12×20 Cabin Plans
This 12×20 cabin sits on a 4″ concrete slab, with 8′ walls, a 8/12 gable roof and a peak of 12′ 4-15/16″. The 38″-wide door opening gets a doubled header sized for the roof load above it. Rafters are 2x4 at 16″ on center. All 167 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 131 boards plus sheet goods and hardware.

Shopping list
Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.
Parts and cut list
Cut every part, then pencil its letter on it. The steps call parts by letter.
| Part | Qty | Size | Length | Piece | How to cut |
|---|---|---|---|---|---|
| A | 2 | 2x6 | 41" | Header ply | square; two plies with a 1/2" plywood spacer |
| B | 4 | 2x6 | 39-1/2" | Header ply | square; two plies with a 1/2" plywood spacer |
| C | 1 | 2x4 | 236-1/2" | Top plate | square ends; laps the next piece at the corner |
| D | 1 | PT 2x4 | 101" | Bottom plate | square ends; laps the next piece at the corner |
| E | 1 | PT 2x4 | 97-1/2" | Bottom plate | square ends; laps the next piece at the corner |
| F | 8 | 2x4 | 92-5/8" | Stud | square both ends |
| G | 6 | 2x4 | 92-5/8" | King stud | square both ends |
| H | 6 | 2x4 | 81" | Jack stud | square both ends |
| J | 2 | 2x4 | 36-1/2" | Rough sill | square both ends |
| K | 8 | 2x4 | 31" | Cripple | square both ends |
| L | 6 | 2x4 | 6-1/8" | Cripple | square both ends |
| M | 1 | PT 2x4 | 140-1/2" | Bottom plate | square ends; laps the next piece at the corner |
| N | 1 | 2x4 | 140-1/2" | Top plate | square ends; laps the next piece at the corner |
| P | 10 | 2x4 | 92-5/8" | Stud | square both ends |
| Q | 2 | 2x6 | 75-1/2" | Header ply | square; two plies with a 1/2" plywood spacer |
| R | 1 | PT 2x4 | 236-1/2" | Bottom plate | square ends; laps the next piece at the corner |
| S | 1 | 2x4 | 236-1/2" | Top plate | square ends; laps the next piece at the corner |
| T | 12 | 2x4 | 92-5/8" | Stud | square both ends |
| U | 2 | 2x4 | 92-5/8" | King stud | square both ends |
| V | 2 | 2x4 | 81" | Jack stud | square both ends |
| W | 1 | 2x4 | 72-1/2" | Rough sill | square both ends |
| X | 6 | 2x4 | 31" | Cripple | square both ends |
| Y | 4 | 2x4 | 6-1/8" | Cripple | square both ends |
| Z | 1 | PT 2x4 | 140-1/2" | Bottom plate | square ends; laps the next piece at the corner |
| AA | 1 | 2x4 | 140-1/2" | Top plate | square ends; laps the next piece at the corner |
| AB | 10 | 2x4 | 92-5/8" | Stud | square both ends |
| AC | 2 | 2x4 | 236-1/2" | Cap plate | laps over the next wall at the corner |
| AD | 2 | 2x4 | 140-1/2" | Cap plate | laps over the next wall at the corner |
| AE | 1 | 2x6 | 240" | Ridge board | square both ends |
| AF | 32 | 2x4 | 102-3/8" | Common rafter | plumb cut 8/12 at the ridge; birdsmouth seat 1-1/2", heel 1"; tail plumb cut 12" past the wall |
| AG | 14 | 2x4 | 144" | Rafter tie | top corners cut to 8/12 |
| AH | 4 | 2x4 | 42-3/16" | Gable stud | top cut 8/12 (33.7°), long point up |
| AJ | 4 | 2x4 | 31-1/2" | Gable stud | top cut 8/12 (33.7°), long point up |
| AK | 4 | 2x4 | 20-13/16" | Gable stud | top cut 8/12 (33.7°), long point up |
| AL | 4 | 2x4 | 10-3/16" | Gable stud | top cut 8/12 (33.7°), long point up |
Step by step
New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

Pour the slab
- Form, gravel, pour a 4" slab with a thickened edge.
- Anchor bolts 6" from every plate end and every 6 ft.
floatlevel

