Design your own

14′ Hexagon Garden Room Plans

This 14′ hexagon garden room sits on pressure-treated skids on gravel, with 8′ walls, a 6/12 pyramid roof and a peak of 13′ 2-13/16″. The 38″-wide door opening gets a doubled header sized for the roof load above it. Rafters are 2x8 at 16″ on center. All 148 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 126 boards plus sheet goods and hardware.

Footprint6-sided, 8′ 1″ sides
Area170 sq ft
Height13′ 2-13/16″
Lumber148 pcs
Steps15
Checks15 pass

Open in the builderJump to the steps

3D model of the 14′ hexagon garden room framing

Shopping list

122x10 × 12′
492x4 × 8′
172x4 × 10′
32x6 × 8′
182x8 × 8′
62x8 × 10′
16x6 × 8′
2PT 2x6 × 8′
8PT 2x6 × 10′
7PT 2x6 × 14′
2PT 4x6 × 10′
1PT 4x6 × 20′
103/4" T&G plywood subfloor, 4×8
147/16" OSB wall sheathing, 4×8 (10% waste)
91/2" OSB roof sheathing, 4×8 (15% waste)
9bundles shingles (2.5 squares + 10%)
1rolls synthetic underlayment
36hurricane ties, rafter to plate

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A1PT 4x6194"Skidsquare both ends
B2PT 4x6101-1/16"Skidsquare both ends
C5PT 2x6165"Floor joistsquare both ends
D1PT 2x6165"Floor joistends cut 60.0° off square
E1PT 2x6162-7/8"Floor joistends cut 60.0° off square
F1PT 2x6114-3/8"Floor joistends cut 60.0° off square
G1PT 2x6107-7/16"Floor joistends cut 60.0° off square
H6PT 2x697"Rim joistends cut to the 120.0° corner (30.0° mitre)
J1PT 2x658-15/16"Floor joistends cut 60.0° off square
K1PT 2x652"Floor joistends cut 60.0° off square
L22x641"Header plysquare; two plies with a 1/2" plywood spacer
M12x497"Top plateends cut to the 120.0° corner (30.0° mitre)
N42x492-5/8"Studsquare both ends
P22x492-5/8"King studsquare both ends
Q22x481"Jack studsquare both ends
R12x431-1/2"Bottom plateends cut to the 120.0° corner (30.0° mitre)
S12x427-1/2"Bottom plateends cut to the 120.0° corner (30.0° mitre)
T32x46-1/8"Cripplesquare both ends
U12x497"Bottom plateends cut to the 120.0° corner (30.0° mitre)
V12x497"Top plateends cut to the 120.0° corner (30.0° mitre)
W72x492-5/8"Studsquare both ends
X22x633-1/2"Header plysquare; two plies with a 1/2" plywood spacer
Y12x497"Bottom plateends cut to the 120.0° corner (30.0° mitre)
Z12x497"Top plateends cut to the 120.0° corner (30.0° mitre)
AA42x492-5/8"Studsquare both ends
AB22x492-5/8"King studsquare both ends
AC22x471"Jack studsquare both ends
AD32x433"Cripplesquare both ends
AE12x430-1/2"Rough sillsquare both ends
AF22x416-1/8"Cripplesquare both ends
AG12x497"Bottom plateends cut to the 120.0° corner (30.0° mitre)
AH12x497"Top plateends cut to the 120.0° corner (30.0° mitre)
AJ72x492-5/8"Studsquare both ends
AK22x633-1/2"Header plysquare; two plies with a 1/2" plywood spacer
AL12x497"Bottom plateends cut to the 120.0° corner (30.0° mitre)
AM12x497"Top plateends cut to the 120.0° corner (30.0° mitre)
AN42x492-5/8"Studsquare both ends
AP22x492-5/8"King studsquare both ends
AQ22x471"Jack studsquare both ends
AR32x433"Cripplesquare both ends
AS12x430-1/2"Rough sillsquare both ends
AT22x416-1/8"Cripplesquare both ends
AU12x497"Bottom plateends cut to the 120.0° corner (30.0° mitre)
AV12x497"Top plateends cut to the 120.0° corner (30.0° mitre)
AW72x492-5/8"Studsquare both ends
AX62x497"Cap platelaps over the next wall at the corner
AY16x614-5/8"Hub block6-sided, 6-1/4" across the flats (glue up from 2x stock); top cut to a point at 6/12
AZ122x10121-7/16"Hip rafter (2-ply)two identical plies nailed face to face; plumb cuts at 5.20/12 (23.4°); top edge dropped 3/8"; birdsmouth seat 4-15/16"
BA62x8106-15/16"Centre raftertop: plumb cut 6/12 with 30.0° cheek cuts both sides (it sits between two hips); birdsmouth seat 1-1/2", heel 3/4"; tail plumb cut 12" past the wall
BB122x878-1/16"Jack raftertop: plumb cut 6/12 plus a 30.0° cheek cut against the hip; birdsmouth seat 1-1/2", heel 3/4"; tail plumb cut 12" past the wall
BC122x847-1/16"Jack raftertop: plumb cut 6/12 plus a 30.0° cheek cut against the hip; birdsmouth seat 1-1/2", heel 3/4"; tail plumb cut 12" past the wall

