10′ Hexagon Garden Room Plans
This 10′ hexagon garden room sits on pressure-treated skids on gravel, with 8′ walls, a 6/12 pyramid roof and a peak of 12′ 2-11/16″. The 38″-wide door opening gets a doubled header sized for the roof load above it. Rafters are 2x6 at 16″ on center. All 120 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 100 boards plus sheet goods and hardware.

Shopping list
Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.
Parts and cut list
Cut every part, then pencil its letter on it. The steps call parts by letter.
| Part | Qty | Size | Length | Piece | How to cut |
|---|---|---|---|---|---|
| A | 2 | PT 4x6 | 73-9/16" | Skid | square both ends |
| B | 4 | PT 2x8 | 117-3/8" | Floor joist | square both ends |
| C | 1 | PT 2x8 | 107-7/16" | Floor joist | ends cut 60.0° off square |
| D | 1 | PT 2x8 | 90-1/8" | Floor joist | ends cut 60.0° off square |
| E | 6 | PT 2x8 | 69-1/2" | Rim joist | ends cut to the 120.0° corner (30.0° mitre) |
| F | 1 | PT 2x8 | 52" | Floor joist | ends cut 60.0° off square |
| G | 1 | PT 2x8 | 34-11/16" | Floor joist | ends cut 60.0° off square |
| H | 2 | 2x6 | 41" | Header ply | square; two plies with a 1/2" plywood spacer |
| J | 2 | 2x4 | 92-5/8" | Stud | square both ends |
| K | 2 | 2x4 | 92-5/8" | King stud | square both ends |
| L | 2 | 2x4 | 81" | Jack stud | square both ends |
| M | 1 | 2x4 | 69-1/2" | Top plate | ends cut to the 120.0° corner (30.0° mitre) |
| N | 1 | 2x4 | 17-3/4" | Bottom plate | ends cut to the 120.0° corner (30.0° mitre) |
| P | 1 | 2x4 | 13-3/4" | Bottom plate | ends cut to the 120.0° corner (30.0° mitre) |
| Q | 3 | 2x4 | 6-1/8" | Cripple | square both ends |
| R | 5 | 2x4 | 92-5/8" | Stud | square both ends |
| S | 1 | 2x4 | 69-1/2" | Bottom plate | ends cut to the 120.0° corner (30.0° mitre) |
| T | 1 | 2x4 | 69-1/2" | Top plate | ends cut to the 120.0° corner (30.0° mitre) |
| U | 2 | 2x6 | 33-1/2" | Header ply | square; two plies with a 1/2" plywood spacer |
| V | 2 | 2x4 | 92-5/8" | Stud | square both ends |
| W | 2 | 2x4 | 92-5/8" | King stud | square both ends |
| X | 2 | 2x4 | 71" | Jack stud | square both ends |
| Y | 1 | 2x4 | 69-1/2" | Bottom plate | ends cut to the 120.0° corner (30.0° mitre) |
| Z | 1 | 2x4 | 69-1/2" | Top plate | ends cut to the 120.0° corner (30.0° mitre) |
| AA | 3 | 2x4 | 33" | Cripple | square both ends |
| AB | 1 | 2x4 | 30-1/2" | Rough sill | square both ends |
| AC | 2 | 2x4 | 16-1/8" | Cripple | square both ends |
| AD | 5 | 2x4 | 92-5/8" | Stud | square both ends |
| AE | 1 | 2x4 | 69-1/2" | Bottom plate | ends cut to the 120.0° corner (30.0° mitre) |
| AF | 1 | 2x4 | 69-1/2" | Top plate | ends cut to the 120.0° corner (30.0° mitre) |
| AG | 2 | 2x6 | 33-1/2" | Header ply | square; two plies with a 1/2" plywood spacer |
| AH | 2 | 2x4 | 92-5/8" | Stud | square both ends |
| AJ | 2 | 2x4 | 92-5/8" | King stud | square both ends |
| AK | 2 | 2x4 | 71" | Jack stud | square both ends |
| AL | 1 | 2x4 | 69-1/2" | Bottom plate | ends cut to the 120.0° corner (30.0° mitre) |
| AM | 1 | 2x4 | 69-1/2" | Top plate | ends cut to the 120.0° corner (30.0° mitre) |
| AN | 3 | 2x4 | 33" | Cripple | square both ends |
| AP | 1 | 2x4 | 30-1/2" | Rough sill | square both ends |
| AQ | 2 | 2x4 | 16-1/8" | Cripple | square both ends |
| AR | 5 | 2x4 | 92-5/8" | Stud | square both ends |
| AS | 1 | 2x4 | 69-1/2" | Bottom plate | ends cut to the 120.0° corner (30.0° mitre) |
| AT | 1 | 2x4 | 69-1/2" | Top plate | ends cut to the 120.0° corner (30.0° mitre) |
| AU | 6 | 2x4 | 69-1/2" | Cap plate | laps over the next wall at the corner |
| AV | 1 | 6x6 | 12-7/16" | Hub block | 6-sided, 6-1/4" across the flats (glue up from 2x stock); top cut to a point at 6/12 |
| AW | 12 | 2x8 | 90-9/16" | Hip rafter (2-ply) | two identical plies nailed face to face; plumb cuts at 5.20/12 (23.4°); top edge dropped 3/8"; birdsmouth seat 4-15/16" |
| AX | 6 | 2x6 | 79-7/16" | Centre rafter | top: plumb cut 6/12 with 30.0° cheek cuts both sides (it sits between two hips); birdsmouth seat 1-1/2", heel 3/4"; tail plumb cut 12" past the wall |
| AY | 12 | 2x6 | 50-9/16" | Jack rafter | top: plumb cut 6/12 plus a 30.0° cheek cut against the hip; birdsmouth seat 1-1/2", heel 3/4"; tail plumb cut 12" past the wall |
Step by step
New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

