Design your own

8×10 Backyard Office Plans

This 8×10 backyard office sits on pressure-treated skids on gravel, with 8′ walls, a 3/12 single-slope roof and a peak of 11′ 8-5/8″. The 38″-wide door opening gets a doubled header sized for the roof load above it. Rafters are 2x4 at 16″ on center. All 97 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 75 boards plus sheet goods and hardware.

Footprint8′ 0″ × 10′ 0″
Area80 sq ft
Height11′ 8-5/8″
Lumber97 pcs
Steps12
Checks9 pass

Open in the builderJump to the steps

3D model of the 8×10 backyard office framing

Shopping list

352x4 × 8′
112x4 × 10′
122x4 × 12′
22x6 × 8′
11PT 2x6 × 8′
2PT 2x6 × 10′
2PT 4x6 × 12′
43/4" T&G plywood subfloor, 4×8
137/16" OSB wall sheathing, 4×8 (10% waste)
41/2" OSB roof sheathing, 4×8 (15% waste)
4bundles shingles (1.1 squares + 10%)
1rolls synthetic underlayment
9hurricane ties, rafter to plate

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A2PT 4x6120"Skidsquare both ends
B2PT 2x6118-1/2"Rim joistsquare ends; laps the next piece at the corner
C2PT 2x694-1/2"Rim joistsquare ends; laps the next piece at the corner
D9PT 2x693"Floor joistsquare both ends
E22x641"Header plysquare; two plies with a 1/2" plywood spacer
F22x639-1/2"Header plysquare; two plies with a 1/2" plywood spacer
G12x4116-1/2"Top platesquare ends; laps the next piece at the corner
H42x492-5/8"Studsquare both ends
J42x492-5/8"King studsquare both ends
K22x481"Jack studsquare both ends
L22x477"Jack studsquare both ends
M12x460-1/2"Bottom platesquare ends; laps the next piece at the corner
N12x436-1/2"Rough sillsquare both ends
P42x427"Cripplesquare both ends
Q12x418"Bottom platesquare ends; laps the next piece at the corner
R22x410-1/8"Cripplesquare both ends
S22x46-1/8"Cripplesquare both ends
T72x492-5/8"Studsquare both ends
U12x492-1/2"Bottom platesquare ends; laps the next piece at the corner
V12x492-1/2"Top platesquare ends; laps the next piece at the corner
W12x4120"Bottom platesquare ends; laps the next piece at the corner
X12x4120"Top platesquare ends; laps the next piece at the corner
Y92x4115-3/4"Studsquare both ends
Z72x492-5/8"Studsquare both ends
AA12x489"Bottom platesquare ends; laps the next piece at the corner
AB12x489"Top platesquare ends; laps the next piece at the corner
AC12x4120"Cap platelaps over the next wall at the corner
AD12x4116-1/2"Cap platelaps over the next wall at the corner
AE12x492-1/2"Cap platelaps over the next wall at the corner
AF12x489"Cap platelaps over the next wall at the corner
AG92x4132-13/16"Common rafterplumb cuts 3/12 at both tails; birdsmouth seat 1-1/2", heel 3/8"; tail plumb cut 16" past the wall
AH22x422-3/4"Rake studtop cut 3/12 (14.0°), long point up
AJ22x419-13/16"Rake studtop cut 3/12 (14.0°), long point up
AK22x415-13/16"Rake studtop cut 3/12 (14.0°), long point up
AL22x411-13/16"Rake studtop cut 3/12 (14.0°), long point up
AM22x47-13/16"Rake studtop cut 3/12 (14.0°), long point up
AN22x43-13/16"Rake studtop cut 3/12 (14.0°), long point up

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Lay the skids

    Lay the skids

    A ×2 4x6 120"

    • Compact 4" of gravel 2 ft past the footprint.
    • Lay A parallel, level within 1/4".

    rakelevel

  2. Step 2: Frame the floor

    Frame the floor

    B ×2 2x6 118-1/2"C ×2 2x6 94-1/2"D ×9 2x6 93"

    • Rims B, C around the outside, corners lapped as drawn.
    • Mark joists every 16" along the rims.
    • Joists D between the rims: 3 nails each end.
    • Measure both diagonals. Equal = square.

    sawhammersquaretape

  3. Step 3: Lay the subfloor

    Lay the subfloor

    • Long edge across the joists, rows staggered 4 ft.
    • Glue on every joist. Screws 6" on edges, 12" in the middle.

    drillsawchalk line

  4. Step 4: Build the front wall

    Build the front wall

    E ×2 2x6 41"F ×2 2x6 39-1/2"G ×1 2x4 116-1/2"H ×4 2x4 92-5/8"J ×4 2x4 92-5/8"K ×2 2x4 81"L ×2 2x4 77"M ×1 2x4 60-1/2"N ×1 2x4 36-1/2"P ×4 2x4 27"Q ×1 2x4 18"R ×2 2x4 10-1/8"S ×2 2x4 6-1/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 115"
    • Frame the 38" × 82-1/2" door and the 36-1/2" × 48-1/2" window: kings, jacks, header.
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  5. Step 5: Build the right wall

    Build the right wall

    T ×7 2x4 92-5/8"U ×1 2x4 92-1/2"V ×1 2x4 92-1/2"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 91"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  6. Step 6: Build the back wall

    Build the back wall

    W ×1 2x4 120"X ×1 2x4 120"Y ×9 2x4 115-3/4"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 118-1/2"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  7. Step 7: Build the left wall

    Build the left wall

    Z ×7 2x4 92-5/8"AA ×1 2x4 89"AB ×1 2x4 89"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 3-1/2" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 91"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  8. Step 8: Lap the cap plates