Build the front wall
A ×2 2x6 41"B ×4 2x6 39-1/2"C ×1 2x4 236-1/2"D ×1 2x4 101"E ×1 2x4 97-1/2"F ×8 2x4 92-5/8"G ×6 2x4 92-5/8"H ×6 2x4 81"J ×2 2x4 36-1/2"K ×8 2x4 31"L ×6 2x4 6-1/8"
- Lay bottom and top plates side by side on the floor.
- Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 127-1/4" · 143-1/4" · 159-1/4" · 175-1/4" · 191-1/4" · 207-1/4" · 223-1/4" · 235"
- Frame the 38" × 82-1/2" door and the 36-1/2" × 48-1/2" window and the 36-1/2" × 48-1/2" window: kings, jacks, header.
- Nail 2 × 16d through the plates into each stud end.
- Equal diagonals, stand it up, plumb, brace.
sawhammerlevelsquare

Build the right wall
M ×1 2x4 140-1/2"N ×1 2x4 140-1/2"P ×10 2x4 92-5/8"
- Lay bottom and top plates side by side on the floor.
- Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 127-1/4" · 139"
- Nail 2 × 16d through the plates into each stud end.
- Equal diagonals, stand it up, plumb, brace.
sawhammerlevelsquare

Build the back wall
Q ×2 2x6 75-1/2"R ×1 2x4 236-1/2"S ×1 2x4 236-1/2"T ×12 2x4 92-5/8"U ×2 2x4 92-5/8"V ×2 2x4 81"W ×1 2x4 72-1/2"X ×6 2x4 31"Y ×4 2x4 6-1/8"
- Lay bottom and top plates side by side on the floor.
- Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 127-1/4" · 143-1/4" · 159-1/4" · 175-1/4" · 191-1/4" · 207-1/4" · 223-1/4" · 235"
- Frame the 72-1/2" × 48-1/2" window: kings, jacks, header.
- Nail 2 × 16d through the plates into each stud end.
- Equal diagonals, stand it up, plumb, brace.
sawhammerlevelsquare

Build the left wall
Z ×1 2x4 140-1/2"AA ×1 2x4 140-1/2"AB ×10 2x4 92-5/8"
- Lay bottom and top plates side by side on the floor.
- Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 127-1/4" · 139"
- Nail 2 × 16d through the plates into each stud end.
- Equal diagonals, stand it up, plumb, brace.
sawhammerlevelsquare

Lap the cap plates
AC ×2 2x4 236-1/2"AD ×2 2x4 140-1/2"
- Cap plates overlap every corner. That ties the walls into one box.
- Nails every 16", two at each lap.
hammer

Raise the ridge
AE ×1 2x6 240"
- Ridge AE on temporary posts at the height shown.
- Plumb and brace before any rafters.
levelclamps

Set the rafters
AF ×32 2x4 102-3/8"
- Cut ONE pattern rafter. Check it in three places. Then cut the rest.
- Every 16", over the studs.
- Hurricane tie every rafter to the plate.
speed squaresawdrill

Tie the rafters
AG ×14 2x4 144"
- A tie beside every rafter pair, on the cap plates.
- Nail each end to its rafter.
hammer

Fill the gable ends
AH ×4 2x4 42-3/16"AJ ×4 2x4 31-1/2"AK ×4 2x4 20-13/16"AL ×4 2x4 10-3/16"
- Studs every 16" from the cap up to the rafter.
- Measure each in place. Long point up.
speed squaresaw

Sheath the walls
- Sheets vertical, edges on studs, 1/8" gaps.
- Nails 6" on edges, 12" in the middle. Cut out the openings after.
sawnailerchalk line

