Design your own

10×16 Ground-Level Deck Plans

This 10′ × 16′ deck stands at ground level on skids. Joists are 2x8 at 16″ on center, resting on the skids. All 63 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 63 boards plus sheet goods and hardware.

Footprint10′ 0″ × 16′ 0″
Area160 sq ft
Height1′ 1-3/4″
Lumber63 pcs
Steps3
Checks3 pass

Open in the builderJump to the steps

3D model of the 10×16 ground-level deck framing

Shopping list

15PT 2x8 × 10′
2PT 2x8 × 16′
2PT 4x6 × 20′
22PT 5/4x6 × 8′
11PT 5/4x6 × 10′
11PT 5/4x6 × 12′
2boxes 2-1/2" deck screws (350/box)

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A2PT 4x6192"Skidsquare both ends
B2PT 2x8190-1/2"Rim joistsquare ends; laps the next piece at the corner
C2PT 2x8118-1/2"Rim joistsquare ends; laps the next piece at the corner
D13PT 2x8117"Floor joistsquare both ends
E11PT 5/4x6127-15/16"Deck boardsquare both ends
F11PT 5/4x6111-15/16"Deck boardsquare both ends
G11PT 5/4x679-15/16"Deck boardsquare both ends
H11PT 5/4x663-15/16"Deck boardsquare both ends

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Lay the skids

    Lay the skids

    A ×2 4x6 192"

    • Compact 4" of gravel 2 ft past the footprint.
    • Lay A parallel, level within 1/4".

    rakelevel

  2. Step 2: Frame the floor

    Frame the floor

    B ×2 2x8 190-1/2"C ×2 2x8 118-1/2"D ×13 2x8 117"

    • Rims B, C around the outside, corners lapped as drawn.
    • Mark joists every 16" along the rims.
    • Joists D between the rims: 3 nails each end.
    • Measure both diagonals. Equal = square.

    sawhammersquaretape

  3. Step 3: Lay the decking

    Lay the decking

    E ×11 5/4x6 127-15/16"F ×11 5/4x6 111-15/16"G ×11 5/4x6 79-15/16"H ×11 5/4x6 63-15/16"

    • Start at the front edge. 1/8" gap between boards (a 16d nail).
    • Two screws into every joist. Board ends only land on a joist.

    drillsawchalk line

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 63 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 63 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x8 59% used
2x8 SPF #2, span 9.71 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 9425 in·lb → fb = M/S = 717 psi ≤ F'b = 1208 psi  (59% used)
Shear: fv = 1.5V/A = 45 psi ≤ F'v = 135 psi  (33% used)
Deflection: 5wL⁴/384EI = 0.160" ≤ L/360 = 0.324"  (49% used)

Floor: 40 psf live + 10 psf dead. 2 skids on 4" of compacted gravel, level within 1/4".

Questions

How much lumber does a 10x16 Ground-Level Deck need?

15 PT 2x8 × 10′, 2 PT 2x8 × 16′, 2 PT 4x6 × 20′, 22 PT 5/4x6 × 8′, 11 PT 5/4x6 × 10′, 11 PT 5/4x6 × 12′. 2 boxes 2-1/2" deck screws (350/box).

What size joists does a 10x16 Ground-Level Deck need?

2x8 at 16″ on center, using 59% of capacity at 40 psf live load.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

10×16 Deck160 sq ft · 82 pcs · 6 steps10×16 Deck160 sq ft · 216 pcs · 7 steps10×16 Deck160 sq ft · 220 pcs · 7 steps12×12 Deck144 sq ft · 61 pcs · 6 steps12×12 Deck144 sq ft · 183 pcs · 7 steps12×12 Deck144 sq ft · 187 pcs · 7 steps