10×10 Deck Plans, 30″ High
This 10′ × 10′ deck stands 30″ off the ground on posts on concrete footings. Joists are 2x6 at 16″ on center, carried by doubled 2x12 beams. The stairs and the 36″ guard are drawn and checked. All 54 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 49 boards plus sheet goods and hardware.

Shopping list
Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.
Parts and cut list
Cut every part, then pencil its letter on it. The steps call parts by letter.
| Part | Qty | Size | Length | Piece | How to cut |
|---|---|---|---|---|---|
| A | 4 | PT 4x4 | 12-1/4" | Post | square both ends |
| B | 4 | PT 2x12 | 112" | Beam ply | square; 2 plies nailed together, 10d every 16" staggered |
| C | 4 | PT 2x6 | 118-1/2" | Rim joist | square ends; laps the next piece at the corner |
| D | 9 | PT 2x6 | 117" | Floor joist | square both ends |
| E | 22 | PT 5/4x6 | 120" | Deck board | square both ends |
| F | 1 | PT 2x12 | 48" | Stair hanger board | square; bolt to the rim |
| G | 4 | PT 2x12 | 37-3/16" | Stair stringer | 3 notches: rise 7-1/2", run 10-1/4"; plumb cut at the top, level cut at the bottom |
| H | 6 | PT 2x6 | 48" | Stair tread | square both ends |
Step by step
New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

Dig and pour the footings
- Stake out 4 post spots exactly where the picture shows.
- Dig each hole Ø24" wide, below your frost line.
- Pour concrete. Set a post base in each one, all level with a string line.
shovelstring linelevel

Stand the posts
A ×4 4x4 12-1/4"
- Cut posts A to the length in the box.
- Fix each to its base. Plumb on two faces. Brace both ways.
sawleveldrill

Set the beams
B ×4 2x12 112"
- Nail each pair of B plies together, 10d nails every 16", staggered.
- Crown up. Set on the posts and fix with post caps.
sawhammerlevel

Frame the floor
C ×4 2x6 118-1/2"D ×9 2x6 117"
- Rims C around the outside, corners lapped as drawn.
- Mark joists every 16" along the rims.
- Joists D between the rims: 3 nails each end.
- Measure both diagonals. Equal = square.
sawhammersquaretape

Lay the decking
E ×22 5/4x6 120"
- Start at the front edge. 1/8" gap between boards (a 16d nail).
- Two screws into every joist. Board ends only land on a joist.
drillsawchalk line

Build the stairs
F ×1 2x12 48"G ×4 2x12 37-3/16"H ×6 2x6 48"
- Bolt the hanger board to the rim.
- Lay out ONE stringer with a framing square. Test it. Cut the rest.
- Stringers on the pad. Two screws per tread board per stringer.
framing squaresawdrill
The proof
Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.
✓ No two pieces occupy the same space
All 54 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 59 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x6 61% used
2x6 SPF #2, span 7.75 ft, w = 67 plf total / 53 plf live Bending: M = wL²/8 = 6006 in·lb → fb = M/S = 794 psi ≤ F'b = 1308 psi (61% used) Shear: fv = 1.5V/A = 47 psi ≤ F'v = 135 psi (35% used) Deflection: 5wL⁴/384EI = 0.149" ≤ L/360 = 0.258" (58% used)
✓ Deck beams (2-ply) 2x12 97% used
2-ply 2x12 SPF #2, span 9.04 ft, w = 438 plf total / 350 plf live Bending: M = wL²/8 = 53650 in·lb → fb = M/S = 848 psi ≤ F'b = 875 psi (97% used) Shear: fv = 1.5V/A = 88 psi ≤ F'v = 135 psi (65% used) Deflection: 5wL⁴/384EI = 0.106" ≤ L/360 = 0.301" (35% used)
✓ Floor posts 4x4 25% used
4x4 SPF #2, height 1.02 ft, le/d = 3.5 ≤ 50 FcE = 34222 psi → Cp = 0.992 → capacity 16072 lb ≥ load 3956 lb (25% used)
✓ Footings 87% used
Load 4106 lb ÷ 1500 psf presumptive soil bearing = 394 in² needed 24" round footing = 452 in² (87% used). Bottom below your local frost depth.
✓ Stair geometry 97% used
4 equal risers of 7-1/2" (max 7-3/4"), 3 treads: 10-1/4" run + 1" nosing (min 10"). Notched 2x12 stringers keep 5-3/16" of wood under each notch (min 5").
✓ Stair stringers 12% used
2x12 (5.20" deep after notching) SPF #2, span 2.56 ft, w = 67 plf total / 53 plf live Bending: M = wL²/8 = 657 in·lb → fb = M/S = 97 psi ≤ F'b = 875 psi (11% used) Shear: fv = 1.5V/A = 16 psi ≤ F'v = 135 psi (12% used) Deflection: 5wL⁴/384EI = 0.002" ≤ L/360 = 0.085" (2% used)
Floor: 40 psf live + 10 psf dead. Footings bear on undisturbed soil below frost depth (1500 psf soil assumed). Post bases and post caps at every post.
Questions
How much lumber does a 10x10 Deck need?
3 PT 2x12 × 8′, 4 PT 2x12 × 10′, 6 PT 2x6 × 8′, 13 PT 2x6 × 10′, 1 PT 4x4 × 8′, 22 PT 5/4x6 × 12′. 0.6 cubic yards concrete (+10%); 4 post bases + post caps; 1 boxes 2-1/2" deck screws (350/box).
What size joists does a 10x10 Deck need?
2x6 at 16″ on center, using 61% of capacity at 40 psf live load.
How big do the footings need to be?
24″ round, 4 of them, bearing below your local frost line. That assumes 1,500 psf soil.
Does a 10x10 Deck need a railing?
Not by code at 30″; guards are required above 30″. You can add one in the builder.
Can I change the size or add a door?
Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.
10×10 Deck
10×10 Deck
10×10 Ground-Level Deck
8×10 Deck
8×10 Deck
8×10 Deck