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Lay the skids

    Lay the skids

    A ×1 4x6 194"B ×2 4x6 101-1/16"

    • Compact 4" of gravel 2 ft past the footprint.
    • Lay A, B parallel, level within 1/4".

    rakelevel

  2. Step 2: Frame the floor

    Frame the floor

    C ×5 2x6 165"D ×1 2x6 165"E ×1 2x6 162-7/8"F ×1 2x6 114-3/8"G ×1 2x6 107-7/16"H ×6 2x6 97"J ×1 2x6 58-15/16"K ×1 2x6 52"

    • Rims H around the outside, corners lapped as drawn.
    • Mark joists every 16" along the rims.
    • Joists C, D, E, F, G, J, K between the rims: 3 nails each end.
    • Measure both diagonals. Equal = square.

    sawhammersquaretape

  3. Step 3: Lay the subfloor

    Lay the subfloor

    • Long edge across the joists, rows staggered 4 ft.
    • Glue on every joist. Screws 6" on edges, 12" in the middle.

    drillsawchalk line

  4. Step 4: Build the side 1 wall

    Build the side 1 wall

    L ×2 2x6 41"M ×1 2x4 97"N ×4 2x4 92-5/8"P ×2 2x4 92-5/8"Q ×2 2x4 81"R ×1 2x4 31-1/2"S ×1 2x4 27-1/2"T ×3 2x4 6-1/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 91-7/16"
    • Frame the 38" × 82-1/2" door: kings, jacks, header.
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  5. Step 5: Build the side 2 wall

    Build the side 2 wall

    U ×1 2x4 97"V ×1 2x4 97"W ×7 2x4 92-5/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 91-7/16"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  6. Step 6: Build the side 3 wall

    Build the side 3 wall

    X ×2 2x6 33-1/2"Y ×1 2x4 97"Z ×1 2x4 97"AA ×4 2x4 92-5/8"AB ×2 2x4 92-5/8"AC ×2 2x4 71"AD ×3 2x4 33"AE ×1 2x4 30-1/2"AF ×2 2x4 16-1/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 91-7/16"
    • Frame the 30-1/2" × 36-1/2" window: kings, jacks, header.
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  7. Step 7: Build the side 4 wall

    Build the side 4 wall

    AG ×1 2x4 97"AH ×1 2x4 97"AJ ×7 2x4 92-5/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 91-7/16"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  8. Step 8: Build the side 5 wall

    Build the side 5 wall

    AK ×2 2x6 33-1/2"AL ×1 2x4 97"AM ×1 2x4 97"AN ×4 2x4 92-5/8"AP ×2 2x4 92-5/8"AQ ×2 2x4 71"AR ×3 2x4 33"AS ×1 2x4 30-1/2"AT ×2 2x4 16-1/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 91-7/16"
    • Frame the 30-1/2" × 36-1/2" window: kings, jacks, header.
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  9. Step 9: Build the side 6 wall

