Design your own

12′ Hexagon Garden Room Plans

This 12′ hexagon garden room sits on pressure-treated skids on gravel, with 8′ walls, a 6/12 pyramid roof and a peak of 12′ 8-1/2″. The 38″-wide door opening gets a doubled header sized for the roof load above it. Rafters are 2x6 at 16″ on center. All 143 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 120 boards plus sheet goods and hardware.

Footprint6-sided, 6′ 11″ sides
Area124 sq ft
Height12′ 8-1/2″
Lumber143 pcs
Steps15
Checks15 pass

Open in the builderJump to the steps

3D model of the 12′ hexagon garden room framing

Shopping list

632x4 × 8′
272x6 × 8′
122x8 × 10′
16x6 × 8′
8PT 2x8 × 8′
1PT 2x8 × 10′
6PT 2x8 × 12′
2PT 4x6 × 8′
73/4" T&G plywood subfloor, 4×8
137/16" OSB wall sheathing, 4×8 (10% waste)
71/2" OSB roof sheathing, 4×8 (15% waste)
7bundles shingles (1.9 squares + 10%)
1rolls synthetic underlayment
36hurricane ties, rafter to plate

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A2PT 4x687-1/16"Skidsquare both ends
B5PT 2x8140-3/4"Floor joistsquare both ends
C1PT 2x8128-1/4"Floor joistends cut 60.0° off square
D1PT 2x8107-7/16"Floor joistends cut 60.0° off square
E6PT 2x883"Rim joistends cut to the 120.0° corner (30.0° mitre)
F1PT 2x872-13/16"Floor joistends cut 60.0° off square
G1PT 2x852"Floor joistends cut 60.0° off square
H1PT 2x817-3/8"Floor joistends cut 60.0° off square
J22x641"Header plysquare; two plies with a 1/2" plywood spacer
K32x492-5/8"Studsquare both ends
L22x492-5/8"King studsquare both ends
M12x483"Top plateends cut to the 120.0° corner (30.0° mitre)
N22x481"Jack studsquare both ends
P12x424-1/2"Bottom plateends cut to the 120.0° corner (30.0° mitre)
Q12x420-1/2"Bottom plateends cut to the 120.0° corner (30.0° mitre)
R22x46-1/8"Cripplesquare both ends
S62x492-5/8"Studsquare both ends
T12x483"Bottom plateends cut to the 120.0° corner (30.0° mitre)
U12x483"Top plateends cut to the 120.0° corner (30.0° mitre)
V22x633-1/2"Header plysquare; two plies with a 1/2" plywood spacer
W42x492-5/8"Studsquare both ends
X22x492-5/8"King studsquare both ends
Y12x483"Bottom plateends cut to the 120.0° corner (30.0° mitre)
Z12x483"Top plateends cut to the 120.0° corner (30.0° mitre)
AA22x471"Jack studsquare both ends
AB42x433"Cripplesquare both ends
AC12x430-1/2"Rough sillsquare both ends
AD22x416-1/8"Cripplesquare both ends
AE62x492-5/8"Studsquare both ends
AF12x483"Bottom plateends cut to the 120.0° corner (30.0° mitre)
AG12x483"Top plateends cut to the 120.0° corner (30.0° mitre)
AH22x633-1/2"Header plysquare; two plies with a 1/2" plywood spacer
AJ42x492-5/8"Studsquare both ends
AK22x492-5/8"King studsquare both ends
AL12x483"Bottom plateends cut to the 120.0° corner (30.0° mitre)
AM12x483"Top plateends cut to the 120.0° corner (30.0° mitre)
AN22x471"Jack studsquare both ends
AP42x433"Cripplesquare both ends
AQ12x430-1/2"Rough sillsquare both ends
AR22x416-1/8"Cripplesquare both ends
AS62x492-5/8"Studsquare both ends
AT12x483"Bottom plateends cut to the 120.0° corner (30.0° mitre)
AU12x483"Top plateends cut to the 120.0° corner (30.0° mitre)
AV62x483"Cap platelaps over the next wall at the corner
AW16x612-7/16"Hub block6-sided, 6-1/4" across the flats (glue up from 2x stock); top cut to a point at 6/12
AX122x8105-5/16"Hip rafter (2-ply)two identical plies nailed face to face; plumb cuts at 5.20/12 (23.4°); top edge dropped 3/8"; birdsmouth seat 4-15/16"
AY62x692-1/2"Centre raftertop: plumb cut 6/12 with 30.0° cheek cuts both sides (it sits between two hips); birdsmouth seat 1-1/2", heel 3/4"; tail plumb cut 12" past the wall
AZ122x663-5/8"Jack raftertop: plumb cut 6/12 plus a 30.0° cheek cut against the hip; birdsmouth seat 1-1/2", heel 3/4"; tail plumb cut 12" past the wall
BA122x632-11/16"Jack raftertop: plumb cut 6/12 plus a 30.0° cheek cut against the hip; birdsmouth seat 1-1/2", heel 3/4"; tail plumb cut 12" past the wall

