Design your own

14′ Octagon Garden Room Plans

This 14′ octagon garden room sits on pressure-treated skids on gravel, with 8′ walls, a 6/12 pyramid roof and a peak of 13′ 3/4″. The 38″-wide door opening gets a doubled header sized for the roof load above it. Rafters are 2x6 at 16″ on center. All 162 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 141 boards plus sheet goods and hardware.

Footprint8-sided, 5′ 9-1/2″ sides
Area162 sq ft
Height13′ 3/4″
Lumber162 pcs
Steps17
Checks18 pass

Open in the builderJump to the steps

3D model of the 14′ octagon garden room framing

Shopping list

732x4 × 8′
202x6 × 8′
82x6 × 10′
162x8 × 10′
16x6 × 8′
11PT 2x6 × 8′
2PT 2x6 × 10′
1PT 2x6 × 12′
6PT 2x6 × 14′
2PT 4x6 × 8′
1PT 4x6 × 16′
93/4" T&G plywood subfloor, 4×8
147/16" OSB wall sheathing, 4×8 (10% waste)
91/2" OSB roof sheathing, 4×8 (15% waste)
8bundles shingles (2.4 squares + 10%)
1rolls synthetic underlayment
32hurricane ties, rafter to plate

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A1PT 4x6167-13/16"Skidsquare both ends
B2PT 4x676-1/2"Skidsquare both ends
C4PT 2x6164-13/16"Floor joistsquare both ends
D1PT 2x6162-3/4"Floor joistends cut 45.0° off square
E1PT 2x6146-5/16"Floor joistends cut 45.0° off square
F1PT 2x6130-3/4"Floor joistends cut 45.0° off square
G1PT 2x6114-5/16"Floor joistends cut 45.0° off square
H1PT 2x698-3/4"Floor joistends cut 45.0° off square
J1PT 2x682-5/16"Floor joistends cut 45.0° off square
K2PT 2x671-1/4"Floor joistends cut 45.0° off square
L8PT 2x670-3/8"Rim joistends cut to the 135.0° corner (22.5° mitre)
M22x641"Header plysquare; two plies with a 1/2" plywood spacer
N22x492-5/8"Studsquare both ends
P22x492-5/8"King studsquare both ends
Q22x481"Jack studsquare both ends
R12x471-9/16"Top plateends cut to the 135.0° corner (22.5° mitre)
S12x419-1/4"Bottom plateends cut to the 135.0° corner (22.5° mitre)
T12x414-5/16"Bottom plateends cut to the 135.0° corner (22.5° mitre)
U32x46-1/8"Cripplesquare both ends
V52x492-5/8"Studsquare both ends
W12x471-9/16"Bottom plateends cut to the 135.0° corner (22.5° mitre)
X12x471-9/16"Top plateends cut to the 135.0° corner (22.5° mitre)
Y22x633-1/2"Header plysquare; two plies with a 1/2" plywood spacer
Z22x492-5/8"Studsquare both ends
AA22x492-5/8"King studsquare both ends
AB12x471-9/16"Bottom plateends cut to the 135.0° corner (22.5° mitre)
AC12x471-9/16"Top plateends cut to the 135.0° corner (22.5° mitre)
AD22x471"Jack studsquare both ends
AE32x433"Cripplesquare both ends
AF12x430-1/2"Rough sillsquare both ends
AG22x416-1/8"Cripplesquare both ends
AH52x492-5/8"Studsquare both ends
AJ12x471-9/16"Bottom plateends cut to the 135.0° corner (22.5° mitre)
AK12x471-9/16"Top plateends cut to the 135.0° corner (22.5° mitre)
AL22x633-1/2"Header plysquare; two plies with a 1/2" plywood spacer
AM22x492-5/8"Studsquare both ends
AN22x492-5/8"King studsquare both ends
AP12x471-9/16"Bottom plateends cut to the 135.0° corner (22.5° mitre)
AQ12x471-9/16"Top plateends cut to the 135.0° corner (22.5° mitre)
AR22x471"Jack studsquare both ends
AS32x433"Cripplesquare both ends
AT12x430-1/2"Rough sillsquare both ends
AU22x416-1/8"Cripplesquare both ends
AV52x492-5/8"Studsquare both ends
AW12x471-9/16"Bottom plateends cut to the 135.0° corner (22.5° mitre)
AX12x471-9/16"Top plateends cut to the 135.0° corner (22.5° mitre)
AY22x633-1/2"Header plysquare; two plies with a 1/2" plywood spacer
AZ22x492-5/8"Studsquare both ends
BA22x492-5/8"King studsquare both ends
BB12x471-9/16"Bottom plateends cut to the 135.0° corner (22.5° mitre)
BC12x471-9/16"Top plateends cut to the 135.0° corner (22.5° mitre)
BD22x471"Jack studsquare both ends
BE32x433"Cripplesquare both ends
BF12x430-1/2"Rough sillsquare both ends
BG22x416-1/8"Cripplesquare both ends
BH52x492-5/8"Studsquare both ends
BJ12x471-9/16"Bottom plateends cut to the 135.0° corner (22.5° mitre)
BK12x471-9/16"Top plateends cut to the 135.0° corner (22.5° mitre)
BL82x471-9/16"Cap platelaps over the next wall at the corner
BM16x613-3/16"Hub block8-sided, 8-11/16" across the flats (glue up from 2x stock); top cut to a point at 6/12
BN162x8112-7/8"Hip rafter (2-ply)two identical plies nailed face to face; plumb cuts at 5.54/12 (24.8°); top edge dropped 5/16"; birdsmouth seat 4-7/16"
BP82x6104-11/16"Centre raftertop: plumb cut 6/12 with 22.5° cheek cuts both sides (it sits between two hips); birdsmouth seat 1-1/2", heel 3/4"; tail plumb cut 12" past the wall
BQ162x664-7/16"Jack raftertop: plumb cut 6/12 plus a 22.5° cheek cut against the hip; birdsmouth seat 1-1/2", heel 3/4"; tail plumb cut 12" past the wall

