Design your own

12×12 Deck Plans, 30″ High

This 12′ × 12′ deck stands 30″ off the ground on posts on concrete footings. Joists are 2x8 at 16″ on center, carried by doubled 2x8 beams. The stairs and the 36″ guard are drawn and checked. All 61 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 54 boards plus sheet goods and hardware.

Footprint12′ 0″ × 12′ 0″
Area144 sq ft
Height2′ 6″
Lumber61 pcs
Steps6
Checks8 pass

Open in the builderJump to the steps

3D model of the 12×12 deck framing

Shopping list

3PT 2x12 × 8′
6PT 2x6 × 8′
18PT 2x8 × 12′
1PT 4x4 × 8′
26PT 5/4x6 × 14′
0.62cubic yards concrete (+10%)
6post bases + post caps
1boxes 2-1/2" deck screws (350/box)

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A6PT 4x414-1/2"Postsquare both ends
B4PT 2x8136"Beam plysquare; 2 plies nailed together, 10d every 16" staggered
C4PT 2x8142-1/2"Rim joistsquare ends; laps the next piece at the corner
D10PT 2x8141"Floor joistsquare both ends
E26PT 5/4x6144"Deck boardsquare both ends
F1PT 2x1248"Stair hanger boardsquare; bolt to the rim
G4PT 2x1237-3/16"Stair stringer3 notches: rise 7-1/2", run 10-1/4"; plumb cut at the top, level cut at the bottom
H6PT 2x648"Stair treadsquare both ends

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Dig and pour the footings

    Dig and pour the footings

    • Stake out 6 post spots exactly where the picture shows.
    • Dig each hole Ø20" wide, below your frost line.
    • Pour concrete. Set a post base in each one, all level with a string line.

    shovelstring linelevel

  2. Step 2: Stand the posts

    Stand the posts

    A ×6 4x4 14-1/2"

    • Cut posts A to the length in the box.
    • Fix each to its base. Plumb on two faces. Brace both ways.

    sawleveldrill

  3. Step 3: Set the beams

    Set the beams

    B ×4 2x8 136"

    • Nail each pair of B plies together, 10d nails every 16", staggered.
    • Crown up. Set on the posts and fix with post caps.

    sawhammerlevel

  4. Step 4: Frame the floor

    Frame the floor

    C ×4 2x8 142-1/2"D ×10 2x8 141"

    • Rims C around the outside, corners lapped as drawn.
    • Mark joists every 16" along the rims.
    • Joists D between the rims: 3 nails each end.
    • Measure both diagonals. Equal = square.

    sawhammersquaretape

  5. Step 5: Lay the decking

    Lay the decking

    E ×26 5/4x6 144"

    • Start at the front edge. 1/8" gap between boards (a 16d nail).
    • Two screws into every joist. Board ends only land on a joist.

    drillsawchalk line

  6. Step 6: Build the stairs

    Build the stairs

    F ×1 2x12 48"G ×4 2x12 37-3/16"H ×6 2x6 48"

    • Bolt the hanger board to the rim.
    • Lay out ONE stringer with a framing square. Test it. Cut the rest.
    • Stringers on the pad. Two screws per tread board per stringer.

    framing squaresawdrill

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 61 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 68 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x8 60% used
2x8 SPF #2, span 9.75 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 9506 in·lb → fb = M/S = 723 psi ≤ F'b = 1208 psi  (60% used)
Shear: fv = 1.5V/A = 45 psi ≤ F'v = 135 psi  (33% used)
Deflection: 5wL⁴/384EI = 0.163" ≤ L/360 = 0.325"  (50% used)
✓ Deck beams (2-ply) 2x8 89% used
2-ply 2x8 SPF #2, span 5.52 ft, w = 538 plf total / 430 plf live
Bending: M = wL²/8 = 24574 in·lb → fb = M/S = 935 psi ≤ F'b = 1050 psi  (89% used)
Shear: fv = 1.5V/A = 102 psi ≤ F'v = 135 psi  (76% used)
Deflection: 5wL⁴/384EI = 0.067" ≤ L/360 = 0.184"  (37% used)
✓ Floor posts 4x4 19% used
4x4 SPF #2, height 1.21 ft, le/d = 4.1 ≤ 50
FcE = 24425 psi → Cp = 0.989 → capacity 16019 lb ≥ load 2967 lb (19% used)
✓ Footings 95% used
Load 3117 lb ÷ 1500 psf presumptive soil bearing = 299 in² needed
20" round footing = 314 in² (95% used). Bottom below your local frost depth.
✓ Stair geometry 97% used
4 equal risers of 7-1/2" (max 7-3/4"), 3 treads: 10-1/4" run + 1" nosing (min 10").
Notched 2x12 stringers keep 5-3/16" of wood under each notch (min 5").
✓ Stair stringers 12% used
2x12 (5.20" deep after notching) SPF #2, span 2.56 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 657 in·lb → fb = M/S = 97 psi ≤ F'b = 875 psi  (11% used)
Shear: fv = 1.5V/A = 16 psi ≤ F'v = 135 psi  (12% used)
Deflection: 5wL⁴/384EI = 0.002" ≤ L/360 = 0.085"  (2% used)

Floor: 40 psf live + 10 psf dead. Footings bear on undisturbed soil below frost depth (1500 psf soil assumed). Post bases and post caps at every post.

Questions

How much lumber does a 12x12 Deck need?

3 PT 2x12 × 8′, 6 PT 2x6 × 8′, 18 PT 2x8 × 12′, 1 PT 4x4 × 8′, 26 PT 5/4x6 × 14′. 0.62 cubic yards concrete (+10%); 6 post bases + post caps; 1 boxes 2-1/2" deck screws (350/box).

What size joists does a 12x12 Deck need?

2x8 at 16″ on center, using 60% of capacity at 40 psf live load.

How big do the footings need to be?

20″ round, 6 of them, bearing below your local frost line. That assumes 1,500 psf soil.

Does a 12x12 Deck need a railing?

Not by code at 30″; guards are required above 30″. You can add one in the builder.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

12×12 Deck144 sq ft · 183 pcs · 7 steps12×12 Deck144 sq ft · 187 pcs · 7 steps12×12 Ground-Level Deck144 sq ft · 42 pcs · 3 steps10×16 Deck160 sq ft · 82 pcs · 6 steps10×16 Deck160 sq ft · 216 pcs · 7 steps10×16 Deck160 sq ft · 220 pcs · 7 steps