Design your own

16×24 Workshop Plans

This 16×24 workshop sits on a 4″ concrete slab, with 9′ walls, a 6/12 gable roof and a peak of 13′ 4-7/8″. The 74″-wide double door opening gets a doubled header sized for the roof load above it. Rafters are 2x4 at 16″ on center. All 181 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 146 boards plus sheet goods and hardware.

Footprint16′ 0″ × 24′ 0″
Area384 sq ft
Height13′ 4-7/8″
Lumber181 pcs
Steps12
Checks9 pass

Open in the builderJump to the steps

3D model of the 16×24 workshop framing

Shopping list

162x4 × 8′
592x4 × 10′
382x4 × 12′
42x4 × 16′
42x4 × 20′
22x6 × 8′
182x6 × 20′
2PT 2x4 × 10′
2PT 2x4 × 16′
1PT 2x4 × 20′
287/16" OSB wall sheathing, 4×8 (10% waste)
181/2" OSB roof sheathing, 4×8 (15% waste)
16bundles shingles (4.8 squares + 10%)
2rolls synthetic underlayment
5.4cubic yards concrete (+10%)
38hurricane ties, rafter to plate

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A22x677"Header plysquare; two plies with a 1/2" plywood spacer
B12x4284-1/2"Top platesquare ends; laps the next piece at the corner
C1PT 2x4107"Bottom platesquare ends; laps the next piece at the corner
D142x4104-5/8"Studsquare both ends
E22x4104-5/8"King studsquare both ends
F1PT 2x4103-1/2"Bottom platesquare ends; laps the next piece at the corner
G22x481"Jack studsquare both ends
H52x418-1/8"Cripplesquare both ends
J22x639-1/2"Header plysquare; two plies with a 1/2" plywood spacer
K1PT 2x4188-1/2"Bottom platesquare ends; laps the next piece at the corner
L12x4188-1/2"Top platesquare ends; laps the next piece at the corner
M102x4104-5/8"Studsquare both ends
N22x4104-5/8"King studsquare both ends
P22x479"Jack studsquare both ends
Q32x441"Cripplesquare both ends
R12x436-1/2"Rough sillsquare both ends
S32x420-1/8"Cripplesquare both ends
T1PT 2x4284-1/2"Bottom platesquare ends; laps the next piece at the corner
U12x4284-1/2"Top platesquare ends; laps the next piece at the corner
V192x4104-5/8"Studsquare both ends
W22x639-1/2"Header plysquare; two plies with a 1/2" plywood spacer
X1PT 2x4188-1/2"Bottom platesquare ends; laps the next piece at the corner
Y12x4188-1/2"Top platesquare ends; laps the next piece at the corner
Z102x4104-5/8"Studsquare both ends
AA22x4104-5/8"King studsquare both ends
AB22x479"Jack studsquare both ends
AC32x441"Cripplesquare both ends
AD12x436-1/2"Rough sillsquare both ends
AE32x420-1/8"Cripplesquare both ends
AF22x4284-1/2"Cap platelaps over the next wall at the corner
AG22x4188-1/2"Cap platelaps over the next wall at the corner
AH12x6288"Ridge boardsquare both ends
AJ382x4121-11/16"Common rafterplumb cut 6/12 at the ridge; birdsmouth seat 1-1/2", heel 3/4"; tail plumb cut 12" past the wall
AK172x6192"Rafter tietop corners cut to 6/12
AL22x445-5/16"Gable studtop cut 6/12 (26.6°), long point up
AM42x439-5/8"Gable studtop cut 6/12 (26.6°), long point up
AN42x431-5/8"Gable studtop cut 6/12 (26.6°), long point up
AP42x423-5/8"Gable studtop cut 6/12 (26.6°), long point up
AQ42x415-5/8"Gable studtop cut 6/12 (26.6°), long point up
AR42x47-5/8"Gable studtop cut 6/12 (26.6°), long point up

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Pour the slab

    Pour the slab

    • Form, gravel, pour a 4" slab with a thickened edge.
    • Anchor bolts 6" from every plate end and every 6 ft.

