Design your own

14′ Hexagon Gazebo Plans

This 14′ hexagon gazebo has 6 posts, a doubled ring beam and a 8/12 pyramid roof that peaks at 13′ 5-7/16″. Hip rafters run from each corner to a center hub, with 2x8 rafters filling each side. All 144 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 88 boards plus sheet goods and hardware.

Footprint6-sided, 8′ 1″ sides
Area170 sq ft
Height13′ 5-7/16″
Lumber144 pcs
Steps8
Checks8 pass

Open in the builderJump to the steps

3D model of the 14′ hexagon gazebo framing

Shopping list

122x10 × 12′
292x2 × 8′
102x4 × 8′
182x8 × 8′
122x8 × 10′
16x6 × 8′
6PT 4x4 × 8′
101/2" OSB roof sheathing, 4×8 (15% waste)
9bundles shingles (2.7 squares + 10%)
1rolls synthetic underlayment
2.45cubic yards concrete (+10%)
6post bases + post caps
24hurricane ties, rafter to plate
6steel straps across the ring-beam mitres (rating in the proof)

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A6PT 4x489-7/8"Corner postsquare both ends
B62x897"Ring beam plymitre both ends 30.0°
C62x895-1/4"Ring beam plymitre both ends 30.0°
D16x615-3/4"Hub block6-sided, 6-1/4" across the flats (glue up from 2x stock); top cut to a point at 8/12
E122x10129-3/4"Hip rafter (2-ply)two identical plies nailed face to face; plumb cuts at 6.93/12 (30.0°); top edge dropped 1/2"; birdsmouth seat 4-5/16"
F62x8115-7/8"Centre raftertop: plumb cut 8/12 with 30.0° cheek cuts both sides (it sits between two hips); birdsmouth seat 1-1/2", heel 1"; tail plumb cut 12" past the wall
G122x868-3/16"Jack raftertop: plumb cut 8/12 plus a 30.0° cheek cut against the hip; birdsmouth seat 1-1/2", heel 1"; tail plumb cut 12" past the wall
H52x490-7/16"Bottom railsquare both ends
J52x490-7/16"Top railsquare both ends
K852x226"Balustersquare both ends

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Pour the slab

    Pour the slab

    • Form, gravel, pour a 4" slab with a thickened edge.
    • Anchor bolts 6" from every plate end and every 6 ft.

    floatlevel

  2. Step 2: Stand the corner posts

    Stand the corner posts

    A ×6 4x4 89-7/8"

    • Posts A at every corner, outside faces flush with the edge.
    • Plumb on two faces. Brace both ways.

    leveldrill

  3. Step 3: Put the ring beam on

    Put the ring beam on

    B ×6 2x8 97"C ×6 2x8 95-1/4"

    • Mitre every ply at the angle in the box. Nail plies in pairs.
    • Set on the posts. Strap every mitre.

    mitre sawhammer

  4. Step 4: Make the hub

    Make the hub

    D ×1 6x6 15-3/4"

    • Cut hub D: 6-sided, 6-1/4" across the flats (glue up from 2x stock); top cut to a point at 8/12.
    • Hold it at the peak on a temporary centre post.

    sawclamps

  5. Step 5: Set the hip rafters

    Set the hip rafters

    E ×12 2x10 129-3/4"

    • Cut ONE hip E. Test it, then cut the rest.
    • Corner to hub. Set opposite pairs so the hub stays centred.

    speed squaresawdrill

  6. Step 6: Fill in the rafters

    Fill in the rafters

    F ×6 2x8 115-7/8"G ×12 2x8 68-3/16"

    • Cut ONE pattern rafter. Check it in three places. Then cut the rest.
    • Jacks get a side (cheek) cut where they meet a hip.
    • Hurricane tie every rafter to the plate.

    speed squaresawdrill

  7. Step 7: Sheath the roof

    Sheath the roof

    • Long edge across the rafters, H-clips between, rows staggered.
    • Drip edge, underlayment, drip edge, shingles.

