Design your own

16×20 Cabin Plans

This 16×20 cabin sits on a 4″ concrete slab, with 8′ walls, a 8/12 gable roof and a peak of 13′ 11-5/16″. The 38″-wide door opening gets a doubled header sized for the roof load above it. Rafters are 2x6 at 16″ on center. All 179 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 138 boards plus sheet goods and hardware.

Footprint16′ 0″ × 20′ 0″
Area320 sq ft
Height13′ 11-5/16″
Lumber179 pcs
Steps12
Checks10 pass

Open in the builderJump to the steps

3D model of the 16×20 cabin framing

Shopping list

762x4 × 8′
42x4 × 16′
42x4 × 20′
322x6 × 12′
142x6 × 20′
22x8 × 8′
12x8 × 20′
2PT 2x4 × 10′
2PT 2x4 × 16′
1PT 2x4 × 20′
247/16" OSB wall sheathing, 4×8 (10% waste)
161/2" OSB roof sheathing, 4×8 (15% waste)
15bundles shingles (4.3 squares + 10%)
2rolls synthetic underlayment
4.51cubic yards concrete (+10%)
32hurricane ties, rafter to plate

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A22x641"Header plysquare; two plies with a 1/2" plywood spacer
B42x639-1/2"Header plysquare; two plies with a 1/2" plywood spacer
C12x4236-1/2"Top platesquare ends; laps the next piece at the corner
D1PT 2x4101"Bottom platesquare ends; laps the next piece at the corner
E1PT 2x497-1/2"Bottom platesquare ends; laps the next piece at the corner
F82x492-5/8"Studsquare both ends
G62x492-5/8"King studsquare both ends
H62x481"Jack studsquare both ends
J22x436-1/2"Rough sillsquare both ends
K82x431"Cripplesquare both ends
L62x46-1/8"Cripplesquare both ends
M1PT 2x4188-1/2"Bottom platesquare ends; laps the next piece at the corner
N12x4188-1/2"Top platesquare ends; laps the next piece at the corner
P132x492-5/8"Studsquare both ends
Q22x875-1/2"Header plysquare; two plies with a 1/2" plywood spacer
R1PT 2x4236-1/2"Bottom platesquare ends; laps the next piece at the corner
S12x4236-1/2"Top platesquare ends; laps the next piece at the corner
T122x492-5/8"Studsquare both ends
U22x492-5/8"King studsquare both ends
V22x481"Jack studsquare both ends
W12x472-1/2"Rough sillsquare both ends
X62x431"Cripplesquare both ends
Y42x44-3/8"Cripplesquare both ends
Z1PT 2x4188-1/2"Bottom platesquare ends; laps the next piece at the corner
AA12x4188-1/2"Top platesquare ends; laps the next piece at the corner
AB132x492-5/8"Studsquare both ends
AC22x4236-1/2"Cap platelaps over the next wall at the corner
AD22x4188-1/2"Cap platelaps over the next wall at the corner
AE12x8240"Ridge boardsquare both ends
AF322x6132-9/16"Common rafterplumb cut 8/12 at the ridge; birdsmouth seat 1-1/2", heel 1"; tail plumb cut 12" past the wall
AG142x6192"Rafter tietop corners cut to 8/12
AH22x461-7/8"Gable studtop cut 8/12 (33.7°), long point up
AJ42x452-13/16"Gable studtop cut 8/12 (33.7°), long point up
AK42x442-3/16"Gable studtop cut 8/12 (33.7°), long point up
AL42x431-1/2"Gable studtop cut 8/12 (33.7°), long point up
AM42x420-13/16"Gable studtop cut 8/12 (33.7°), long point up
AN42x410-3/16"Gable studtop cut 8/12 (33.7°), long point up

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Pour the slab

    Pour the slab

    • Form, gravel, pour a 4" slab with a thickened edge.
    • Anchor bolts 6" from every plate end and every 6 ft.

