Design your own

8×10 Ground-Level Deck Plans

This 8′ × 10′ deck stands at ground level on skids. Joists are 2x6 at 16″ on center, resting on the skids. All 32 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 32 boards plus sheet goods and hardware.

Footprint8′ 0″ × 10′ 0″
Area80 sq ft
Height1′ 0″
Lumber32 pcs
Steps3
Checks3 pass

Open in the builderJump to the steps

3D model of the 8×10 ground-level deck framing

Shopping list

11PT 2x6 × 8′
2PT 2x6 × 10′
2PT 4x6 × 12′
17PT 5/4x6 × 12′
1boxes 2-1/2" deck screws (350/box)

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A2PT 4x6120"Skidsquare both ends
B2PT 2x6118-1/2"Rim joistsquare ends; laps the next piece at the corner
C2PT 2x694-1/2"Rim joistsquare ends; laps the next piece at the corner
D9PT 2x693"Floor joistsquare both ends
E17PT 5/4x6120"Deck boardsquare both ends

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Lay the skids

    Lay the skids

    A ×2 4x6 120"

    • Compact 4" of gravel 2 ft past the footprint.
    • Lay A parallel, level within 1/4".

    rakelevel

  2. Step 2: Frame the floor

    Frame the floor

    B ×2 2x6 118-1/2"C ×2 2x6 94-1/2"D ×9 2x6 93"

    • Rims B, C around the outside, corners lapped as drawn.
    • Mark joists every 16" along the rims.
    • Joists D between the rims: 3 nails each end.
    • Measure both diagonals. Equal = square.

    sawhammersquaretape

  3. Step 3: Lay the decking

    Lay the decking

    E ×17 5/4x6 120"

    • Start at the front edge. 1/8" gap between boards (a 16d nail).
    • Two screws into every joist. Board ends only land on a joist.

    drillsawchalk line

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 32 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 32 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x6 60% used
2x6 SPF #2, span 7.71 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 5942 in·lb → fb = M/S = 786 psi ≤ F'b = 1308 psi  (60% used)
Shear: fv = 1.5V/A = 47 psi ≤ F'v = 135 psi  (35% used)
Deflection: 5wL⁴/384EI = 0.146" ≤ L/360 = 0.257"  (57% used)

Floor: 40 psf live + 10 psf dead. 2 skids on 4" of compacted gravel, level within 1/4".

Questions

How much lumber does a 8x10 Ground-Level Deck need?

11 PT 2x6 × 8′, 2 PT 2x6 × 10′, 2 PT 4x6 × 12′, 17 PT 5/4x6 × 12′. 1 boxes 2-1/2" deck screws (350/box).

What size joists does a 8x10 Ground-Level Deck need?

2x6 at 16″ on center, using 60% of capacity at 40 psf live load.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

8×10 Deck80 sq ft · 49 pcs · 6 steps8×10 Deck80 sq ft · 147 pcs · 7 steps8×10 Deck80 sq ft · 151 pcs · 7 steps8×8 Deck64 sq ft · 47 pcs · 6 steps8×8 Deck64 sq ft · 135 pcs · 7 steps8×8 Deck64 sq ft · 139 pcs · 7 steps