12×14 Lean-To Shed Plans
This 12×14 lean-to shed sits on pressure-treated skids on gravel, with 8′ walls, a 3/12 single-slope roof and a peak of 12′ 11-7/16″. The 38″-wide door opening gets a doubled header sized for the roof load above it. Rafters are 2x6 at 16″ on center. All 110 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 91 boards plus sheet goods and hardware.

Shopping list
Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.
Parts and cut list
Cut every part, then pencil its letter on it. The steps call parts by letter.
| Part | Qty | Size | Length | Piece | How to cut |
|---|---|---|---|---|---|
| A | 2 | PT 4x6 | 168" | Skid | square both ends |
| B | 2 | PT 2x8 | 166-1/2" | Rim joist | square ends; laps the next piece at the corner |
| C | 2 | PT 2x8 | 142-1/2" | Rim joist | square ends; laps the next piece at the corner |
| D | 12 | PT 2x8 | 141" | Floor joist | square both ends |
| E | 2 | 2x6 | 41" | Header ply | square; two plies with a 1/2" plywood spacer |
| F | 1 | 2x4 | 164-1/2" | Top plate | square ends; laps the next piece at the corner |
| G | 9 | 2x4 | 92-5/8" | Stud | square both ends |
| H | 2 | 2x4 | 92-5/8" | King stud | square both ends |
| J | 2 | 2x4 | 76-1/2" | Jack stud | square both ends |
| K | 1 | 2x4 | 65" | Bottom plate | square ends; laps the next piece at the corner |
| L | 1 | 2x4 | 61-1/2" | Bottom plate | square ends; laps the next piece at the corner |
| M | 2 | 2x4 | 10-5/8" | Cripple | square both ends |
| N | 1 | 2x4 | 140-1/2" | Bottom plate | square ends; laps the next piece at the corner |
| P | 1 | 2x4 | 140-1/2" | Top plate | square ends; laps the next piece at the corner |
| Q | 10 | 2x4 | 92-5/8" | Stud | square both ends |
| R | 1 | 2x4 | 168" | Bottom plate | square ends; laps the next piece at the corner |
| S | 1 | 2x4 | 168" | Top plate | square ends; laps the next piece at the corner |
| T | 12 | 2x4 | 127-3/4" | Stud | square both ends |
| U | 1 | 2x4 | 137" | Bottom plate | square ends; laps the next piece at the corner |
| V | 1 | 2x4 | 137" | Top plate | square ends; laps the next piece at the corner |
| W | 10 | 2x4 | 92-5/8" | Stud | square both ends |
| X | 1 | 2x4 | 168" | Cap plate | laps over the next wall at the corner |
| Y | 1 | 2x4 | 164-1/2" | Cap plate | laps over the next wall at the corner |
| Z | 1 | 2x4 | 140-1/2" | Cap plate | laps over the next wall at the corner |
| AA | 1 | 2x4 | 137" | Cap plate | laps over the next wall at the corner |
| AB | 12 | 2x6 | 174-9/16" | Common rafter | plumb cuts 3/12 at both tails; birdsmouth seat 1-1/2", heel 3/8"; tail plumb cut 12" past the wall |
| AC | 2 | 2x4 | 34-3/4" | Rake stud | top cut 3/12 (14.0°), long point up |
| AD | 2 | 2x4 | 31-13/16" | Rake stud | top cut 3/12 (14.0°), long point up |
| AE | 2 | 2x4 | 27-13/16" | Rake stud | top cut 3/12 (14.0°), long point up |
| AF | 2 | 2x4 | 23-13/16" | Rake stud | top cut 3/12 (14.0°), long point up |
| AG | 2 | 2x4 | 19-13/16" | Rake stud | top cut 3/12 (14.0°), long point up |
| AH | 2 | 2x4 | 15-13/16" | Rake stud | top cut 3/12 (14.0°), long point up |
| AJ | 2 | 2x4 | 11-13/16" | Rake stud | top cut 3/12 (14.0°), long point up |
| AK | 2 | 2x4 | 7-13/16" | Rake stud | top cut 3/12 (14.0°), long point up |
| AL | 2 | 2x4 | 3-13/16" | Rake stud | top cut 3/12 (14.0°), long point up |
Step by step
New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