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Lay the skids

    Lay the skids

    A ×1 4x6 167-13/16"B ×2 4x6 76-1/2"

    • Compact 4" of gravel 2 ft past the footprint.
    • Lay A, B parallel, level within 1/4".

    rakelevel

  2. Step 2: Frame the floor

    Frame the floor

    C ×4 2x6 164-13/16"D ×1 2x6 162-3/4"E ×1 2x6 146-5/16"F ×1 2x6 130-3/4"G ×1 2x6 114-5/16"H ×1 2x6 98-3/4"J ×1 2x6 82-5/16"K ×2 2x6 71-1/4"L ×8 2x6 70-3/8"

    • Rims L around the outside, corners lapped as drawn.
    • Mark joists every 16" along the rims.
    • Joists C, D, E, F, G, H, J, K between the rims: 3 nails each end.
    • Measure both diagonals. Equal = square.

    sawhammersquaretape

  3. Step 3: Lay the subfloor

    Lay the subfloor

    • Long edge across the joists, rows staggered 4 ft.
    • Glue on every joist. Screws 6" on edges, 12" in the middle.

    drillsawchalk line

  4. Step 4: Build the side 1 wall

    Build the side 1 wall

    M ×2 2x6 41"N ×2 2x4 92-5/8"P ×2 2x4 92-5/8"Q ×2 2x4 81"R ×1 2x4 71-9/16"S ×1 2x4 19-1/4"T ×1 2x4 14-5/16"U ×3 2x4 6-1/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/16"
    • Frame the 38" × 82-1/2" door: kings, jacks, header.
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  5. Step 5: Build the side 2 wall

    Build the side 2 wall

    V ×5 2x4 92-5/8"W ×1 2x4 71-9/16"X ×1 2x4 71-9/16"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/16"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  6. Step 6: Build the side 3 wall

    Build the side 3 wall

    Y ×2 2x6 33-1/2"Z ×2 2x4 92-5/8"AA ×2 2x4 92-5/8"AB ×1 2x4 71-9/16"AC ×1 2x4 71-9/16"AD ×2 2x4 71"AE ×3 2x4 33"AF ×1 2x4 30-1/2"AG ×2 2x4 16-1/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/16"
    • Frame the 30-1/2" × 36-1/2" window: kings, jacks, header.
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  7. Step 7: Build the side 4 wall

    Build the side 4 wall

    AH ×5 2x4 92-5/8"AJ ×1 2x4 71-9/16"AK ×1 2x4 71-9/16"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/16"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  8. Step 8: Build the side 5 wall

