Design your own

10×16 Deck Plans, 48″ High

This 10′ × 16′ deck stands 48″ off the ground on posts on concrete footings. Joists are 2x6 at 16″ on center, carried by doubled 2x10 beams. The stairs and the 36″ guard are drawn and checked. All 220 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 147 boards plus sheet goods and hardware.

Footprint10′ 0″ × 16′ 0″
Area160 sq ft
Height7′ 0″
Lumber220 pcs
Steps7
Checks9 pass

Open in the builderJump to the steps

3D model of the 10×16 deck framing

Shopping list

4PT 2x10 × 16′
5PT 2x12 × 8′
32PT 2x2 × 8′
18PT 2x4 × 8′
14PT 2x6 × 8′
15PT 2x6 × 10′
2PT 2x6 × 12′
2PT 2x6 × 16′
1PT 2x6 × 20′
10PT 4x4 × 8′
22PT 5/4x6 × 8′
11PT 5/4x6 × 10′
11PT 5/4x6 × 12′
0.81cubic yards concrete (+10%)
6post bases + post caps
2boxes 2-1/2" deck screws (350/box)

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A6PT 4x432-1/4"Postsquare both ends
B4PT 2x10184"Beam plysquare; 2 plies nailed together, 10d every 16" staggered
C2PT 2x6190-1/2"Rim joistsquare ends; laps the next piece at the corner
D2PT 2x6118-1/2"Rim joistsquare ends; laps the next piece at the corner
E13PT 2x6117"Floor joistsquare both ends
F11PT 5/4x6127-15/16"Deck boardsquare both ends
G11PT 5/4x6111-15/16"Deck boardsquare both ends
H11PT 5/4x679-15/16"Deck boardsquare both ends
J11PT 5/4x663-15/16"Deck boardsquare both ends
K1PT 2x6192"Rail capflat on the post tops; mitred at corners
L2PT 2x6120"Rail capflat on the post tops; mitred at corners
M2PT 2x668-1/2"Rail capflat on the post tops; mitred at corners
N2PT 2x461-1/2"Bottom railsquare both ends
P2PT 2x461-1/2"Top railsquare both ends
Q3PT 2x459-5/16"Bottom railsquare both ends
R3PT 2x459-5/16"Top railsquare both ends
S4PT 2x454-3/4"Bottom railsquare both ends
T4PT 2x454-3/4"Top railsquare both ends
U14PT 4x441"Guard postsquare; through-bolt to the rim, two 1/2" bolts
V95PT 2x224"Balustersquare both ends
W4PT 2x1273-3/16"Stair stringer6 notches: rise 6-7/8", run 10-1/4"; plumb cut at the top, level cut at the bottom
X1PT 2x1248"Stair hanger boardsquare; bolt to the rim
Y12PT 2x648"Stair treadsquare both ends

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Dig and pour the footings

    Dig and pour the footings

    • Stake out 6 post spots exactly where the picture shows.
    • Dig each hole Ø24" wide, below your frost line.
    • Pour concrete. Set a post base in each one, all level with a string line.

    shovelstring linelevel

  2. Step 2: Stand the posts

    Stand the posts

    A ×6 4x4 32-1/4"

    • Cut posts A to the length in the box.
    • Fix each to its base. Plumb on two faces. Brace both ways.

    sawleveldrill

  3. Step 3: Set the beams

    Set the beams

    B ×4 2x10 184"

    • Nail each pair of B plies together, 10d nails every 16", staggered.
    • Crown up. Set on the posts and fix with post caps.

    sawhammerlevel

  4. Step 4: Frame the floor

    Frame the floor

    C ×2 2x6 190-1/2"D ×2 2x6 118-1/2"E ×13 2x6 117"

    • Rims C, D around the outside, corners lapped as drawn.
    • Mark joists every 16" along the rims.
    • Joists E between the rims: 3 nails each end.
    • Measure both diagonals. Equal = square.

    sawhammersquaretape

  5. Step 5: Lay the decking

    Lay the decking

    F ×11 5/4x6 127-15/16"G ×11 5/4x6 111-15/16"H ×11 5/4x6 79-15/16"J ×11 5/4x6 63-15/16"

    • Start at the front edge. 1/8" gap between boards (a 16d nail).
    • Two screws into every joist. Board ends only land on a joist.

    drillsawchalk line

  6. Step 6: Add the railing

    Add the railing

    K ×1 2x6 192"L ×2 2x6 120"M ×2 2x6 68-1/2"N ×2 2x4 61-1/2"P ×2 2x4 61-1/2"Q ×3 2x4 59-5/16"R ×3 2x4 59-5/16"S ×4 2x4 54-3/4"T ×4 2x4 54-3/4"U ×14 4x4 41"V ×95 2x2 24"