Sheath the roof
- Long edge across the rafters, H-clips between, rows staggered.
- Drip edge, underlayment, drip edge, shingles.
sawnailer
The proof
Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.
✓ No two pieces occupy the same space
All 173 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 174 pieces trace a chain of contact down to the foundation.
✓ Rafters 2x4 53% used
2x4 SPF #2, span 5.94 ft, w = 53 plf total / 37 plf live Bending: M = wL²/8 = 2822 in·lb → fb = M/S = 921 psi ≤ F'b = 1736 psi (53% used) Shear: fv = 1.5V/A = 45 psi ≤ F'v = 155 psi (29% used) Deflection: 5wL⁴/384EI = 0.139" ≤ L/240 = 0.297" (47% used)
✓ Header over door (front) 2x6 28% used
2-ply 2x6 SPF #2, span 3.42 ft, w = 280 plf total / 196 plf live Bending: M = wL²/8 = 4905 in·lb → fb = M/S = 324 psi ≤ F'b = 1308 psi (25% used) Shear: fv = 1.5V/A = 44 psi ≤ F'v = 155 psi (28% used) Deflection: 5wL⁴/384EI = 0.010" ≤ L/240 = 0.171" (6% used)
✓ Header over window (front) 2x6 27% used
2-ply 2x6 SPF #2, span 3.29 ft, w = 280 plf total / 196 plf live Bending: M = wL²/8 = 4553 in·lb → fb = M/S = 301 psi ≤ F'b = 1308 psi (23% used) Shear: fv = 1.5V/A = 42 psi ≤ F'v = 155 psi (27% used) Deflection: 5wL⁴/384EI = 0.009" ≤ L/240 = 0.165" (5% used)
✓ Header over window (front) 2x6 27% used
2-ply 2x6 SPF #2, span 3.29 ft, w = 280 plf total / 196 plf live Bending: M = wL²/8 = 4553 in·lb → fb = M/S = 301 psi ≤ F'b = 1308 psi (23% used) Shear: fv = 1.5V/A = 42 psi ≤ F'v = 155 psi (27% used) Deflection: 5wL⁴/384EI = 0.009" ≤ L/240 = 0.165" (5% used)
✓ Studs (front wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50) F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355 Capacity = Cp·F*c·A = 2831 lb ≥ load 374 lb (13% used)
✓ Header over window (back) 2x6 84% used
2-ply 2x6 SPF #2, span 6.29 ft, w = 280 plf total / 196 plf live Bending: M = wL²/8 = 16633 in·lb → fb = M/S = 1100 psi ≤ F'b = 1308 psi (84% used) Shear: fv = 1.5V/A = 80 psi ≤ F'v = 155 psi (52% used) Deflection: 5wL⁴/384EI = 0.119" ≤ L/240 = 0.315" (38% used)
✓ Studs (back wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50) F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355 Capacity = Cp·F*c·A = 2831 lb ≥ load 374 lb (13% used)
✓ Birdsmouth notch shear (rafters) 2x4 78% used
Heel cut 1" plumb leaves dn = 2.67" of the 3.5" depth over the bearing. NDS 3.4.3.2 notched end: V'r = 2/3 · F'v · b · dn · (dn/d)² = 241 lb ≥ reaction 187 lb (78% used)
Roof: 10 psf dead + snow 0.7 × 40 = 28 psf. Rafter ties at every rafter pair stop the walls spreading (a ridge board is not a beam). Nail per IRC Table R802.5.2.
Questions
How much lumber does a 12x20 Cabin need?
66 2x4 × 8′, 32 2x4 × 10′, 4 2x4 × 12′, 14 2x4 × 14′, 4 2x4 × 20′, 5 2x6 × 8′, 1 2x6 × 20′, 2 PT 2x4 × 10′, 2 PT 2x4 × 12′, 1 PT 2x4 × 20′. 20 7/16" OSB wall sheathing, 4×8 (10% waste); 13 1/2" OSB roof sheathing, 4×8 (15% waste); 12 bundles shingles (3.4 squares + 10%).
What size rafters does a 12x20 Cabin need?
2x4 at 16″ on center, using 53% of their capacity at 40 psf ground snow. The bending, shear and deflection numbers are in the proof section.
How tall is it?
12′ 4-15/16″ at the peak, measured from the ground.
Do I need a permit for a 12x20 Cabin?
It covers 240 sq ft. The model code (IRC R105.2) exempts one-story detached accessory buildings up to 200 sq ft, and many towns set the line at 120 sq ft. Call your building department before you dig.
Can I change the size or add a door?
Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.
14×20 Cabin
12×16 Cabin
16×20 Cabin
16×24 Cabin
20×24 Cabin