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Lay the skids

    Lay the skids

    A ×2 4x6 87-1/16"

    • Compact 4" of gravel 2 ft past the footprint.
    • Lay A parallel, level within 1/4".

    rakelevel

  2. Step 2: Frame the floor

    Frame the floor

    B ×5 2x8 140-3/4"C ×1 2x8 128-1/4"D ×1 2x8 107-7/16"E ×6 2x8 83"F ×1 2x8 72-13/16"G ×1 2x8 52"H ×1 2x8 17-3/8"

    • Rims E around the outside, corners lapped as drawn.
    • Mark joists every 16" along the rims.
    • Joists B, C, D, F, G, H between the rims: 3 nails each end.
    • Measure both diagonals. Equal = square.

    sawhammersquaretape

  3. Step 3: Lay the subfloor

    Lay the subfloor

    • Long edge across the joists, rows staggered 4 ft.
    • Glue on every joist. Screws 6" on edges, 12" in the middle.

    drillsawchalk line

  4. Step 4: Build the side 1 wall

    Build the side 1 wall

    J ×2 2x6 41"K ×3 2x4 92-5/8"L ×2 2x4 92-5/8"M ×1 2x4 83"N ×2 2x4 81"P ×1 2x4 24-1/2"Q ×1 2x4 20-1/2"R ×2 2x4 6-1/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 77-7/16"
    • Frame the 38" × 82-1/2" door: kings, jacks, header.
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  5. Step 5: Build the side 2 wall

    Build the side 2 wall

    S ×6 2x4 92-5/8"T ×1 2x4 83"U ×1 2x4 83"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 77-7/16"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  6. Step 6: Build the side 3 wall

    Build the side 3 wall

    V ×2 2x6 33-1/2"W ×4 2x4 92-5/8"X ×2 2x4 92-5/8"Y ×1 2x4 83"Z ×1 2x4 83"AA ×2 2x4 71"AB ×4 2x4 33"AC ×1 2x4 30-1/2"AD ×2 2x4 16-1/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 77-7/16"
    • Frame the 30-1/2" × 36-1/2" window: kings, jacks, header.
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  7. Step 7: Build the side 4 wall

    Build the side 4 wall

    AE ×6 2x4 92-5/8"AF ×1 2x4 83"AG ×1 2x4 83"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 77-7/16"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  8. Step 8: Build the side 5 wall

    Build the side 5 wall

    AH ×2 2x6 33-1/2"AJ ×4 2x4 92-5/8"AK ×2 2x4 92-5/8"AL ×1 2x4 83"AM ×1 2x4 83"AN ×2 2x4 71"AP ×4 2x4 33"AQ ×1 2x4 30-1/2"AR ×2 2x4 16-1/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 77-7/16"
    • Frame the 30-1/2" × 36-1/2" window: kings, jacks, header.
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  9. Step 9: Build the side 6 wall

    Build the side 6 wall

    AS ×6 2x4 92-5/8"AT ×1 2x4 83"AU ×1 2x4 83"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 77-7/16"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  10. Step 10: Lap the cap plates

    Lap the cap plates

    AV ×6 2x4 83"

    • Cap plates overlap every corner. That ties the walls into one box.
    • Nails every 16", two at each lap.

    hammer

  11. Step 11: Make the hub

    Make the hub

    AW ×1 6x6 12-7/16"

    • Cut hub AW: 6-sided, 6-1/4" across the flats (glue up from 2x stock); top cut to a point at 6/12.
    • Hold it at the peak on a temporary centre post.

    sawclamps

  12. Step 12: Set the hip rafters

    Set the hip rafters

    AX ×12 2x8 105-5/16"

    • Cut ONE hip AX. Test it, then cut the rest.
    • Corner to hub. Set opposite pairs so the hub stays centred.

    speed squaresawdrill

  13. Step 13: Fill in the rafters

    Fill in the rafters

    AY ×6 2x6 92-1/2"AZ ×12 2x6 63-5/8"BA ×12 2x6 32-11/16"

    • Cut ONE pattern rafter. Check it in three places. Then cut the rest.
    • Jacks get a side (cheek) cut where they meet a hip.
    • Hurricane tie every rafter to the plate.

    speed squaresawdrill

  14. Step 14: Sheath the walls

    Sheath the walls

    • Sheets vertical, edges on studs, 1/8" gaps.
    • Nails 6" on edges, 12" in the middle. Cut out the openings after.

    sawnailerchalk line

  15. Step 15: Sheath the roof

    Sheath the roof

    • Long edge across the rafters, H-clips between, rows staggered.
    • Drip edge, underlayment, drip edge, shingles.