Lay the skids
A ×2 4x6 168"
- Compact 4" of gravel 2 ft past the footprint.
- Lay A parallel, level within 1/4".
rakelevel

Frame the floor
B ×2 2x8 166-1/2"C ×2 2x8 142-1/2"D ×12 2x8 141"
- Rims B, C around the outside, corners lapped as drawn.
- Mark joists every 16" along the rims.
- Joists D between the rims: 3 nails each end.
- Measure both diagonals. Equal = square.
sawhammersquaretape

Lay the subfloor
- Long edge across the joists, rows staggered 4 ft.
- Glue on every joist. Screws 6" on edges, 12" in the middle.
drillsawchalk line

Build the front wall
E ×2 2x6 41"F ×1 2x4 164-1/2"G ×9 2x4 92-5/8"H ×2 2x4 92-5/8"J ×2 2x4 76-1/2"K ×1 2x4 65"L ×1 2x4 61-1/2"M ×2 2x4 10-5/8"
- Lay bottom and top plates side by side on the floor.
- Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 127-1/4" · 143-1/4" · 159-1/4" · 163"
- Frame the 38" × 78" door: kings, jacks, header.
- Nail 2 × 16d through the plates into each stud end.
- Equal diagonals, stand it up, plumb, brace.
sawhammerlevelsquare

Build the right wall
N ×1 2x4 140-1/2"P ×1 2x4 140-1/2"Q ×10 2x4 92-5/8"
- Lay bottom and top plates side by side on the floor.
- Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 127-1/4" · 139"
- Nail 2 × 16d through the plates into each stud end.
- Equal diagonals, stand it up, plumb, brace.
sawhammerlevelsquare

Build the back wall
R ×1 2x4 168"S ×1 2x4 168"T ×12 2x4 127-3/4"
- Lay bottom and top plates side by side on the floor.
- Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 127-1/4" · 143-1/4" · 159-1/4" · 166-1/2"
- Nail 2 × 16d through the plates into each stud end.
- Equal diagonals, stand it up, plumb, brace.
sawhammerlevelsquare

Build the left wall
U ×1 2x4 137"V ×1 2x4 137"W ×10 2x4 92-5/8"
- Lay bottom and top plates side by side on the floor.
- Mark stud left edges from the left end (outside view): 3-1/2" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 127-1/4" · 139"
- Nail 2 × 16d through the plates into each stud end.
- Equal diagonals, stand it up, plumb, brace.
sawhammerlevelsquare

Lap the cap plates
X ×1 2x4 168"Y ×1 2x4 164-1/2"Z ×1 2x4 140-1/2"AA ×1 2x4 137"
- Cap plates overlap every corner. That ties the walls into one box.
- Nails every 16", two at each lap.
hammer

Set the rafters
AB ×12 2x6 174-9/16"
- Cut ONE pattern rafter. Check it in three places. Then cut the rest.
- Every 16", over the studs.
- Hurricane tie every rafter to the plate.
speed squaresawdrill

Fill the end walls
AC ×2 2x4 34-3/4"AD ×2 2x4 31-13/16"AE ×2 2x4 27-13/16"AF ×2 2x4 23-13/16"AG ×2 2x4 19-13/16"AH ×2 2x4 15-13/16"AJ ×2 2x4 11-13/16"AK ×2 2x4 7-13/16"AL ×2 2x4 3-13/16"
- Studs every 16" from the cap up to the rafter.
- Measure each in place. Long point up.
speed squaresaw

Sheath the walls
- Sheets vertical, edges on studs, 1/8" gaps.
- Nails 6" on edges, 12" in the middle. Cut out the openings after.
sawnailerchalk line

