Design your own

10×16 Lean-To Shed Plans

This 10×16 lean-to shed sits on pressure-treated skids on gravel, with 8′ walls, a 3/12 single-slope roof and a peak of 12′ 5-7/16″. The 38″-wide door opening gets a doubled header sized for the roof load above it. Rafters are 2x6 at 16″ on center. All 110 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 92 boards plus sheet goods and hardware.

Footprint10′ 0″ × 16′ 0″
Area160 sq ft
Height12′ 5-7/16″
Lumber110 pcs
Steps12
Checks8 pass

Open in the builderJump to the steps

3D model of the 10×16 lean-to shed framing

Shopping list

352x4 × 8′
62x4 × 10′
132x4 × 12′
22x4 × 16′
32x4 × 20′
12x6 × 8′
132x6 × 14′
15PT 2x8 × 10′
2PT 2x8 × 16′
2PT 4x6 × 20′
73/4" T&G plywood subfloor, 4×8
197/16" OSB wall sheathing, 4×8 (10% waste)
81/2" OSB roof sheathing, 4×8 (15% waste)
7bundles shingles (2.0 squares + 10%)
1rolls synthetic underlayment
13hurricane ties, rafter to plate

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A2PT 4x6192"Skidsquare both ends
B2PT 2x8190-1/2"Rim joistsquare ends; laps the next piece at the corner
C2PT 2x8118-1/2"Rim joistsquare ends; laps the next piece at the corner
D13PT 2x8117"Floor joistsquare both ends
E22x641"Header plysquare; two plies with a 1/2" plywood spacer
F12x4188-1/2"Top platesquare ends; laps the next piece at the corner
G102x492-5/8"Studsquare both ends
H22x492-5/8"King studsquare both ends
J12x477"Bottom platesquare ends; laps the next piece at the corner
K22x476-1/2"Jack studsquare both ends
L12x473-1/2"Bottom platesquare ends; laps the next piece at the corner
M32x410-5/8"Cripplesquare both ends
N12x4116-1/2"Bottom platesquare ends; laps the next piece at the corner
P12x4116-1/2"Top platesquare ends; laps the next piece at the corner
Q92x492-5/8"Studsquare both ends
R12x4192"Bottom platesquare ends; laps the next piece at the corner
S12x4192"Top platesquare ends; laps the next piece at the corner
T132x4121-3/4"Studsquare both ends
U12x4113"Bottom platesquare ends; laps the next piece at the corner
V12x4113"Top platesquare ends; laps the next piece at the corner
W92x492-5/8"Studsquare both ends
X12x4192"Cap platelaps over the next wall at the corner
Y12x4188-1/2"Cap platelaps over the next wall at the corner
Z12x4116-1/2"Cap platelaps over the next wall at the corner
AA12x4113"Cap platelaps over the next wall at the corner
AB132x6149-13/16"Common rafterplumb cuts 3/12 at both tails; birdsmouth seat 1-1/2", heel 3/8"; tail plumb cut 12" past the wall
AC22x428-3/4"Rake studtop cut 3/12 (14.0°), long point up
AD12x427-13/16"Rake studtop cut 3/12 (14.0°), long point up
AE12x425-13/16"Rake studtop cut 3/12 (14.0°), long point up
AF12x423-13/16"Rake studtop cut 3/12 (14.0°), long point up
AG12x421-13/16"Rake studtop cut 3/12 (14.0°), long point up
AH12x419-13/16"Rake studtop cut 3/12 (14.0°), long point up
AJ12x417-13/16"Rake studtop cut 3/12 (14.0°), long point up
AK12x415-13/16"Rake studtop cut 3/12 (14.0°), long point up
AL12x413-13/16"Rake studtop cut 3/12 (14.0°), long point up
AM12x411-13/16"Rake studtop cut 3/12 (14.0°), long point up
AN12x49-13/16"Rake studtop cut 3/12 (14.0°), long point up
AP12x47-13/16"Rake studtop cut 3/12 (14.0°), long point up
AQ12x45-13/16"Rake studtop cut 3/12 (14.0°), long point up
AR12x43-13/16"Rake studtop cut 3/12 (14.0°), long point up