    sawnailer

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 156 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 156 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x8 86% used
2x8 SPF #2, span 11.69 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 13662 in·lb → fb = M/S = 1040 psi ≤ F'b = 1208 psi  (86% used)
Shear: fv = 1.5V/A = 54 psi ≤ F'v = 135 psi  (40% used)
Deflection: 5wL⁴/384EI = 0.336" ≤ L/360 = 0.390"  (86% used)
✓ Rafters 2x6 20% used
2x6 SPF #2, span 5.99 ft, w = 43 plf total / 28 plf live
Bending: M = wL²/8 = 2309 in·lb → fb = M/S = 305 psi ≤ F'b = 1504 psi  (20% used)
Shear: fv = 1.5V/A = 23 psi ≤ F'v = 155 psi  (15% used)
Deflection: 5wL⁴/384EI = 0.028" ≤ L/240 = 0.300"  (9% used)
Bending alone allows 2x4; stepped up to 2x6 so the birdsmouth notches pass shear.
✓ Header over door (side 1) 2x6 23% used
2-ply 2x6 SPF #2, span 3.42 ft, w = 225 plf total / 147 plf live
Bending: M = wL²/8 = 3939 in·lb → fb = M/S = 260 psi ≤ F'b = 1308 psi  (20% used)
Shear: fv = 1.5V/A = 35 psi ≤ F'v = 155 psi  (23% used)
Deflection: 5wL⁴/384EI = 0.008" ≤ L/240 = 0.171"  (5% used)
✓ Studs (side 1 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 300 lb  (11% used)
✓ Studs (side 2 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 300 lb  (11% used)
✓ Header over window (side 3) 2x6 18% used
2-ply 2x6 SPF #2, span 2.79 ft, w = 225 plf total / 147 plf live
Bending: M = wL²/8 = 2630 in·lb → fb = M/S = 174 psi ≤ F'b = 1308 psi  (13% used)
Shear: fv = 1.5V/A = 29 psi ≤ F'v = 155 psi  (18% used)
Deflection: 5wL⁴/384EI = 0.003" ≤ L/240 = 0.140"  (2% used)
✓ Studs (side 3 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 300 lb  (11% used)
✓ Studs (side 4 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 300 lb  (11% used)
✓ Header over window (side 5) 2x6 18% used
2-ply 2x6 SPF #2, span 2.79 ft, w = 225 plf total / 147 plf live
Bending: M = wL²/8 = 2630 in·lb → fb = M/S = 174 psi ≤ F'b = 1308 psi  (13% used)
Shear: fv = 1.5V/A = 29 psi ≤ F'v = 155 psi  (18% used)
Deflection: 5wL⁴/384EI = 0.003" ≤ L/240 = 0.140"  (2% used)
✓ Studs (side 5 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 300 lb  (11% used)
✓ Studs (side 6 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 300 lb  (11% used)
✓ Birdsmouth notch shear (hip rafters) 2x8 58% used
Heel cut 2-7/8" plumb leaves dn = 4.61" of the 7.25" depth over the bearing.
NDS 3.4.3.2 notched end: V'r = 2/3 · F'v · b · dn · (dn/d)² = 579 lb ≥ reaction 333 lb (58% used)
✓ Birdsmouth notch shear (rafters) 2x6 22% used
Heel cut 3/4" plumb leaves dn = 4.83" of the 5.5" depth over the bearing.
NDS 3.4.3.2 notched end: V'r = 2/3 · F'v · b · dn · (dn/d)² = 578 lb ≥ reaction 125 lb (22% used)

Roof: 10 psf dead + snow 0.7 × 30 = 21 psf. Floor: 40 psf live + 10 psf dead. 2 skids on 4" of compacted gravel, level within 1/4".

Questions

How much lumber does a 12′ Hexagon Garden Room need?

63 2x4 × 8′, 27 2x6 × 8′, 12 2x8 × 10′, 1 6x6 × 8′, 8 PT 2x8 × 8′, 1 PT 2x8 × 10′, 6 PT 2x8 × 12′, 2 PT 4x6 × 8′. 7 3/4" T&G plywood subfloor, 4×8; 13 7/16" OSB wall sheathing, 4×8 (10% waste); 7 1/2" OSB roof sheathing, 4×8 (15% waste).

What size rafters does a 12′ Hexagon Garden Room need?

2x6 at 16″ on center, using 20% of their capacity at 30 psf ground snow. The bending, shear and deflection numbers are in the proof section.

What size joists does a 12′ Hexagon Garden Room need?

2x8 at 16″ on center, using 86% of capacity at 40 psf live load.

How tall is it?

12′ 8-1/2″ at the peak, measured from the ground.

Do I need a permit for a 12′ Hexagon Garden Room?

It covers 124 sq ft. The model code (IRC R105.2) exempts one-story detached accessory buildings up to 200 sq ft, and many towns set the line at 120 sq ft. Call your building department before you dig.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

10′ Hexagon Garden Room87 sq ft · 120 pcs · 15 steps14′ Hexagon Garden Room170 sq ft · 148 pcs · 15 steps12′ Octagon Garden Room119 sq ft · 159 pcs · 17 steps14′ Octagon Garden Room162 sq ft · 162 pcs · 17 steps