    Build the side 5 wall

    AL ×2 2x6 33-1/2"AM ×2 2x4 92-5/8"AN ×2 2x4 92-5/8"AP ×1 2x4 71-9/16"AQ ×1 2x4 71-9/16"AR ×2 2x4 71"AS ×3 2x4 33"AT ×1 2x4 30-1/2"AU ×2 2x4 16-1/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/16"
    • Frame the 30-1/2" × 36-1/2" window: kings, jacks, header.
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  9. Step 9: Build the side 6 wall

    Build the side 6 wall

    AV ×5 2x4 92-5/8"AW ×1 2x4 71-9/16"AX ×1 2x4 71-9/16"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/16"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  10. Step 10: Build the side 7 wall

    Build the side 7 wall

    AY ×2 2x6 33-1/2"AZ ×2 2x4 92-5/8"BA ×2 2x4 92-5/8"BB ×1 2x4 71-9/16"BC ×1 2x4 71-9/16"BD ×2 2x4 71"BE ×3 2x4 33"BF ×1 2x4 30-1/2"BG ×2 2x4 16-1/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/16"
    • Frame the 30-1/2" × 36-1/2" window: kings, jacks, header.
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  11. Step 11: Build the side 8 wall

    Build the side 8 wall

    BH ×5 2x4 92-5/8"BJ ×1 2x4 71-9/16"BK ×1 2x4 71-9/16"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/16"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  12. Step 12: Lap the cap plates

    Lap the cap plates

    BL ×8 2x4 71-9/16"

    • Cap plates overlap every corner. That ties the walls into one box.
    • Nails every 16", two at each lap.

    hammer

  13. Step 13: Make the hub

    Make the hub

    BM ×1 6x6 13-3/16"

    • Cut hub BM: 8-sided, 8-11/16" across the flats (glue up from 2x stock); top cut to a point at 6/12.
    • Hold it at the peak on a temporary centre post.

    sawclamps

  14. Step 14: Set the hip rafters

    Set the hip rafters

    BN ×16 2x8 112-7/8"

    • Cut ONE hip BN. Test it, then cut the rest.
    • Corner to hub. Set opposite pairs so the hub stays centred.

    speed squaresawdrill

  15. Step 15: Fill in the rafters

    Fill in the rafters

    BP ×8 2x6 104-11/16"BQ ×16 2x6 64-7/16"

    • Cut ONE pattern rafter. Check it in three places. Then cut the rest.
    • Jacks get a side (cheek) cut where they meet a hip.
    • Hurricane tie every rafter to the plate.

    speed squaresawdrill

  16. Step 16: Sheath the walls

    Sheath the walls

    • Sheets vertical, edges on studs, 1/8" gaps.
    • Nails 6" on edges, 12" in the middle. Cut out the openings after.

    sawnailerchalk line

  17. Step 17: Sheath the roof

    Sheath the roof

    • Long edge across the rafters, H-clips between, rows staggered.
    • Drip edge, underlayment, drip edge, shingles.