    floatlevel

  2. Step 2: Build the front wall

    Build the front wall

    A ×2 2x6 77"B ×1 2x4 284-1/2"C ×1 2x4 107"D ×14 2x4 104-5/8"E ×2 2x4 104-5/8"F ×1 2x4 103-1/2"G ×2 2x4 81"H ×5 2x4 18-1/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 127-1/4" · 143-1/4" · 159-1/4" · 175-1/4" · 191-1/4" · 207-1/4" · 223-1/4" · 239-1/4" · 255-1/4" · 271-1/4" · 283"
    • Frame the 74" × 82-1/2" door: kings, jacks, header.
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  3. Step 3: Build the right wall

    Build the right wall

    J ×2 2x6 39-1/2"K ×1 2x4 188-1/2"L ×1 2x4 188-1/2"M ×10 2x4 104-5/8"N ×2 2x4 104-5/8"P ×2 2x4 79"Q ×3 2x4 41"R ×1 2x4 36-1/2"S ×3 2x4 20-1/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 127-1/4" · 143-1/4" · 159-1/4" · 175-1/4" · 187"
    • Frame the 36-1/2" × 36-1/2" window: kings, jacks, header.
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  4. Step 4: Build the back wall

    Build the back wall

    T ×1 2x4 284-1/2"U ×1 2x4 284-1/2"V ×19 2x4 104-5/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 127-1/4" · 143-1/4" · 159-1/4" · 175-1/4" · 191-1/4" · 207-1/4" · 223-1/4" · 239-1/4" · 255-1/4" · 271-1/4" · 283"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  5. Step 5: Build the left wall

    Build the left wall

    W ×2 2x6 39-1/2"X ×1 2x4 188-1/2"Y ×1 2x4 188-1/2"Z ×10 2x4 104-5/8"AA ×2 2x4 104-5/8"AB ×2 2x4 79"AC ×3 2x4 41"AD ×1 2x4 36-1/2"AE ×3 2x4 20-1/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): 0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 95-1/4" · 111-1/4" · 127-1/4" · 143-1/4" · 159-1/4" · 175-1/4" · 187"
    • Frame the 36-1/2" × 36-1/2" window: kings, jacks, header.
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  6. Step 6: Lap the cap plates

    Lap the cap plates

    AF ×2 2x4 284-1/2"AG ×2 2x4 188-1/2"

    • Cap plates overlap every corner. That ties the walls into one box.
    • Nails every 16", two at each lap.

    hammer

  7. Step 7: Raise the ridge

    Raise the ridge

    AH ×1 2x6 288"

    • Ridge AH on temporary posts at the height shown.
    • Plumb and brace before any rafters.

    levelclamps

  8. Step 8: Set the rafters

    Set the rafters

    AJ ×38 2x4 121-11/16"

    • Cut ONE pattern rafter. Check it in three places. Then cut the rest.
    • Every 16", over the studs.
    • Hurricane tie every rafter to the plate.

    speed squaresawdrill

  9. Step 9: Tie the rafters

    Tie the rafters

    AK ×17 2x6 192"

    • A tie beside every rafter pair, on the cap plates.
    • Nail each end to its rafter.

    hammer

  10. Step 10: Fill the gable ends

    Fill the gable ends

    AL ×2 2x4 45-5/16"AM ×4 2x4 39-5/8"AN ×4 2x4 31-5/8"AP ×4 2x4 23-5/8"AQ ×4 2x4 15-5/8"AR ×4 2x4 7-5/8"

    • Studs every 16" from the cap up to the rafter.
    • Measure each in place. Long point up.

    speed squaresaw

  11. Step 11: Sheath the walls

    Sheath the walls

    • Sheets vertical, edges on studs, 1/8" gaps.
    • Nails 6" on edges, 12" in the middle. Cut out the openings after.

    sawnailerchalk line

  12. Step 12: Sheath the roof

    Sheath the roof

    • Long edge across the rafters, H-clips between, rows staggered.
    • Drip edge, underlayment, drip edge, shingles.