    • Posts first. Then bottom and top rails.
    • Balusters with a 3-7/8" spacer block between each.
    • Cap last.

    drillsawlevel

  7. Step 7: Build the stairs

    Build the stairs

    W ×4 2x12 73-3/16"X ×1 2x12 48"Y ×12 2x6 48"

    • Bolt the hanger board to the rim.
    • Lay out ONE stringer with a framing square. Test it. Cut the rest.
    • Stringers on the pad. Two screws per tread board per stringer.

    framing squaresawdrill

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 220 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 227 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x6 61% used
2x6 SPF #2, span 7.75 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 6006 in·lb → fb = M/S = 794 psi ≤ F'b = 1308 psi  (61% used)
Shear: fv = 1.5V/A = 47 psi ≤ F'v = 135 psi  (35% used)
Deflection: 5wL⁴/384EI = 0.149" ≤ L/360 = 0.258"  (58% used)
✓ Deck beams (2-ply) 2x10 90% used
2-ply 2x10 SPF #2, span 7.52 ft, w = 438 plf total / 350 plf live
Bending: M = wL²/8 = 37119 in·lb → fb = M/S = 868 psi ≤ F'b = 963 psi  (90% used)
Shear: fv = 1.5V/A = 89 psi ≤ F'v = 135 psi  (66% used)
Deflection: 5wL⁴/384EI = 0.091" ≤ L/360 = 0.251"  (36% used)
✓ Floor posts 4x4 22% used
4x4 SPF #2, height 2.69 ft, le/d = 9.2 ≤ 50
FcE = 4938 psi → Cp = 0.937 → capacity 15183 lb ≥ load 3290 lb (22% used)
✓ Footings 73% used
Load 3440 lb ÷ 1500 psf presumptive soil bearing = 330 in² needed
24" round footing = 452 in² (73% used). Bottom below your local frost depth.
✓ Guard geometry 90% used
36" guard height. Baluster gaps under 4", so a 4" ball cannot pass. Bottom gap 3-1/2".
Guard-post bolting follows the AWC DCA 6 detail; that connection is not calculated here.
✓ Stair geometry 88% used
7 equal risers of 6-7/8" (max 7-3/4"), 6 treads: 10-1/4" run + 1" nosing (min 10").
Notched 2x12 stringers keep 5-9/16" of wood under each notch (min 5").
✓ Stair stringers 39% used
2x12 (5.55" deep after notching) SPF #2, span 5.13 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 2627 in·lb → fb = M/S = 341 psi ≤ F'b = 875 psi  (39% used)
Shear: fv = 1.5V/A = 31 psi ≤ F'v = 135 psi  (23% used)
Deflection: 5wL⁴/384EI = 0.028" ≤ L/360 = 0.171"  (16% used)

Floor: 40 psf live + 10 psf dead. Footings bear on undisturbed soil below frost depth (1500 psf soil assumed). Post bases and post caps at every post.

Questions

How much lumber does a 10x16 Deck need?

4 PT 2x10 × 16′, 5 PT 2x12 × 8′, 32 PT 2x2 × 8′, 18 PT 2x4 × 8′, 14 PT 2x6 × 8′, 15 PT 2x6 × 10′, 2 PT 2x6 × 12′, 2 PT 2x6 × 16′, 1 PT 2x6 × 20′, 10 PT 4x4 × 8′, 22 PT 5/4x6 × 8′, 11 PT 5/4x6 × 10′, 11 PT 5/4x6 × 12′. 0.81 cubic yards concrete (+10%); 6 post bases + post caps; 2 boxes 2-1/2" deck screws (350/box).

What size joists does a 10x16 Deck need?

2x6 at 16″ on center, using 61% of capacity at 40 psf live load.

How big do the footings need to be?

24″ round, 6 of them, bearing below your local frost line. That assumes 1,500 psf soil.

Does a 10x16 Deck need a railing?

Yes. Any deck surface more than 30″ above grade needs a guard at least 36″ high, and this plan includes one.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

10×16 Deck160 sq ft · 82 pcs · 6 steps10×16 Deck160 sq ft · 216 pcs · 7 steps10×16 Ground-Level Deck160 sq ft · 63 pcs · 3 steps12×12 Deck144 sq ft · 61 pcs · 6 steps12×12 Deck144 sq ft · 183 pcs · 7 steps12×12 Deck144 sq ft · 187 pcs · 7 steps