Lay the skids
A ×2 4x6 73-9/16"
- Compact 4" of gravel 2 ft past the footprint.
- Lay A parallel, level within 1/4".
rakelevel

Frame the floor
B ×4 2x8 117-3/8"C ×1 2x8 107-7/16"D ×1 2x8 90-1/8"E ×6 2x8 69-1/2"F ×1 2x8 52"G ×1 2x8 34-11/16"
- Rims E around the outside, corners lapped as drawn.
- Mark joists every 16" along the rims.
- Joists B, C, D, F, G between the rims: 3 nails each end.
- Measure both diagonals. Equal = square.
sawhammersquaretape

Lay the subfloor
- Long edge across the joists, rows staggered 4 ft.
- Glue on every joist. Screws 6" on edges, 12" in the middle.
drillsawchalk line

Build the side 1 wall
H ×2 2x6 41"J ×2 2x4 92-5/8"K ×2 2x4 92-5/8"L ×2 2x4 81"M ×1 2x4 69-1/2"N ×1 2x4 17-3/4"P ×1 2x4 13-3/4"Q ×3 2x4 6-1/8"
- Lay bottom and top plates side by side on the floor.
- Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-15/16"
- Frame the 38" × 82-1/2" door: kings, jacks, header.
- Nail 2 × 16d through the plates into each stud end.
- Equal diagonals, stand it up, plumb, brace.
sawhammerlevelsquare

Build the side 2 wall
R ×5 2x4 92-5/8"S ×1 2x4 69-1/2"T ×1 2x4 69-1/2"
- Lay bottom and top plates side by side on the floor.
- Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-15/16"
- Nail 2 × 16d through the plates into each stud end.
- Equal diagonals, stand it up, plumb, brace.
sawhammerlevelsquare

Build the side 3 wall
U ×2 2x6 33-1/2"V ×2 2x4 92-5/8"W ×2 2x4 92-5/8"X ×2 2x4 71"Y ×1 2x4 69-1/2"Z ×1 2x4 69-1/2"AA ×3 2x4 33"AB ×1 2x4 30-1/2"AC ×2 2x4 16-1/8"
- Lay bottom and top plates side by side on the floor.
- Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-15/16"
- Frame the 30-1/2" × 36-1/2" window: kings, jacks, header.
- Nail 2 × 16d through the plates into each stud end.
- Equal diagonals, stand it up, plumb, brace.
sawhammerlevelsquare