    Lap the cap plates

    AC ×1 2x4 120"AD ×1 2x4 116-1/2"AE ×1 2x4 92-1/2"AF ×1 2x4 89"

    • Cap plates overlap every corner. That ties the walls into one box.
    • Nails every 16", two at each lap.

    hammer

  9. Step 9: Set the rafters

    Set the rafters

    AG ×9 2x4 132-13/16"

    • Cut ONE pattern rafter. Check it in three places. Then cut the rest.
    • Every 16", over the studs.
    • Hurricane tie every rafter to the plate.

    speed squaresawdrill

  10. Step 10: Fill the end walls

    Fill the end walls

    AH ×2 2x4 22-3/4"AJ ×2 2x4 19-13/16"AK ×2 2x4 15-13/16"AL ×2 2x4 11-13/16"AM ×2 2x4 7-13/16"AN ×2 2x4 3-13/16"

    • Studs every 16" from the cap up to the rafter.
    • Measure each in place. Long point up.

    speed squaresaw

  11. Step 11: Sheath the walls

    Sheath the walls

    • Sheets vertical, edges on studs, 1/8" gaps.
    • Nails 6" on edges, 12" in the middle. Cut out the openings after.

    sawnailerchalk line

  12. Step 12: Sheath the roof

    Sheath the roof

    • Long edge across the rafters, H-clips between, rows staggered.
    • Drip edge, underlayment, drip edge, shingles.

    sawnailer

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 106 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 106 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x6 60% used
2x6 SPF #2, span 7.71 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 5942 in·lb → fb = M/S = 786 psi ≤ F'b = 1308 psi  (60% used)
Shear: fv = 1.5V/A = 47 psi ≤ F'v = 135 psi  (35% used)
Deflection: 5wL⁴/384EI = 0.146" ≤ L/360 = 0.257"  (57% used)
✓ Rafters 2x4 77% used
2x4 SPF #2, span 7.71 ft, w = 42 plf total / 28 plf live
Bending: M = wL²/8 = 3721 in·lb → fb = M/S = 1215 psi ≤ F'b = 1736 psi  (70% used)
Shear: fv = 1.5V/A = 46 psi ≤ F'v = 155 psi  (30% used)
Deflection: 5wL⁴/384EI = 0.296" ≤ L/240 = 0.385"  (77% used)
✓ Header over door (front) 2x6 17% used
2-ply 2x6 SPF #2, span 3.42 ft, w = 167 plf total / 112 plf live
Bending: M = wL²/8 = 2924 in·lb → fb = M/S = 193 psi ≤ F'b = 1308 psi  (15% used)
Shear: fv = 1.5V/A = 26 psi ≤ F'v = 155 psi  (17% used)
Deflection: 5wL⁴/384EI = 0.006" ≤ L/240 = 0.171"  (3% used)
✓ Header over window (front) 2x6 16% used
2-ply 2x6 SPF #2, span 3.29 ft, w = 167 plf total / 112 plf live
Bending: M = wL²/8 = 2714 in·lb → fb = M/S = 179 psi ≤ F'b = 1308 psi  (14% used)
Shear: fv = 1.5V/A = 25 psi ≤ F'v = 155 psi  (16% used)
Deflection: 5wL⁴/384EI = 0.005" ≤ L/240 = 0.165"  (3% used)
✓ Studs (front wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 223 lb  (8% used)
✓ Studs (back wall) 66% used
2x4 SPF #2, unbraced length 115.8" (le/d = 33.1 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 383 psi → Cp = 0.237
Capacity = Cp·F*c·A = 1894 lb ≥ load 223 lb  (12% used)
✓ Birdsmouth notch shear (rafters) 2x4 57% used
Heel cut 3/8" plumb leaves dn = 3.14" of the 3.5" depth over the bearing.
NDS 3.4.3.2 notched end: V'r = 2/3 · F'v · b · dn · (dn/d)² = 391 lb ≥ reaction 223 lb (57% used)

Roof: 10 psf dead + snow 0.7 × 30 = 21 psf. Floor: 40 psf live + 10 psf dead. 2 skids on 4" of compacted gravel, level within 1/4".

Questions

How much lumber does a 8x10 Backyard Office need?

35 2x4 × 8′, 11 2x4 × 10′, 12 2x4 × 12′, 2 2x6 × 8′, 11 PT 2x6 × 8′, 2 PT 2x6 × 10′, 2 PT 4x6 × 12′. 4 3/4" T&G plywood subfloor, 4×8; 13 7/16" OSB wall sheathing, 4×8 (10% waste); 4 1/2" OSB roof sheathing, 4×8 (15% waste).

What size rafters does a 8x10 Backyard Office need?

2x4 at 16″ on center, using 77% of their capacity at 30 psf ground snow. The bending, shear and deflection numbers are in the proof section.

What size joists does a 8x10 Backyard Office need?

2x6 at 16″ on center, using 60% of capacity at 40 psf live load.

How tall is it?

11′ 8-5/8″ at the peak, measured from the ground.

Do I need a permit for a 8x10 Backyard Office?

It covers 80 sq ft. The model code (IRC R105.2) exempts one-story detached accessory buildings up to 200 sq ft, and many towns set the line at 120 sq ft. Call your building department before you dig.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

8×12 Backyard Office96 sq ft · 103 pcs · 12 steps10×12 Backyard Office120 sq ft · 110 pcs · 12 steps10×14 Backyard Office140 sq ft · 118 pcs · 12 steps12×16 Backyard Office192 sq ft · 127 pcs · 12 steps