    Build the side 6 wall

    AU ×1 2x4 97"AV ×1 2x4 97"AW ×7 2x4 92-5/8"

    • Lay bottom and top plates side by side on the floor.
    • Mark stud left edges from the left end (outside view): -0" · 15-1/4" · 31-1/4" · 47-1/4" · 63-1/4" · 79-1/4" · 91-7/16"
    • Nail 2 × 16d through the plates into each stud end.
    • Equal diagonals, stand it up, plumb, brace.

    sawhammerlevelsquare

  10. Step 10: Lap the cap plates

    Lap the cap plates

    AX ×6 2x4 97"

    • Cap plates overlap every corner. That ties the walls into one box.
    • Nails every 16", two at each lap.

    hammer

  11. Step 11: Make the hub

    Make the hub

    AY ×1 6x6 14-5/8"

    • Cut hub AY: 6-sided, 6-1/4" across the flats (glue up from 2x stock); top cut to a point at 6/12.
    • Hold it at the peak on a temporary centre post.

    sawclamps

  12. Step 12: Set the hip rafters

    Set the hip rafters

    AZ ×12 2x10 121-7/16"

    • Cut ONE hip AZ. Test it, then cut the rest.
    • Corner to hub. Set opposite pairs so the hub stays centred.

    speed squaresawdrill

  13. Step 13: Fill in the rafters

    Fill in the rafters

    BA ×6 2x8 106-15/16"BB ×12 2x8 78-1/16"BC ×12 2x8 47-1/16"

    • Cut ONE pattern rafter. Check it in three places. Then cut the rest.
    • Jacks get a side (cheek) cut where they meet a hip.
    • Hurricane tie every rafter to the plate.

    speed squaresawdrill

  14. Step 14: Sheath the walls

    Sheath the walls

    • Sheets vertical, edges on studs, 1/8" gaps.
    • Nails 6" on edges, 12" in the middle. Cut out the openings after.

    sawnailerchalk line

  15. Step 15: Sheath the roof

    Sheath the roof

    • Long edge across the rafters, H-clips between, rows staggered.
    • Drip edge, underlayment, drip edge, shingles.