Build the side 4 wall
AD ×5 2x4 92-5/8"AE ×1 2x4 69-1/2"AF ×1 2x4 69-1/2"
- Lay bottom and top plates side by side on the floor.
- Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-15/16"
- Nail 2 × 16d through the plates into each stud end.
- Equal diagonals, stand it up, plumb, brace.
sawhammerlevelsquare

Build the side 5 wall
AG ×2 2x6 33-1/2"AH ×2 2x4 92-5/8"AJ ×2 2x4 92-5/8"AK ×2 2x4 71"AL ×1 2x4 69-1/2"AM ×1 2x4 69-1/2"AN ×3 2x4 33"AP ×1 2x4 30-1/2"AQ ×2 2x4 16-1/8"
- Lay bottom and top plates side by side on the floor.
- Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-15/16"
- Frame the 30-1/2" × 36-1/2" window: kings, jacks, header.
- Nail 2 × 16d through the plates into each stud end.
- Equal diagonals, stand it up, plumb, brace.
sawhammerlevelsquare

Build the side 6 wall
AR ×5 2x4 92-5/8"AS ×1 2x4 69-1/2"AT ×1 2x4 69-1/2"
- Lay bottom and top plates side by side on the floor.
- Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-15/16"
- Nail 2 × 16d through the plates into each stud end.
- Equal diagonals, stand it up, plumb, brace.
sawhammerlevelsquare

Lap the cap plates
AU ×6 2x4 69-1/2"
- Cap plates overlap every corner. That ties the walls into one box.
- Nails every 16", two at each lap.
hammer

Make the hub
AV ×1 6x6 12-7/16"
- Cut hub AV: 6-sided, 6-1/4" across the flats (glue up from 2x stock); top cut to a point at 6/12.
- Hold it at the peak on a temporary centre post.
sawclamps

Set the hip rafters
AW ×12 2x8 90-9/16"
- Cut ONE hip AW. Test it, then cut the rest.
- Corner to hub. Set opposite pairs so the hub stays centred.
speed squaresawdrill

Fill in the rafters
AX ×6 2x6 79-7/16"AY ×12 2x6 50-9/16"
- Cut ONE pattern rafter. Check it in three places. Then cut the rest.
- Jacks get a side (cheek) cut where they meet a hip.
- Hurricane tie every rafter to the plate.
speed squaresawdrill

Sheath the walls
- Sheets vertical, edges on studs, 1/8" gaps.
- Nails 6" on edges, 12" in the middle. Cut out the openings after.
sawnailerchalk line

