Design your own

8′ Octagon Deck Plans

This 8-sided, 3′ 4″ sides deck stands 30″ off the ground on posts on concrete footings. Joists are 2x6 at 16″ on center, carried by doubled 2x8 beams. All 41 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 32 boards plus sheet goods and hardware.

Footprint8-sided, 3′ 4″ sides
Area54 sq ft
Height2′ 6″
Lumber41 pcs
Steps5
Checks6 pass

Open in the builderJump to the steps

3D model of the 8′ octagon deck framing

Shopping list

10PT 2x6 × 8′
4PT 2x8 × 8′
1PT 4x4 × 8′
8PT 5/4x6 × 8′
9PT 5/4x6 × 10′
0.18cubic yards concrete (+10%)
4post bases + post caps
1boxes 2-1/2" deck screws (350/box)

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A4PT 4x416-1/4"Postsquare both ends
B4PT 2x852-11/16"Beam plysquare; 2 plies nailed together, 10d every 16" staggered
C3PT 2x693-9/16"Floor joistsquare both ends
D1PT 2x670-3/8"Floor joistends cut 45.0° off square
E1PT 2x669-1/4"Floor joistends cut 45.0° off square
F2PT 2x641-3/4"Floor joistends cut 45.0° off square
G8PT 2x640-7/8"Rim joistends cut to the 135.0° corner (22.5° mitre)
H2PT 5/4x696-9/16"Deck boardends cut 45.0° off square
J6PT 5/4x696-9/16"Deck boardsquare both ends
K1PT 5/4x696"Deck boardends cut 45.0° off square
L1PT 5/4x686-7/8"Deck boardends cut 45.0° off square
M1PT 5/4x684-3/4"Deck boardends cut 45.0° off square
N1PT 5/4x675-5/8"Deck boardends cut 45.0° off square
P1PT 5/4x673-1/2"Deck boardends cut 45.0° off square
Q1PT 5/4x664-3/8"Deck boardends cut 45.0° off square
R1PT 5/4x662-1/4"Deck boardends cut 45.0° off square
S1PT 5/4x653-1/8"Deck boardends cut 45.0° off square
T1PT 5/4x651"Deck boardends cut 45.0° off square
U1PT 5/4x641-7/8"Deck boardends cut 45.0° off square

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Dig and pour the footings

    Dig and pour the footings

    • Stake out 4 post spots exactly where the picture shows.
    • Dig each hole Ø16" wide, below your frost line.
    • Pour concrete. Set a post base in each one, all level with a string line.

    shovelstring linelevel

  2. Step 2: Stand the posts

    Stand the posts

    A ×4 4x4 16-1/4"

    • Cut posts A to the length in the box.
    • Fix each to its base. Plumb on two faces. Brace both ways.

    sawleveldrill

  3. Step 3: Set the beams

    Set the beams

    B ×4 2x8 52-11/16"

    • Nail each pair of B plies together, 10d nails every 16", staggered.
    • Crown up. Set on the posts and fix with post caps.

    sawhammerlevel

  4. Step 4: Frame the floor

    Frame the floor

    C ×3 2x6 93-9/16"D ×1 2x6 70-3/8"E ×1 2x6 69-1/4"F ×2 2x6 41-3/4"G ×8 2x6 40-7/8"

    • Rims G around the outside, corners lapped as drawn.
    • Mark joists every 16" along the rims.
    • Joists C, D, E, F between the rims: 3 nails each end.
    • Measure both diagonals. Equal = square.

    sawhammersquaretape

  5. Step 5: Lay the decking

    Lay the decking

    H ×2 5/4x6 96-9/16"J ×6 5/4x6 96-9/16"K ×1 5/4x6 96"L ×1 5/4x6 86-7/8"M ×1 5/4x6 84-3/4"N ×1 5/4x6 75-5/8"P ×1 5/4x6 73-1/2"Q ×1 5/4x6 64-3/8"R ×1 5/4x6 62-1/4"S ×1 5/4x6 53-1/8"T ×1 5/4x6 51"U ×1 5/4x6 41-7/8"

    • Start at the front edge. 1/8" gap between boards (a 16d nail).
    • Two screws into every joist. Board ends only land on a joist.

    drillsawchalk line

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 41 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 45 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x6 34% used
2x6 SPF #2, span 5.80 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 3361 in·lb → fb = M/S = 444 psi ≤ F'b = 1308 psi  (34% used)
Shear: fv = 1.5V/A = 35 psi ≤ F'v = 135 psi  (26% used)
Deflection: 5wL⁴/384EI = 0.047" ≤ L/360 = 0.193"  (24% used)
✓ Deck beams (2-ply) 2x8 36% used
2-ply 2x8 SPF #2, span 4.10 ft, w = 340 plf total / 272 plf live
Bending: M = wL²/8 = 8565 in·lb → fb = M/S = 326 psi ≤ F'b = 1050 psi  (31% used)
Shear: fv = 1.5V/A = 48 psi ≤ F'v = 135 psi  (36% used)
Deflection: 5wL⁴/384EI = 0.013" ≤ L/360 = 0.137"  (9% used)
✓ Floor posts 4x4 9% used
4x4 SPF #2, height 1.35 ft, le/d = 4.6 ≤ 50
FcE = 19448 psi → Cp = 0.986 → capacity 15971 lb ≥ load 1393 lb (9% used)
✓ Footings 74% used
Load 1543 lb ÷ 1500 psf presumptive soil bearing = 148 in² needed
16" round footing = 201 in² (74% used). Bottom below your local frost depth.

Floor: 40 psf live + 10 psf dead. Footings bear on undisturbed soil below frost depth (1500 psf soil assumed). Post bases and post caps at every post.

Questions

How much lumber does a 8′ Octagon Deck need?

10 PT 2x6 × 8′, 4 PT 2x8 × 8′, 1 PT 4x4 × 8′, 8 PT 5/4x6 × 8′, 9 PT 5/4x6 × 10′. 0.18 cubic yards concrete (+10%); 4 post bases + post caps; 1 boxes 2-1/2" deck screws (350/box).

What size joists does a 8′ Octagon Deck need?

2x6 at 16″ on center, using 34% of capacity at 40 psf live load.

How big do the footings need to be?

16″ round, 4 of them, bearing below your local frost line. That assumes 1,500 psf soil.

Does a 8′ Octagon Deck need a railing?

Not by code at 30″; guards are required above 30″. You can add one in the builder.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

10×12 Deck120 sq ft · 57 pcs · 6 steps10×12 Deck120 sq ft · 171 pcs · 7 steps10×12 Deck120 sq ft · 175 pcs · 7 steps10×12 Ground-Level Deck120 sq ft · 38 pcs · 3 steps10′ Octagon Deck82 sq ft · 47 pcs · 5 steps12′ Octagon Deck119 sq ft · 52 pcs · 5 steps