumb leaves dn = 3.14" of the 3.5" depth over the bearing.
NDS 3.4.3.2 notched end: V'r = 2/3 · F'v · b · dn · (dn/d)² = 391 lb ≥ reaction 167 lb (43% used)

Roof: 10 psf dead + snow 0.7 × 30 = 21 psf. Floor: 40 psf live + 10 psf dead. 2 skids on 4" of compacted gravel, level within 1/4".

Questions

How much lumber does a 6x14 Lean-To Shed need?

33 2x4 × 8′, 24 2x4 × 10′, 2 2x4 × 14′, 3 2x4 × 16′, 1 2x6 × 8′, 14 PT 2x6 × 8′, 2 PT 2x6 × 14′, 2 PT 4x6 × 16′. 5 3/4" T&G plywood subfloor, 4×8; 14 7/16" OSB wall sheathing, 4×8 (10% waste); 5 1/2" OSB roof sheathing, 4×8 (15% waste).

What size rafters does a 6x14 Lean-To Shed need?

2x4 at 16″ on center, using 38% of their capacity at 30 psf ground snow. The bending, shear and deflection numbers are in the proof section.

What size joists does a 6x14 Lean-To Shed need?

2x6 at 16″ on center, using 33% of capacity at 40 psf live load.

How tall is it?

11′ 1-5/8″ at the peak, measured from the ground.

Do I need a permit for a 6x14 Lean-To Shed?

It covers 84 sq ft. The model code (IRC R105.2) exempts one-story detached accessory buildings up to 200 sq ft, and many towns set the line at 120 sq ft. Call your building department before you dig.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

8×10 Lean-To Shed80 sq ft · 86 pcs · 12 steps6×12 Lean-To Shed72 sq ft · 86 pcs · 12 steps6×16 Lean-To Shed96 sq ft · 98 pcs · 12 steps8×12 Lean-To Shed96 sq ft · 91 pcs · 12 steps10×10 Lean-To Shed100 sq ft · 93 pcs · 12 steps4×16 Lean-To Shed64 sq ft · 91 pcs · 12 steps