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Lay the skids

    Lay the skids

    A ×2 4x6 192"

    • Compact 4" of gravel 2 ft past the footprint.
    • Lay A parallel, level within 1/4".

    rakelevel

  2. Step 2: Frame the floor

    Frame the floor

    B ×2 2x8 190-1/2"C ×2 2x8 118-1/2"D ×13 2x8 117"

    • Rims B, C around the outside, corners lapped as drawn.
    • Mark joists every 16" along the rims.
    • Joists D between the rims: 3 nails each end.
    • Measure both diagonals. Equal = square.

    sawhammersquaretape

  3. Step 3: Lay the subfloor

    Lay the subfloor

    • Long edge across the joists, rows staggered 4 ft.
    • Glue on every joist. Screws 6" on edges, 12" in the middle.

    drillsawchalk line

  4. Step 4: Build the front wall

    Build the front wall

    E ×2 2x6 41"F ×1 2x4 188-1/2"G ×10 2x4 92-5/8"H ×2 2x4 92-5/8"J ×1 2x4 77"K ×2 2x4 76-1/2"L ×1 2x4 73-1/2"M ×3 2x4 10-5/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 127-1/4" · 143-1/4" · 159-1/4" · 175-1/4" · 187"
    • Frame the 38" × 78" door: kings, jacks, header.
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  5. Step 5: Build the right wall

    Build the right wall

    N ×1 2x4 116-1/2"P ×1 2x4 116-1/2"Q ×9 2x4 92-5/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 115"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  6. Step 6: Build the back wall

    Build the back wall

    R ×1 2x4 192"S ×1 2x4 192"T ×13 2x4 121-3/4"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 127-1/4" · 143-1/4" · 159-1/4" · 175-1/4" · 190-1/2"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  7. Step 7: Build the left wall

    Build the left wall

    U ×1 2x4 113"V ×1 2x4 113"W ×9 2x4 92-5/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 3-1/2" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 115"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  8. Step 8: Lap the cap plates

    Lap the cap plates

    X ×1 2x4 192"Y ×1 2x4 188-1/2"Z ×1 2x4 116-1/2"AA ×1 2x4 113"

    • Cap plates overlap every corner. That ties the walls into one box.
    • Nails every 16", two at each lap.

    hammer

  9. Step 9: Set the rafters

    Set the rafters

    AB ×13 2x6 149-13/16"

    • Cut ONE pattern rafter. Check it in three places. Then cut the rest.
    • Every 16", over the studs.
    • Hurricane tie every rafter to the plate.

    speed squaresawdrill

  10. Step 10: Fill the end walls

    Fill the end walls

    AC ×2 2x4 28-3/4"AD ×1 2x4 27-13/16"AE ×1 2x4 25-13/16"AF ×1 2x4 23-13/16"AG ×1 2x4 21-13/16"AH ×1 2x4 19-13/16"AJ ×1 2x4 17-13/16"AK ×1 2x4 15-13/16"AL ×1 2x4 13-13/16"AM ×1 2x4 11-13/16"AN ×1 2x4 9-13/16"AP ×1 2x4 7-13/16"AQ ×1 2x4 5-13/16"AR ×1 2x4 3-13/16"

    • Studs every 16" from the cap up to the rafter.
    • Measure each in place. Long point up.

    speed squaresaw

  11. Step 11: Sheath the walls

    Sheath the walls

    • Sheets vertical, edges on studs, 1/8" gaps.
    • Nails 6" on edges, 12" in the middle. Cut out the openings after.

    sawnailerchalk line

  12. Step 12: Sheath the roof

    Sheath the roof

    • Long edge across the rafters, H-clips between, rows staggered.
    • Drip edge, underlayment, drip edge, shingles.