    sawnailer

  8. Step 8: Add the railing

    Add the railing

    H ×5 2x4 90-7/16"J ×5 2x4 90-7/16"K ×85 2x2 26"

    • Posts first. Then bottom and top rails.
    • Balusters with a 3-7/8" spacer block between each.
    • Cap last.

    drillsawlevel

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 144 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 145 pieces trace a chain of contact down to the foundation.
✓ Rafters 2x8 27% used
2x8 SPF #2, span 7.00 ft, w = 66 plf total / 42 plf live
Bending: M = wL²/8 = 4854 in·lb → fb = M/S = 369 psi ≤ F'b = 1389 psi  (27% used)
Shear: fv = 1.5V/A = 32 psi ≤ F'v = 155 psi  (21% used)
Deflection: 5wL⁴/384EI = 0.034" ≤ L/240 = 0.350"  (10% used)
Bending alone allows 2x4; stepped up to 2x8 so the birdsmouth notches pass shear.
✓ Ring beams (2-ply) 2x8 68% used
2-ply 2x8 SPF #2, span 8.08 ft, w = 220 plf total / 140 plf live
Bending: M = wL²/8 = 21531 in·lb → fb = M/S = 819 psi ≤ F'b = 1208 psi  (68% used)
Shear: fv = 1.5V/A = 61 psi ≤ F'v = 155 psi  (39% used)
Deflection: 5wL⁴/384EI = 0.101" ≤ L/240 = 0.404"  (25% used)
✓ Corner posts 4x4 51% used
4x4 SPF #2, height 7.49 ft, le/d = 25.7 ≤ 50
FcE = 636 psi → Cp = 0.373 → capacity 6959 lb ≥ load 1201 lb (17% used)
✓ Outward thrust at the eaves (ring tension) 50% used
The roof pushes each corner outward 901 lb (three-hinged arch: W·run / 2·rise).
The ring beam carries T = H / (2·sin(180°/6)) = 901 lb of tension through every mitre.
So every mitre gets a steel strap rated ≥ 950 lb allowable tension (in the shopping list).
✓ Birdsmouth notch shear (hip rafters) 2x10 69% used
Heel cut 3-7/16" plumb leaves dn = 6.25" of the 9.25" depth over the bearing.
NDS 3.4.3.2 notched end: V'r = 2/3 · F'v · b · dn · (dn/d)² = 885 lb ≥ reaction 608 lb (69% used)
✓ Birdsmouth notch shear (rafters) 2x8 26% used
Heel cut 1" plumb leaves dn = 6.42" of the 7.25" depth over the bearing.
NDS 3.4.3.2 notched end: V'r = 2/3 · F'v · b · dn · (dn/d)² = 781 lb ≥ reaction 206 lb (26% used)

Roof: 10 psf dead + snow 0.7 × 30 = 21 psf.

Questions

How much lumber does a 14′ Hexagon Gazebo need?

12 2x10 × 12′, 29 2x2 × 8′, 10 2x4 × 8′, 18 2x8 × 8′, 12 2x8 × 10′, 1 6x6 × 8′, 6 PT 4x4 × 8′. 10 1/2" OSB roof sheathing, 4×8 (15% waste); 9 bundles shingles (2.7 squares + 10%); 1 rolls synthetic underlayment.

What size rafters does a 14′ Hexagon Gazebo need?

2x8 at 24″ on center, using 27% of their capacity at 30 psf ground snow. The bending, shear and deflection numbers are in the proof section.

How tall is it?

13′ 5-7/16″ at the peak, measured from the ground.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

8′ Octagon Gazebo54 sq ft · 105 pcs · 8 steps10′ Octagon Gazebo82 sq ft · 119 pcs · 8 steps12′ Octagon Gazebo119 sq ft · 149 pcs · 8 steps14′ Octagon Gazebo162 sq ft · 163 pcs · 8 steps16′ Octagon Gazebo212 sq ft · 170 pcs · 8 steps8′ Hexagon Gazebo56 sq ft · 92 pcs · 8 steps