Design your own

10′ Octagon Deck Plans

This 8-sided, 4′ 1-1/2″ sides deck stands 30″ off the ground on posts on concrete footings. Joists are 2x6 at 16″ on center, carried by doubled 2x8 beams. All 47 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 44 boards plus sheet goods and hardware.

Footprint8-sided, 4′ 1-1/2″ sides
Area82 sq ft
Height2′ 6″
Lumber47 pcs
Steps5
Checks6 pass

Open in the builderJump to the steps

3D model of the 10′ octagon deck framing

Shopping list

13PT 2x6 × 8′
4PT 2x6 × 10′
4PT 2x8 × 8′
1PT 4x4 × 8′
8PT 5/4x6 × 8′
4PT 5/4x6 × 10′
10PT 5/4x6 × 12′
0.28cubic yards concrete (+10%)
4post bases + post caps
1boxes 2-1/2" deck screws (350/box)

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A4PT 4x416-1/4"Postsquare both ends
B4PT 2x862-3/16"Beam plysquare; 2 plies nailed together, 10d every 16" staggered
C3PT 2x6116-1/2"Floor joistsquare both ends
D1PT 2x6110-3/4"Floor joistends cut 45.0° off square
E1PT 2x693-3/4"Floor joistends cut 45.0° off square
F1PT 2x678-3/4"Floor joistends cut 45.0° off square
G1PT 2x661-3/4"Floor joistends cut 45.0° off square
H2PT 2x651-1/4"Floor joistends cut 45.0° off square
J8PT 2x650-3/8"Rim joistends cut to the 135.0° corner (22.5° mitre)
K2PT 5/4x6119-1/2"Deck boardends cut 45.0° off square
L8PT 5/4x6119-1/2"Deck boardsquare both ends
M1PT 5/4x6116-3/4"Deck boardends cut 45.0° off square
N1PT 5/4x6108-1/2"Deck boardends cut 45.0° off square
P1PT 5/4x6105-1/2"Deck boardends cut 45.0° off square
Q1PT 5/4x697-1/4"Deck boardends cut 45.0° off square
R1PT 5/4x694-1/4"Deck boardends cut 45.0° off square
S1PT 5/4x686"Deck boardends cut 45.0° off square
T1PT 5/4x683"Deck boardends cut 45.0° off square
U1PT 5/4x674-3/4"Deck boardends cut 45.0° off square
V1PT 5/4x671-3/4"Deck boardends cut 45.0° off square
W1PT 5/4x663-1/2"Deck boardends cut 45.0° off square
X1PT 5/4x660-1/2"Deck boardends cut 45.0° off square
Y1PT 5/4x652-1/4"Deck boardends cut 45.0° off square

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Dig and pour the footings

    Dig and pour the footings

    • Stake out 4 post spots exactly where the picture shows.
    • Dig each hole Ø20" wide, below your frost line.
    • Pour concrete. Set a post base in each one, all level with a string line.

    shovelstring linelevel

  2. Step 2: Stand the posts

    Stand the posts

    A ×4 4x4 16-1/4"

    • Cut posts A to the length in the box.
    • Fix each to its base. Plumb on two faces. Brace both ways.

    sawleveldrill

  3. Step 3: Set the beams

    Set the beams

    B ×4 2x8 62-3/16"

    • Nail each pair of B plies together, 10d nails every 16", staggered.
    • Crown up. Set on the posts and fix with post caps.

    sawhammerlevel

  4. Step 4: Frame the floor

    Frame the floor

    C ×3 2x6 116-1/2"D ×1 2x6 110-3/4"E ×1 2x6 93-3/4"F ×1 2x6 78-3/4"G ×1 2x6 61-3/4"H ×2 2x6 51-1/4"J ×8 2x6 50-3/8"

    • Rims J around the outside, corners lapped as drawn.
    • Mark joists every 16" along the rims.
    • Joists C, D, E, F, G, H between the rims: 3 nails each end.
    • Measure both diagonals. Equal = square.

    sawhammersquaretape

  5. Step 5: Lay the decking

    Lay the decking

    K ×2 5/4x6 119-1/2"L ×8 5/4x6 119-1/2"M ×1 5/4x6 116-3/4"N ×1 5/4x6 108-1/2"P ×1 5/4x6 105-1/2"Q ×1 5/4x6 97-1/4"R ×1 5/4x6 94-1/4"S ×1 5/4x6 86"T ×1 5/4x6 83"U ×1 5/4x6 74-3/4"V ×1 5/4x6 71-3/4"W ×1 5/4x6 63-1/2"X ×1 5/4x6 60-1/2"Y ×1 5/4x6 52-1/4"

    • Start at the front edge. 1/8" gap between boards (a 16d nail).
    • Two screws into every joist. Board ends only land on a joist.

    drillsawchalk line

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 47 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 51 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x6 60% used
2x6 SPF #2, span 7.71 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 5942 in·lb → fb = M/S = 786 psi ≤ F'b = 1308 psi  (60% used)
Shear: fv = 1.5V/A = 47 psi ≤ F'v = 135 psi  (35% used)
Deflection: 5wL⁴/384EI = 0.146" ≤ L/360 = 0.257"  (57% used)
✓ Deck beams (2-ply) 2x8 57% used
2-ply 2x8 SPF #2, span 4.89 ft, w = 435 plf total / 348 plf live
Bending: M = wL²/8 = 15621 in·lb → fb = M/S = 594 psi ≤ F'b = 1050 psi  (57% used)
Shear: fv = 1.5V/A = 73 psi ≤ F'v = 135 psi  (54% used)
Deflection: 5wL⁴/384EI = 0.034" ≤ L/360 = 0.163"  (21% used)
✓ Floor posts 4x4 13% used
4x4 SPF #2, height 1.35 ft, le/d = 4.6 ≤ 50
FcE = 19448 psi → Cp = 0.986 → capacity 15971 lb ≥ load 2129 lb (13% used)
✓ Footings 70% used
Load 2279 lb ÷ 1500 psf presumptive soil bearing = 219 in² needed
20" round footing = 314 in² (70% used). Bottom below your local frost depth.

Floor: 40 psf live + 10 psf dead. Footings bear on undisturbed soil below frost depth (1500 psf soil assumed). Post bases and post caps at every post.

Questions

How much lumber does a 10′ Octagon Deck need?

13 PT 2x6 × 8′, 4 PT 2x6 × 10′, 4 PT 2x8 × 8′, 1 PT 4x4 × 8′, 8 PT 5/4x6 × 8′, 4 PT 5/4x6 × 10′, 10 PT 5/4x6 × 12′. 0.28 cubic yards concrete (+10%); 4 post bases + post caps; 1 boxes 2-1/2" deck screws (350/box).

What size joists does a 10′ Octagon Deck need?

2x6 at 16″ on center, using 60% of capacity at 40 psf live load.

How big do the footings need to be?

20″ round, 4 of them, bearing below your local frost line. That assumes 1,500 psf soil.

Does a 10′ Octagon Deck need a railing?

Not by code at 30″; guards are required above 30″. You can add one in the builder.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

10×12 Deck120 sq ft · 57 pcs · 6 steps10×12 Deck120 sq ft · 171 pcs · 7 steps10×12 Deck120 sq ft · 175 pcs · 7 steps10×12 Ground-Level Deck120 sq ft · 38 pcs · 3 steps8′ Octagon Deck54 sq ft · 41 pcs · 5 steps12′ Octagon Deck119 sq ft · 52 pcs · 5 steps