    sawnailer

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 164 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 164 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x6 47% used
2x6 SPF #2, span 6.85 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 4698 in·lb → fb = M/S = 621 psi ≤ F'b = 1308 psi  (47% used)
Shear: fv = 1.5V/A = 42 psi ≤ F'v = 135 psi  (31% used)
Deflection: 5wL⁴/384EI = 0.091" ≤ L/360 = 0.228"  (40% used)
✓ Rafters 2x8 17% used
2x8 SPF #2, span 7.00 ft, w = 43 plf total / 28 plf live
Bending: M = wL²/8 = 3154 in·lb → fb = M/S = 240 psi ≤ F'b = 1389 psi  (17% used)
Shear: fv = 1.5V/A = 21 psi ≤ F'v = 155 psi  (13% used)
Deflection: 5wL⁴/384EI = 0.023" ≤ L/240 = 0.350"  (6% used)
Bending alone allows 2x4; stepped up to 2x8 so the birdsmouth notches pass shear.
✓ Header over door (side 1) 2x6 26% used
2-ply 2x6 SPF #2, span 3.42 ft, w = 257 plf total / 168 plf live
Bending: M = wL²/8 = 4508 in·lb → fb = M/S = 298 psi ≤ F'b = 1308 psi  (23% used)
Shear: fv = 1.5V/A = 40 psi ≤ F'v = 155 psi  (26% used)
Deflection: 5wL⁴/384EI = 0.009" ≤ L/240 = 0.171"  (5% used)
✓ Studs (side 1 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 343 lb  (12% used)
✓ Studs (side 2 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 343 lb  (12% used)
✓ Header over window (side 3) 2x6 21% used
2-ply 2x6 SPF #2, span 2.79 ft, w = 257 plf total / 168 plf live
Bending: M = wL²/8 = 3010 in·lb → fb = M/S = 199 psi ≤ F'b = 1308 psi  (15% used)
Shear: fv = 1.5V/A = 33 psi ≤ F'v = 155 psi  (21% used)
Deflection: 5wL⁴/384EI = 0.004" ≤ L/240 = 0.140"  (3% used)
✓ Studs (side 3 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 343 lb  (12% used)
✓ Studs (side 4 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 343 lb  (12% used)
✓ Header over window (side 5) 2x6 21% used
2-ply 2x6 SPF #2, span 2.79 ft, w = 257 plf total / 168 plf live
Bending: M = wL²/8 = 3010 in·lb → fb = M/S = 199 psi ≤ F'b = 1308 psi  (15% used)
Shear: fv = 1.5V/A = 33 psi ≤ F'v = 155 psi  (21% used)
Deflection: 5wL⁴/384EI = 0.004" ≤ L/240 = 0.140"  (3% used)
✓ Studs (side 5 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 343 lb  (12% used)
✓ Studs (side 6 wall) 53% used
2x4 SPF #2, unbraced length 92.6" (le/d = 26.5 ≤ 50)
F*c = 1521 psi, FcE = 0.822·Emin/(le/d)² = 599 psi → Cp = 0.355
Capacity = Cp·F*c·A = 2831 lb ≥ load 343 lb  (12% used)
✓ Birdsmouth notch shear (hip rafters) 2x10 62% used
Heel cut 3-1/8" plumb leaves dn = 6.41" of the 9.25" depth over the bearing.
NDS 3.4.3.2 notched end: V'r = 2/3 · F'v · b · dn · (dn/d)² = 954 lb ≥ reaction 592 lb (62% used)
✓ Birdsmouth notch shear (rafters) 2x8 17% used
Heel cut 3/4" plumb leaves dn = 6.58" of the 7.25" depth over the bearing.
NDS 3.4.3.2 notched end: V'r = 2/3 · F'v · b · dn · (dn/d)² = 841 lb ≥ reaction 145 lb (17% used)

Roof: 10 psf dead + snow 0.7 × 30 = 21 psf. Floor: 40 psf live + 10 psf dead. 3 skids on 4" of compacted gravel, level within 1/4".

Questions

How much lumber does a 14′ Hexagon Garden Room need?

12 2x10 × 12′, 49 2x4 × 8′, 17 2x4 × 10′, 3 2x6 × 8′, 18 2x8 × 8′, 6 2x8 × 10′, 1 6x6 × 8′, 2 PT 2x6 × 8′, 8 PT 2x6 × 10′, 7 PT 2x6 × 14′, 2 PT 4x6 × 10′, 1 PT 4x6 × 20′. 10 3/4" T&G plywood subfloor, 4×8; 14 7/16" OSB wall sheathing, 4×8 (10% waste); 9 1/2" OSB roof sheathing, 4×8 (15% waste).

What size rafters does a 14′ Hexagon Garden Room need?

2x8 at 16″ on center, using 17% of their capacity at 30 psf ground snow. The bending, shear and deflection numbers are in the proof section.

What size joists does a 14′ Hexagon Garden Room need?

2x6 at 16″ on center, using 47% of capacity at 40 psf live load.

How tall is it?

13′ 2-13/16″ at the peak, measured from the ground.

Do I need a permit for a 14′ Hexagon Garden Room?

It covers 170 sq ft. The model code (IRC R105.2) exempts one-story detached accessory buildings up to 200 sq ft, and many towns set the line at 120 sq ft. Call your building department before you dig.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

10′ Hexagon Garden Room87 sq ft · 120 pcs · 15 steps12′ Hexagon Garden Room124 sq ft · 143 pcs · 15 steps12′ Octagon Garden Room119 sq ft · 159 pcs · 17 steps14′ Octagon Garden Room162 sq ft · 162 pcs · 17 steps