    floatlevel

  2. Step 2: Build the front wall

    Build the front wall

    A ×2 2x6 41"B ×4 2x6 39-1/2"C ×1 2x4 236-1/2"D ×1 2x4 101"E ×1 2x4 97-1/2"F ×8 2x4 92-5/8"G ×6 2x4 92-5/8"H ×6 2x4 81"J ×2 2x4 36-1/2"K ×8 2x4 31"L ×6 2x4 6-1/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 127-1/4" · 143-1/4" · 159-1/4" · 175-1/4" · 191-1/4" · 207-1/4" · 223-1/4" · 235"
    • Frame the 38" × 82-1/2" door and the 36-1/2" × 48-1/2" window and the 36-1/2" × 48-1/2" window: kings, jacks, header.
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  3. Step 3: Build the right wall

    Build the right wall

    M ×1 2x4 188-1/2"N ×1 2x4 188-1/2"P ×13 2x4 92-5/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 127-1/4" · 143-1/4" · 159-1/4" · 175-1/4" · 187"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  4. Step 4: Build the back wall

    Build the back wall

    Q ×2 2x8 75-1/2"R ×1 2x4 236-1/2"S ×1 2x4 236-1/2"T ×12 2x4 92-5/8"U ×2 2x4 92-5/8"V ×2 2x4 81"W ×1 2x4 72-1/2"X ×6 2x4 31"Y ×4 2x4 4-3/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 127-1/4" · 143-1/4" · 159-1/4" · 175-1/4" · 191-1/4" · 207-1/4" · 223-1/4" · 235"
    • Frame the 72-1/2" × 48-1/2" window: kings, jacks, header.
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  5. Step 5: Build the left wall

    Build the left wall

    Z ×1 2x4 188-1/2"AA ×1 2x4 188-1/2"AB ×13 2x4 92-5/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 127-1/4" · 143-1/4" · 159-1/4" · 175-1/4" · 187"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  6. Step 6: Lap the cap plates

    Lap the cap plates

    AC ×2 2x4 236-1/2"AD ×2 2x4 188-1/2"

    • Cap plates overlap every corner. That ties the walls into one box.
    • Nails every 16", two at each lap.

    hammer

  7. Step 7: Raise the ridge

    Raise the ridge

    AE ×1 2x8 240"

    • Ridge AE on temporary posts at the height shown.
    • Plumb and brace before any rafters.

    levelclamps

  8. Step 8: Set the rafters

    Set the rafters

    AF ×32 2x6 132-9/16"

    • Cut ONE pattern rafter. Check it in three places. Then cut the rest.
    • Every 16", over the studs.
    • Hurricane tie every rafter to the plate.

    speed squaresawdrill

  9. Step 9: Tie the rafters

    Tie the rafters

    AG ×14 2x6 192"

    • A tie beside every rafter pair, on the cap plates.
    • Nail each end to its rafter.

    hammer

  10. Step 10: Fill the gable ends

    Fill the gable ends

    AH ×2 2x4 61-7/8"AJ ×4 2x4 52-13/16"AK ×4 2x4 42-3/16"AL ×4 2x4 31-1/2"AM ×4 2x4 20-13/16"AN ×4 2x4 10-3/16"

    • Studs every 16" from the cap up to the rafter.
    • Measure each in place. Long point up.

    speed squaresaw

  11. Step 11: Sheath the walls

    Sheath the walls

    • Sheets vertical, edges on studs, 1/8" gaps.
    • Nails 6" on edges, 12" in the middle. Cut out the openings after.

    sawnailerchalk line

  12. Step 12: Sheath the roof

    Sheath the roof

    • Long edge across the rafters, H-clips between, rows staggered.
    • Drip edge, underlayment, drip edge, shingles.

