Design your own

10×10 Deck Plans, 48″ High

This 10′ × 10′ deck stands 48″ off the ground on posts on concrete footings. Joists are 2x6 at 16″ on center, carried by doubled 2x12 beams. The stairs and the 36″ guard are drawn and checked. All 164 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 103 boards plus sheet goods and hardware.

Footprint10′ 0″ × 10′ 0″
Area100 sq ft
Height7′ 0″
Lumber164 pcs
Steps7
Checks9 pass

Open in the builderJump to the steps

3D model of the 10×10 deck framing

Shopping list

5PT 2x12 × 8′
4PT 2x12 × 10′
24PT 2x2 × 8′
12PT 2x4 × 8′
12PT 2x6 × 8′
13PT 2x6 × 10′
3PT 2x6 × 12′
8PT 4x4 × 8′
22PT 5/4x6 × 12′
0.6cubic yards concrete (+10%)
4post bases + post caps
1boxes 2-1/2" deck screws (350/box)

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A4PT 4x430-1/4"Postsquare both ends
B4PT 2x12112"Beam plysquare; 2 plies nailed together, 10d every 16" staggered
C4PT 2x6118-1/2"Rim joistsquare ends; laps the next piece at the corner
D9PT 2x6117"Floor joistsquare both ends
E22PT 5/4x6120"Deck boardsquare both ends
F3PT 2x6120"Rail capflat on the post tops; mitred at corners
G2PT 2x632-1/2"Rail capflat on the post tops; mitred at corners
H6PT 2x454-3/4"Bottom railsquare both ends
J6PT 2x454-3/4"Top railsquare both ends
K2PT 2x425-1/2"Bottom railsquare both ends
L2PT 2x425-1/2"Top railsquare both ends
M13PT 4x441"Guard postsquare; through-bolt to the rim, two 1/2" bolts
N70PT 2x224"Balustersquare both ends
P4PT 2x1273-3/16"Stair stringer6 notches: rise 6-7/8", run 10-1/4"; plumb cut at the top, level cut at the bottom
Q1PT 2x1248"Stair hanger boardsquare; bolt to the rim
R12PT 2x648"Stair treadsquare both ends

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Dig and pour the footings

    Dig and pour the footings

    • Stake out 4 post spots exactly where the picture shows.
    • Dig each hole Ø24" wide, below your frost line.
    • Pour concrete. Set a post base in each one, all level with a string line.

    shovelstring linelevel

  2. Step 2: Stand the posts

    Stand the posts

    A ×4 4x4 30-1/4"

    • Cut posts A to the length in the box.
    • Fix each to its base. Plumb on two faces. Brace both ways.

    sawleveldrill

  3. Step 3: Set the beams

    Set the beams

    B ×4 2x12 112"

    • Nail each pair of B plies together, 10d nails every 16", staggered.
    • Crown up. Set on the posts and fix with post caps.

    sawhammerlevel

  4. Step 4: Frame the floor

    Frame the floor

    C ×4 2x6 118-1/2"D ×9 2x6 117"

    • Rims C around the outside, corners lapped as drawn.
    • Mark joists every 16" along the rims.
    • Joists D between the rims: 3 nails each end.
    • Measure both diagonals. Equal = square.

    sawhammersquaretape

  5. Step 5: Lay the decking

    Lay the decking

    E ×22 5/4x6 120"

    • Start at the front edge. 1/8" gap between boards (a 16d nail).
    • Two screws into every joist. Board ends only land on a joist.

    drillsawchalk line

  6. Step 6: Add the railing

    Add the railing

    F ×3 2x6 120"G ×2 2x6 32-1/2"H ×6 2x4 54-3/4"J ×6 2x4 54-3/4"K ×2 2x4 25-1/2"L ×2 2x4 25-1/2"M ×13 4x4 41"N ×70 2x2 24"

    • Posts first. Then bottom and top rails.
    • Balusters with a 3-7/8" spacer block between each.
    • Cap last.