    sawnailer

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 179 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 179 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x6 47% used
2x6 SPF #2, span 6.85 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 4686 in·lb → fb = M/S = 620 psi ≤ F'b = 1308 psi  (47% used)
Shear: fv = 1.5V/A = 41 psi ≤ F'v = 135 psi  (31% used)
Deflection: 5wL⁴/384EI = 0.090" ≤ L/360 = 0.228"  (40% used)
✓ Rafters 2x6 28% used
2x6 SPF #2, span 6.99 ft, w = 43 plf total / 28 plf live
Bending: M = wL²/8 = 3146 in·lb → fb = M/S = 416 psi ≤ F'b = 1504 psi  (28% used)
Shear: fv = 1.5V/A = 27 psi ≤ F'v = 155 psi  (18% used)
Deflection: 5wL⁴/384EI = 0.052" ≤ L/240 = 0.350"  (15% used)
Bending alone allows 2x4; stepped up to 2x6 so the birdsmouth notches pass shear.
✓ Header over door (side 1) 2x6 26% used
2-ply 2x6 SPF #2, span 3.42 ft, w = 257 plf total / 168 plf live
Bending: M = wL²/8 = 4503 in·lb → fb = M/S = 298 psi ≤ F'b = 1308 psi  (23% used)
Shear: fv = 1.5V/A = 40 psi ≤ F'v = 155 psi  (26% used)
Deflection: 5wL⁴/384EI = 0.009" ≤ L/240 = 0.171"  (5% used)
✓ Studs (side 1 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 343 lb  (12% used)
✓ Studs (side 2 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 343 lb  (12% used)
✓ Header over window (side 3) 2x6 21% used
2-ply 2x6 SPF #2, span 2.79 ft, w = 257 plf total / 168 plf live
Bending: M = wL²/8 = 3006 in·lb → fb = M/S = 199 psi ≤ F'b = 1308 psi  (15% used)
Shear: fv = 1.5V/A = 33 psi ≤ F'v = 155 psi  (21% used)
Deflection: 5wL⁴/384EI = 0.004" ≤ L/240 = 0.140"  (3% used)
✓ Studs (side 3 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 343 lb  (12% used)
✓ Studs (side 4 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 343 lb  (12% used)
✓ Header over window (side 5) 2x6 21% used
2-ply 2x6 SPF #2, span 2.79 ft, w = 257 plf total / 168 plf live
Bending: M = wL²/8 = 3006 in·lb → fb = M/S = 199 psi ≤ F'b = 1308 psi  (15% used)
Shear: fv = 1.5V/A = 33 psi ≤ F'v = 155 psi  (21% used)
Deflection: 5wL⁴/384EI = 0.004" ≤ L/240 = 0.140"  (3% used)
✓ Studs (side 5 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 343 lb  (12% used)
✓ Studs (side 6 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 343 lb  (12% used)
✓ Header over window (side 7) 2x6 21% used
2-ply 2x6 SPF #2, span 2.79 ft, w = 257 plf total / 168 plf live
Bending: M = wL²/8 = 3006 in·lb → fb = M/S = 199 psi ≤ F'b = 1308 psi  (15% used)
Shear: fv = 1.5V/A = 33 psi ≤ F'v = 155 psi  (21% used)
Deflection: 5wL⁴/384EI = 0.004" ≤ L/240 = 0.140"  (3% used)
✓ Studs (side 7 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 343 lb  (12% used)
✓ Studs (side 8 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 343 lb  (12% used)
✓ Birdsmouth notch shear (hip rafters) 2x8 57% used
Heel cut 2-7/8" plumb leaves dn = 4.64" of the 7.25" depth over the bearing.
NDS 3.4.3.2 notched end: V'r = 2/3 · F'v · b · dn · (dn/d)² = 590 lb ≥ reaction 338 lb (57% used)
✓ Birdsmouth notch shear (rafters) 2x6 24% used
Heel cut 3/4" plumb leaves dn = 4.83" of the 5.5" depth over the bearing.
NDS 3.4.3.2 notched end: V'r = 2/3 · F'v · b · dn · (dn/d)² = 578 lb ≥ reaction 136 lb (24% used)

Roof: 10 psf dead + snow 0.7 × 30 = 21 psf. Floor: 40 psf live + 10 psf dead. 3 skids on 4" of compacted gravel, level within 1/4".

Questions

How much lumber does a 14′ Octagon Garden Room need?

73 2x4 × 8′, 20 2x6 × 8′, 8 2x6 × 10′, 16 2x8 × 10′, 1 6x6 × 8′, 11 PT 2x6 × 8′, 2 PT 2x6 × 10′, 1 PT 2x6 × 12′, 6 PT 2x6 × 14′, 2 PT 4x6 × 8′, 1 PT 4x6 × 16′. 9 3/4" T&G plywood subfloor, 4×8; 14 7/16" OSB wall sheathing, 4×8 (10% waste); 9 1/2" OSB roof sheathing, 4×8 (15% waste).

What size rafters does a 14′ Octagon Garden Room need?

2x6 at 16″ on center, using 28% of their capacity at 30 psf ground snow. The bending, shear and deflection numbers are in the proof section.

What size joists does a 14′ Octagon Garden Room need?

2x6 at 16″ on center, using 47% of capacity at 40 psf live load.

How tall is it?

13′ 3/4″ at the peak, measured from the ground.

Do I need a permit for a 14′ Octagon Garden Room?

It covers 162 sq ft. The model code (IRC R105.2) exempts one-story detached accessory buildings up to 200 sq ft, and many towns set the line at 120 sq ft. Call your building department before you dig.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

10′ Hexagon Garden Room87 sq ft · 120 pcs · 15 steps12′ Hexagon Garden Room124 sq ft · 143 pcs · 15 steps14′ Hexagon Garden Room170 sq ft · 148 pcs · 15 steps12′ Octagon Garden Room119 sq ft · 159 pcs · 17 steps