    sawnailer

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 187 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 188 pieces trace a chain of contact down to the foundation.
✓ Rafters 2x4 84% used
2x4 SPF #2, span 7.94 ft, w = 43 plf total / 28 plf live
Bending: M = wL²/8 = 4055 in·lb → fb = M/S = 1324 psi ≤ F'b = 1736 psi  (76% used)
Shear: fv = 1.5V/A = 49 psi ≤ F'v = 155 psi  (31% used)
Deflection: 5wL⁴/384EI = 0.333" ≤ L/240 = 0.397"  (84% used)
✓ Header over door (front) 2x6 90% used
2-ply 2x6 SPF #2, span 6.42 ft, w = 290 plf total / 189 plf live
Bending: M = wL²/8 = 17887 in·lb → fb = M/S = 1183 psi ≤ F'b = 1308 psi  (90% used)
Shear: fv = 1.5V/A = 84 psi ≤ F'v = 155 psi  (54% used)
Deflection: 5wL⁴/384EI = 0.124" ≤ L/240 = 0.321"  (39% used)
✓ Studs (front wall) 60% used
2x4 SPF #2, unbraced length 104.6" (le/d = 29.9 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 469 psi → Cp = 0.286
Capacity = Cp·F*c·A = 2281 lb ≥ load 386 lb  (17% used)
✓ Header over window (right) 2x6 1% used
2-ply 2x6 SPF #2, span 3.29 ft, w = 6 plf total / 4 plf live
Bending: M = wL²/8 = 98 in·lb → fb = M/S = 6 psi ≤ F'b = 1308 psi  (0% used)
Shear: fv = 1.5V/A = 1 psi ≤ F'v = 155 psi  (1% used)
Deflection: 5wL⁴/384EI = 0.000" ≤ L/240 = 0.165"  (0% used)
✓ Studs (back wall) 60% used
2x4 SPF #2, unbraced length 104.6" (le/d = 29.9 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 469 psi → Cp = 0.286
Capacity = Cp·F*c·A = 2281 lb ≥ load 386 lb  (17% used)
✓ Header over window (left) 2x6 1% used
2-ply 2x6 SPF #2, span 3.29 ft, w = 6 plf total / 4 plf live
Bending: M = wL²/8 = 98 in·lb → fb = M/S = 6 psi ≤ F'b = 1308 psi  (0% used)
Shear: fv = 1.5V/A = 1 psi ≤ F'v = 155 psi  (1% used)
Deflection: 5wL⁴/384EI = 0.000" ≤ L/240 = 0.165"  (0% used)
✓ Birdsmouth notch shear (rafters) 2x4 67% used
Heel cut 3/4" plumb leaves dn = 2.83" of the 3.5" depth over the bearing.
NDS 3.4.3.2 notched end: V'r = 2/3 · F'v · b · dn · (dn/d)² = 287 lb ≥ reaction 193 lb (67% used)

Roof: 10 psf dead + snow 0.7 × 30 = 21 psf. Rafter ties at every rafter pair stop the walls spreading (a ridge board is not a beam). Nail per IRC Table R802.5.2.

Questions

How much lumber does a 16x24 Workshop need?

16 2x4 × 8′, 59 2x4 × 10′, 38 2x4 × 12′, 4 2x4 × 16′, 4 2x4 × 20′, 2 2x6 × 8′, 18 2x6 × 20′, 2 PT 2x4 × 10′, 2 PT 2x4 × 16′, 1 PT 2x4 × 20′. 28 7/16" OSB wall sheathing, 4×8 (10% waste); 18 1/2" OSB roof sheathing, 4×8 (15% waste); 16 bundles shingles (4.8 squares + 10%).

What size rafters does a 16x24 Workshop need?

2x4 at 16″ on center, using 84% of their capacity at 30 psf ground snow. The bending, shear and deflection numbers are in the proof section.

How tall is it?

13′ 4-7/8″ at the peak, measured from the ground.

Do I need a permit for a 16x24 Workshop?

It covers 384 sq ft. The model code (IRC R105.2) exempts one-story detached accessory buildings up to 200 sq ft, and many towns set the line at 120 sq ft. Call your building department before you dig.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

14×24 Workshop336 sq ft · 177 pcs · 12 steps12×20 Workshop240 sq ft · 154 pcs · 12 steps12×16 Workshop192 sq ft · 141 pcs · 12 steps