    drillsawlevel

  7. Step 7: Build the stairs

    Build the stairs

    P ×4 2x12 73-3/16"Q ×1 2x12 48"R ×12 2x6 48"

    • Bolt the hanger board to the rim.
    • Lay out ONE stringer with a framing square. Test it. Cut the rest.
    • Stringers on the pad. Two screws per tread board per stringer.

    framing squaresawdrill

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 164 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 169 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x6 61% used
2x6 SPF #2, span 7.75 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 6006 in·lb → fb = M/S = 794 psi ≤ F'b = 1308 psi  (61% used)
Shear: fv = 1.5V/A = 47 psi ≤ F'v = 135 psi  (35% used)
Deflection: 5wL⁴/384EI = 0.149" ≤ L/360 = 0.258"  (58% used)
✓ Deck beams (2-ply) 2x12 97% used
2-ply 2x12 SPF #2, span 9.04 ft, w = 438 plf total / 350 plf live
Bending: M = wL²/8 = 53650 in·lb → fb = M/S = 848 psi ≤ F'b = 875 psi  (97% used)
Shear: fv = 1.5V/A = 88 psi ≤ F'v = 135 psi  (65% used)
Deflection: 5wL⁴/384EI = 0.106" ≤ L/360 = 0.301"  (35% used)
✓ Floor posts 4x4 26% used
4x4 SPF #2, height 2.52 ft, le/d = 8.6 ≤ 50
FcE = 5612 psi → Cp = 0.946 → capacity 15322 lb ≥ load 3956 lb (26% used)
✓ Footings 87% used
Load 4106 lb ÷ 1500 psf presumptive soil bearing = 394 in² needed
24" round footing = 452 in² (87% used). Bottom below your local frost depth.
✓ Guard geometry 90% used
36" guard height. Baluster gaps under 4", so a 4" ball cannot pass. Bottom gap 3-1/2".
Guard-post bolting follows the AWC DCA 6 detail; that connection is not calculated here.
✓ Stair geometry 88% used
7 equal risers of 6-7/8" (max 7-3/4"), 6 treads: 10-1/4" run + 1" nosing (min 10").
Notched 2x12 stringers keep 5-9/16" of wood under each notch (min 5").
✓ Stair stringers 39% used
2x12 (5.55" deep after notching) SPF #2, span 5.13 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 2627 in·lb → fb = M/S = 341 psi ≤ F'b = 875 psi  (39% used)
Shear: fv = 1.5V/A = 31 psi ≤ F'v = 135 psi  (23% used)
Deflection: 5wL⁴/384EI = 0.028" ≤ L/360 = 0.171"  (16% used)

Floor: 40 psf live + 10 psf dead. Footings bear on undisturbed soil below frost depth (1500 psf soil assumed). Post bases and post caps at every post.

Questions

How much lumber does a 10x10 Deck need?

5 PT 2x12 × 8′, 4 PT 2x12 × 10′, 24 PT 2x2 × 8′, 12 PT 2x4 × 8′, 12 PT 2x6 × 8′, 13 PT 2x6 × 10′, 3 PT 2x6 × 12′, 8 PT 4x4 × 8′, 22 PT 5/4x6 × 12′. 0.6 cubic yards concrete (+10%); 4 post bases + post caps; 1 boxes 2-1/2" deck screws (350/box).

What size joists does a 10x10 Deck need?

2x6 at 16″ on center, using 61% of capacity at 40 psf live load.

How big do the footings need to be?

24″ round, 4 of them, bearing below your local frost line. That assumes 1,500 psf soil.

Does a 10x10 Deck need a railing?

Yes. Any deck surface more than 30″ above grade needs a guard at least 36″ high, and this plan includes one.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

10×10 Deck100 sq ft · 54 pcs · 6 steps10×10 Deck100 sq ft · 160 pcs · 7 steps10×10 Ground-Level Deck100 sq ft · 37 pcs · 3 steps8×10 Deck80 sq ft · 49 pcs · 6 steps8×10 Deck80 sq ft · 147 pcs · 7 steps8×10 Deck80 sq ft · 151 pcs · 7 steps