Sheath the roof
- Long edge across the rafters, H-clips between, rows staggered.
- Drip edge, underlayment, drip edge, shingles.
sawnailer
The proof
Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.
✓ No two pieces occupy the same space
All 132 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 132 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x8 60% used
2x8 SPF #2, span 9.74 ft, w = 67 plf total / 53 plf live Bending: M = wL²/8 = 9486 in·lb → fb = M/S = 722 psi ≤ F'b = 1208 psi (60% used) Shear: fv = 1.5V/A = 45 psi ≤ F'v = 135 psi (33% used) Deflection: 5wL⁴/384EI = 0.162" ≤ L/360 = 0.325" (50% used)
✓ Rafters 2x6 14% used
2x6 SPF #2, span 5.02 ft, w = 43 plf total / 28 plf live Bending: M = wL²/8 = 1619 in·lb → fb = M/S = 214 psi ≤ F'b = 1504 psi (14% used) Shear: fv = 1.5V/A = 20 psi ≤ F'v = 155 psi (13% used) Deflection: 5wL⁴/384EI = 0.014" ≤ L/240 = 0.251" (5% used) Bending alone allows 2x4; stepped up to 2x6 so the birdsmouth notches pass shear.
✓ Header over door (side 1) 2x6 19% used
2-ply 2x6 SPF #2, span 3.42 ft, w = 194 plf total / 126 plf live Bending: M = wL²/8 = 3390 in·lb → fb = M/S = 224 psi ≤ F'b = 1308 psi (17% used) Shear: fv = 1.5V/A = 30 psi ≤ F'v = 155 psi (19% used) Deflection: 5wL⁴/384EI = 0.007" ≤ L/240 = 0.171" (4% used)
✓ Studs (side 1 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50) F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355 Capacity = Cp·F*c·A = 2831 lb ≥ load 258 lb (9% used)
✓ Studs (side 2 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50) F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355 Capacity = Cp·F*c·A = 2831 lb ≥ load 258 lb (9% used)
✓ Header over window (side 3) 2x6 16% used
2-ply 2x6 SPF #2, span 2.79 ft, w = 194 plf total / 126 plf live Bending: M = wL²/8 = 2263 in·lb → fb = M/S = 150 psi ≤ F'b = 1308 psi (11% used) Shear: fv = 1.5V/A = 25 psi ≤ F'v = 155 psi (16% used) Deflection: 5wL⁴/384EI = 0.003" ≤ L/240 = 0.140" (2% used)
✓ Studs (side 3 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50) F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355 Capacity = Cp·F*c·A = 2831 lb ≥ load 258 lb (9% used)
✓ Studs (side 4 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50) F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355 Capacity = Cp·F*c·A = 2831 lb ≥ load 258 lb (9% used)
✓ Header over window (side 5) 2x6 16% used
2-ply 2x6 SPF #2, span 2.79 ft, w = 194 plf total / 126 plf live Bending: M = wL²/8 = 2263 in·lb → fb = M/S = 150 psi ≤ F'b = 1308 psi (11% used) Shear: fv = 1.5V/A = 25 psi ≤ F'v = 155 psi (16% used) Deflection: 5wL⁴/384EI = 0.003" ≤ L/240 = 0.140" (2% used)
✓ Studs (side 5 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50) F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355 Capacity = Cp·F*c·A = 2831 lb ≥ load 258 lb (9% used)
✓ Studs (side 6 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50) F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355 Capacity = Cp·F*c·A = 2831 lb ≥ load 258 lb (9% used)
✓ Birdsmouth notch shear (hip rafters) 2x8 46% used
Heel cut 2-7/8" plumb leaves dn = 4.61" of the 7.25" depth over the bearing. NDS 3.4.3.2 notched end: V'r = 2/3 · F'v · b · dn · (dn/d)² = 579 lb ≥ reaction 268 lb (46% used)
✓ Birdsmouth notch shear (rafters) 2x6 18% used
Heel cut 3/4" plumb leaves dn = 4.83" of the 5.5" depth over the bearing. NDS 3.4.3.2 notched end: V'r = 2/3 · F'v · b · dn · (dn/d)² = 578 lb ≥ reaction 104 lb (18% used)
Roof: 10 psf dead + snow 0.7 × 30 = 21 psf. Floor: 40 psf live + 10 psf dead. 2 skids on 4" of compacted gravel, level within 1/4".
Questions
How much lumber does a 10′ Hexagon Garden Room need?
54 2x4 × 8′, 18 2x6 × 8′, 12 2x8 × 8′, 1 6x6 × 8′, 8 PT 2x8 × 8′, 5 PT 2x8 × 10′, 2 PT 4x6 × 8′. 6 3/4" T&G plywood subfloor, 4×8; 11 7/16" OSB wall sheathing, 4×8 (10% waste); 6 1/2" OSB roof sheathing, 4×8 (15% waste).
What size rafters does a 10′ Hexagon Garden Room need?
2x6 at 16″ on center, using 14% of their capacity at 30 psf ground snow. The bending, shear and deflection numbers are in the proof section.
What size joists does a 10′ Hexagon Garden Room need?
2x8 at 16″ on center, using 60% of capacity at 40 psf live load.
How tall is it?
12′ 2-11/16″ at the peak, measured from the ground.
Do I need a permit for a 10′ Hexagon Garden Room?
It covers 87 sq ft. The model code (IRC R105.2) exempts one-story detached accessory buildings up to 200 sq ft, and many towns set the line at 120 sq ft. Call your building department before you dig.
Can I change the size or add a door?
Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.
12′ Hexagon Garden Room
14′ Hexagon Garden Room
12′ Octagon Garden Room
14′ Octagon Garden Room