    sawnailer

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 185 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 186 pieces trace a chain of contact down to the foundation.
✓ Rafters 2x6 44% used
2x6 SPF #2, span 7.94 ft, w = 53 plf total / 37 plf live
Bending: M = wL²/8 = 5043 in·lb → fb = M/S = 667 psi ≤ F'b = 1504 psi  (44% used)
Shear: fv = 1.5V/A = 39 psi ≤ F'v = 155 psi  (25% used)
Deflection: 5wL⁴/384EI = 0.115" ≤ L/240 = 0.397"  (29% used)
✓ Header over door (front) 2x6 36% used
2-ply 2x6 SPF #2, span 3.42 ft, w = 360 plf total / 252 plf live
Bending: M = wL²/8 = 6307 in·lb → fb = M/S = 417 psi ≤ F'b = 1308 psi  (32% used)
Shear: fv = 1.5V/A = 56 psi ≤ F'v = 155 psi  (36% used)
Deflection: 5wL⁴/384EI = 0.013" ≤ L/240 = 0.171"  (8% used)
✓ Header over window (front) 2x6 35% used
2-ply 2x6 SPF #2, span 3.29 ft, w = 360 plf total / 252 plf live
Bending: M = wL²/8 = 5854 in·lb → fb = M/S = 387 psi ≤ F'b = 1308 psi  (30% used)
Shear: fv = 1.5V/A = 54 psi ≤ F'v = 155 psi  (35% used)
Deflection: 5wL⁴/384EI = 0.011" ≤ L/240 = 0.165"  (7% used)
✓ Header over window (front) 2x6 35% used
2-ply 2x6 SPF #2, span 3.29 ft, w = 360 plf total / 252 plf live
Bending: M = wL²/8 = 5854 in·lb → fb = M/S = 387 psi ≤ F'b = 1308 psi  (30% used)
Shear: fv = 1.5V/A = 54 psi ≤ F'v = 155 psi  (35% used)
Deflection: 5wL⁴/384EI = 0.011" ≤ L/240 = 0.165"  (7% used)
✓ Studs (front wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 480 lb  (17% used)
✓ Header over window (back) 2x8 67% used
2-ply 2x8 SPF #2, span 6.29 ft, w = 360 plf total / 252 plf live
Bending: M = wL²/8 = 21386 in·lb → fb = M/S = 814 psi ≤ F'b = 1208 psi  (67% used)
Shear: fv = 1.5V/A = 78 psi ≤ F'v = 155 psi  (50% used)
Deflection: 5wL⁴/384EI = 0.067" ≤ L/240 = 0.315"  (21% used)
✓ Studs (back wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 480 lb  (17% used)
✓ Birdsmouth notch shear (rafters) 2x6 46% used
Heel cut 1" plumb leaves dn = 4.67" of the 5.5" depth over the bearing.
NDS 3.4.3.2 notched end: V'r = 2/3 · F'v · b · dn · (dn/d)² = 522 lb ≥ reaction 240 lb (46% used)

Roof: 10 psf dead + snow 0.7 × 40 = 28 psf. Rafter ties at every rafter pair stop the walls spreading (a ridge board is not a beam). Nail per IRC Table R802.5.2.

Questions

How much lumber does a 16x20 Cabin need?

76 2x4 × 8′, 4 2x4 × 16′, 4 2x4 × 20′, 32 2x6 × 12′, 14 2x6 × 20′, 2 2x8 × 8′, 1 2x8 × 20′, 2 PT 2x4 × 10′, 2 PT 2x4 × 16′, 1 PT 2x4 × 20′. 24 7/16" OSB wall sheathing, 4×8 (10% waste); 16 1/2" OSB roof sheathing, 4×8 (15% waste); 15 bundles shingles (4.3 squares + 10%).

What size rafters does a 16x20 Cabin need?

2x6 at 16″ on center, using 44% of their capacity at 40 psf ground snow. The bending, shear and deflection numbers are in the proof section.

How tall is it?

13′ 11-5/16″ at the peak, measured from the ground.

Do I need a permit for a 16x20 Cabin?

It covers 320 sq ft. The model code (IRC R105.2) exempts one-story detached accessory buildings up to 200 sq ft, and many towns set the line at 120 sq ft. Call your building department before you dig.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

14×20 Cabin280 sq ft · 175 pcs · 12 steps16×24 Cabin384 sq ft · 195 pcs · 12 steps12×20 Cabin240 sq ft · 167 pcs · 12 steps12×16 Cabin192 sq ft · 153 pcs · 12 steps20×24 Cabin480 sq ft · 207 pcs · 12 steps