Design your own

8′ Octagon Gazebo Plans

This 8′ octagon gazebo has 8 posts, a doubled ring beam and a 8/12 pyramid roof that peaks at 11′ 3-1/2″. Hip rafters run from each corner to a center hub, with 2x6 rafters filling each side. All 105 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 62 boards plus sheet goods and hardware.

Footprint8-sided, 3′ 4″ sides
Area54 sq ft
Height11′ 3-1/2″
Lumber105 pcs
Steps8
Checks8 pass

Open in the builderJump to the steps

3D model of the 8′ octagon gazebo framing

Shopping list

142x2 × 8′
72x4 × 8′
162x6 × 8′
162x8 × 8′
16x6 × 8′
8PT 4x4 × 8′
41/2" OSB roof sheathing, 4×8 (15% waste)
4bundles shingles (1.0 squares + 10%)
1rolls synthetic underlayment
0.84cubic yards concrete (+10%)
8post bases + post caps
16hurricane ties, rafter to plate
8steel straps across the ring-beam mitres (rating in the proof)

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A8PT 4x491-5/8"Corner postsquare both ends
B82x640"Ring beam plymitre both ends 22.5°
C82x638-3/4"Ring beam plymitre both ends 22.5°
D16x614-7/16"Hub block8-sided, 8-11/16" across the flats (glue up from 2x stock); top cut to a point at 8/12
E162x876"Hip rafter (2-ply)two identical plies nailed face to face; plumb cuts at 7.39/12 (31.6°); top edge dropped 3/8"; birdsmouth seat 3-7/8"
F82x670-1/2"Centre raftertop: plumb cut 8/12 with 22.5° cheek cuts both sides (it sits between two hips); birdsmouth seat 1-1/2", heel 1"; tail plumb cut 12" past the wall
G72x434"Bottom railsquare both ends
H72x434"Top railsquare both ends
J422x226"Balustersquare both ends

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Pour the slab

    Pour the slab

    • Form, gravel, pour a 4" slab with a thickened edge.
    • Anchor bolts 6" from every plate end and every 6 ft.

    floatlevel

  2. Step 2: Stand the corner posts

    Stand the corner posts

    A ×8 4x4 91-5/8"

    • Posts A at every corner, outside faces flush with the edge.
    • Plumb on two faces. Brace both ways.

    leveldrill

  3. Step 3: Put the ring beam on

    Put the ring beam on

    B ×8 2x6 40"C ×8 2x6 38-3/4"

    • Mitre every ply at the angle in the box. Nail plies in pairs.
    • Set on the posts. Strap every mitre.

    mitre sawhammer

  4. Step 4: Make the hub

    Make the hub

    D ×1 6x6 14-7/16"

    • Cut hub D: 8-sided, 8-11/16" across the flats (glue up from 2x stock); top cut to a point at 8/12.
    • Hold it at the peak on a temporary centre post.

    sawclamps

  5. Step 5: Set the hip rafters

    Set the hip rafters

    E ×16 2x8 76"

    • Cut ONE hip E. Test it, then cut the rest.
    • Corner to hub. Set opposite pairs so the hub stays centred.

    speed squaresawdrill

  6. Step 6: Fill in the rafters

    Fill in the rafters

    F ×8 2x6 70-1/2"

    • Cut ONE pattern rafter. Check it in three places. Then cut the rest.
    • Jacks get a side (cheek) cut where they meet a hip.
    • Hurricane tie every rafter to the plate.

    speed squaresawdrill

  7. Step 7: Sheath the roof

    Sheath the roof

    • Long edge across the rafters, H-clips between, rows staggered.
    • Drip edge, underlayment, drip edge, shingles.

    sawnailer

  8. Step 8: Add the railing

    Add the railing

    G ×7 2x4 34"H ×7 2x4 34"J ×42 2x2 26"

    • Posts first. Then bottom and top rails.
    • Balusters with a 3-7/8" spacer block between each.
    • Cap last.

    drillsawlevel

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 105 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 106 pieces trace a chain of contact down to the foundation.
✓ Rafters 2x6 16% used
2x6 SPF #2, span 4.02 ft, w = 66 plf total / 42 plf live
Bending: M = wL²/8 = 1604 in·lb → fb = M/S = 212 psi ≤ F'b = 1504 psi  (14% used)
Shear: fv = 1.5V/A = 24 psi ≤ F'v = 155 psi  (16% used)
Deflection: 5wL⁴/384EI = 0.009" ≤ L/240 = 0.201"  (4% used)
Bending alone allows 2x4; stepped up to 2x6 so the birdsmouth notches pass shear.
✓ Ring beams (2-ply) 2x6 17% used
2-ply 2x6 SPF #2, span 3.33 ft, w = 177 plf total / 113 plf live
Bending: M = wL²/8 = 2949 in·lb → fb = M/S = 195 psi ≤ F'b = 1308 psi  (15% used)
Shear: fv = 1.5V/A = 27 psi ≤ F'v = 155 psi  (17% used)
Deflection: 5wL⁴/384EI = 0.005" ≤ L/240 = 0.167"  (3% used)
✓ Corner posts 4x4 52% used
4x4 SPF #2, height 7.64 ft, le/d = 26.2 ≤ 50
FcE = 612 psi → Cp = 0.361 → capacity 6732 lb ≥ load 331 lb (5% used)
✓ Outward thrust at the eaves (ring tension) 50% used
The roof pushes each corner outward 249 lb (three-hinged arch: W·run / 2·rise).
The ring beam carries T = H / (2·sin(180°/8)) = 325 lb of tension through every mitre.
So every mitre gets a steel strap rated ≥ 350 lb allowable tension (in the shopping list).
✓ Birdsmouth notch shear (hip rafters) 2x8 33% used
Heel cut 3-5/16" plumb leaves dn = 4.45" of the 7.25" depth over the bearing.
NDS 3.4.3.2 notched end: V'r = 2/3 · F'v · b · dn · (dn/d)² = 521 lb ≥ reaction 172 lb (33% used)
✓ Birdsmouth notch shear (rafters) 2x6 16% used
Heel cut 1" plumb leaves dn = 4.67" of the 5.5" depth over the bearing.
NDS 3.4.3.2 notched end: V'r = 2/3 · F'v · b · dn · (dn/d)² = 522 lb ≥ reaction 83 lb (16% used)

Roof: 10 psf dead + snow 0.7 × 30 = 21 psf.

Questions

How much lumber does a 8′ Octagon Gazebo need?

14 2x2 × 8′, 7 2x4 × 8′, 16 2x6 × 8′, 16 2x8 × 8′, 1 6x6 × 8′, 8 PT 4x4 × 8′. 4 1/2" OSB roof sheathing, 4×8 (15% waste); 4 bundles shingles (1.0 squares + 10%); 1 rolls synthetic underlayment.

What size rafters does a 8′ Octagon Gazebo need?

2x6 at 24″ on center, using 16% of their capacity at 30 psf ground snow. The bending, shear and deflection numbers are in the proof section.

How tall is it?

11′ 3-1/2″ at the peak, measured from the ground.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

10′ Octagon Gazebo82 sq ft · 119 pcs · 8 steps12′ Octagon Gazebo119 sq ft · 149 pcs · 8 steps14′ Octagon Gazebo162 sq ft · 163 pcs · 8 steps16′ Octagon Gazebo212 sq ft · 170 pcs · 8 steps8′ Hexagon Gazebo56 sq ft · 92 pcs · 8 steps10′ Hexagon Gazebo87 sq ft · 114 pcs · 8 steps