Sheath the roof
- Long edge across the rafters, H-clips between, rows staggered.
- Drip edge, underlayment, drip edge, shingles.
sawnailer
The proof
Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.
✓ No two pieces occupy the same space
All 122 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 122 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x8 87% used
2x8 SPF #2, span 11.71 ft, w = 67 plf total / 53 plf live Bending: M = wL²/8 = 13709 in·lb → fb = M/S = 1043 psi ≤ F'b = 1208 psi (86% used) Shear: fv = 1.5V/A = 54 psi ≤ F'v = 135 psi (40% used) Deflection: 5wL⁴/384EI = 0.338" ≤ L/360 = 0.390" (87% used)
✓ Rafters 2x6 75% used
2x6 SPF #2, span 11.71 ft, w = 42 plf total / 28 plf live Bending: M = wL²/8 = 8584 in·lb → fb = M/S = 1135 psi ≤ F'b = 1504 psi (75% used) Shear: fv = 1.5V/A = 44 psi ≤ F'v = 155 psi (29% used) Deflection: 5wL⁴/384EI = 0.407" ≤ L/240 = 0.585" (69% used)
✓ Header over door (front) 2x6 22% used
2-ply 2x6 SPF #2, span 3.42 ft, w = 219 plf total / 147 plf live Bending: M = wL²/8 = 3837 in·lb → fb = M/S = 254 psi ≤ F'b = 1308 psi (19% used) Shear: fv = 1.5V/A = 34 psi ≤ F'v = 155 psi (22% used) Deflection: 5wL⁴/384EI = 0.008" ≤ L/240 = 0.171" (5% used)
✓ Studs (front wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50) F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355 Capacity = Cp·F*c·A = 2831 lb ≥ load 292 lb (10% used)
✓ Studs (back wall) 73% used
2x4 SPF #2, unbraced length 127.8" (le/d = 36.5 ≤ 50) F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 315 psi → Cp = 0.197 Capacity = Cp·F*c·A = 1575 lb ≥ load 292 lb (19% used)
✓ Birdsmouth notch shear (rafters) 2x6 42% used
Heel cut 3/8" plumb leaves dn = 5.14" of the 5.5" depth over the bearing. NDS 3.4.3.2 notched end: V'r = 2/3 · F'v · b · dn · (dn/d)² = 695 lb ≥ reaction 292 lb (42% used)
Roof: 10 psf dead + snow 0.7 × 30 = 21 psf. Floor: 40 psf live + 10 psf dead. 2 skids on 4" of compacted gravel, level within 1/4".
Questions
How much lumber does a 12x14 Lean-To Shed need?
37 2x4 × 8′, 18 2x4 × 12′, 2 2x4 × 14′, 3 2x4 × 16′, 1 2x6 × 8′, 12 2x6 × 16′, 14 PT 2x8 × 12′, 2 PT 2x8 × 14′, 2 PT 4x6 × 16′. 7 3/4" T&G plywood subfloor, 4×8; 19 7/16" OSB wall sheathing, 4×8 (10% waste); 8 1/2" OSB roof sheathing, 4×8 (15% waste).
What size rafters does a 12x14 Lean-To Shed need?
2x6 at 16″ on center, using 75% of their capacity at 30 psf ground snow. The bending, shear and deflection numbers are in the proof section.
What size joists does a 12x14 Lean-To Shed need?
2x8 at 16″ on center, using 87% of capacity at 40 psf live load.
How tall is it?
12′ 11-7/16″ at the peak, measured from the ground.
Do I need a permit for a 12x14 Lean-To Shed?
It covers 168 sq ft. The model code (IRC R105.2) exempts one-story detached accessory buildings up to 200 sq ft, and many towns set the line at 120 sq ft. Call your building department before you dig.
Can I change the size or add a door?
Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.
10×16 Lean-To Shed
12×12 Lean-To Shed
12×16 Lean-To Shed
10×14 Lean-To Shed
8×16 Lean-To Shed
10×12 Lean-To Shed