    sawnailer

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 122 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 122 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x8 59% used
2x8 SPF #2, span 9.71 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 9425 in·lb → fb = M/S = 717 psi ≤ F'b = 1208 psi  (59% used)
Shear: fv = 1.5V/A = 45 psi ≤ F'v = 135 psi  (33% used)
Deflection: 5wL⁴/384EI = 0.160" ≤ L/360 = 0.324"  (49% used)
✓ Rafters 2x6 52% used
2x6 SPF #2, span 9.71 ft, w = 42 plf total / 28 plf live
Bending: M = wL²/8 = 5902 in·lb → fb = M/S = 780 psi ≤ F'b = 1504 psi  (52% used)
Shear: fv = 1.5V/A = 37 psi ≤ F'v = 155 psi  (24% used)
Deflection: 5wL⁴/384EI = 0.192" ≤ L/240 = 0.485"  (40% used)
✓ Header over door (front) 2x6 19% used
2-ply 2x6 SPF #2, span 3.42 ft, w = 188 plf total / 126 plf live
Bending: M = wL²/8 = 3289 in·lb → fb = M/S = 217 psi ≤ F'b = 1308 psi  (17% used)
Shear: fv = 1.5V/A = 29 psi ≤ F'v = 155 psi  (19% used)
Deflection: 5wL⁴/384EI = 0.007" ≤ L/240 = 0.171"  (4% used)
✓ Studs (front wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 250 lb  (9% used)
✓ Studs (back wall) 70% used
2x4 SPF #2, unbraced length 121.8" (le/d = 34.8 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 346 psi → Cp = 0.216
Capacity = Cp·F*c·A = 1724 lb ≥ load 250 lb  (15% used)
✓ Birdsmouth notch shear (rafters) 2x6 36% used
Heel cut 3/8" plumb leaves dn = 5.14" of the 5.5" depth over the bearing.
NDS 3.4.3.2 notched end: V'r = 2/3 · F'v · b · dn · (dn/d)² = 695 lb ≥ reaction 250 lb (36% used)

Roof: 10 psf dead + snow 0.7 × 30 = 21 psf. Floor: 40 psf live + 10 psf dead. 2 skids on 4" of compacted gravel, level within 1/4".

Questions

How much lumber does a 10x16 Lean-To Shed need?

35 2x4 × 8′, 6 2x4 × 10′, 13 2x4 × 12′, 2 2x4 × 16′, 3 2x4 × 20′, 1 2x6 × 8′, 13 2x6 × 14′, 15 PT 2x8 × 10′, 2 PT 2x8 × 16′, 2 PT 4x6 × 20′. 7 3/4" T&G plywood subfloor, 4×8; 19 7/16" OSB wall sheathing, 4×8 (10% waste); 8 1/2" OSB roof sheathing, 4×8 (15% waste).

What size rafters does a 10x16 Lean-To Shed need?

2x6 at 16″ on center, using 52% of their capacity at 30 psf ground snow. The bending, shear and deflection numbers are in the proof section.

What size joists does a 10x16 Lean-To Shed need?

2x8 at 16″ on center, using 59% of capacity at 40 psf live load.

How tall is it?

12′ 5-7/16″ at the peak, measured from the ground.

Do I need a permit for a 10x16 Lean-To Shed?

It covers 160 sq ft. The model code (IRC R105.2) exempts one-story detached accessory buildings up to 200 sq ft, and many towns set the line at 120 sq ft. Call your building department before you dig.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

12×14 Lean-To Shed168 sq ft · 110 pcs · 12 steps12×12 Lean-To Shed144 sq ft · 103 pcs · 12 steps10×14 Lean-To Shed140 sq ft · 105 pcs · 12 steps8×16 Lean-To Shed128 sq ft · 103 pcs · 12 steps12×16 Lean-To Shed192 sq ft · 115 pcs · 12 steps10×12 Lean-To Shed120 sq ft · 98 pcs · 12 steps