Design your own

10×12 Deck Plans, 36″ High

This 10′ × 12′ deck stands 36″ off the ground on posts on concrete footings. Joists are 2x6 at 16″ on center, carried by doubled 2x8 beams. The stairs and the 36″ guard are drawn and checked. All 171 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 102 boards plus sheet goods and hardware.

Footprint10′ 0″ × 12′ 0″
Area120 sq ft
Height6′ 0″
Lumber171 pcs
Steps7
Checks9 pass

Open in the builderJump to the steps

3D model of the 10×12 deck framing

Shopping list

5PT 2x12 × 8′
26PT 2x2 × 8′
12PT 2x4 × 8′
8PT 2x6 × 8′
12PT 2x6 × 10′
4PT 2x6 × 12′
1PT 2x6 × 14′
4PT 2x8 × 12′
8PT 4x4 × 8′
22PT 5/4x6 × 14′
0.62cubic yards concrete (+10%)
6post bases + post caps
1boxes 2-1/2" deck screws (350/box)

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A6PT 4x422-1/4"Postsquare both ends
B4PT 2x8136"Beam plysquare; 2 plies nailed together, 10d every 16" staggered
C2PT 2x6142-1/2"Rim joistsquare ends; laps the next piece at the corner
D2PT 2x6118-1/2"Rim joistsquare ends; laps the next piece at the corner
E10PT 2x6117"Floor joistsquare both ends
F22PT 5/4x6144"Deck boardsquare both ends
G1PT 2x6144"Rail capflat on the post tops; mitred at corners
H2PT 2x6120"Rail capflat on the post tops; mitred at corners
J2PT 2x644-1/2"Rail capflat on the post tops; mitred at corners
K2PT 2x466-3/4"Bottom railsquare both ends
L2PT 2x466-3/4"Top railsquare both ends
M4PT 2x454-3/4"Bottom railsquare both ends
N4PT 2x454-3/4"Top railsquare both ends
P2PT 2x437-1/2"Bottom railsquare both ends
Q2PT 2x437-1/2"Top railsquare both ends
R13PT 4x441"Guard postsquare; through-bolt to the rim, two 1/2" bolts
S78PT 2x224"Balustersquare both ends
T4PT 2x1249-1/4"Stair stringer4 notches: rise 7-3/16", run 10-1/4"; plumb cut at the top, level cut at the bottom
U1PT 2x1248"Stair hanger boardsquare; bolt to the rim
V8PT 2x648"Stair treadsquare both ends

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Dig and pour the footings

    Dig and pour the footings

    • Stake out 6 post spots exactly where the picture shows.
    • Dig each hole Ø20" wide, below your frost line.
    • Pour concrete. Set a post base in each one, all level with a string line.

    shovelstring linelevel

  2. Step 2: Stand the posts

    Stand the posts

    A ×6 4x4 22-1/4"

    • Cut posts A to the length in the box.
    • Fix each to its base. Plumb on two faces. Brace both ways.

    sawleveldrill

  3. Step 3: Set the beams

    Set the beams

    B ×4 2x8 136"

    • Nail each pair of B plies together, 10d nails every 16", staggered.
    • Crown up. Set on the posts and fix with post caps.

    sawhammerlevel

  4. Step 4: Frame the floor

    Frame the floor

    C ×2 2x6 142-1/2"D ×2 2x6 118-1/2"E ×10 2x6 117"

    • Rims C, D around the outside, corners lapped as drawn.
    • Mark joists every 16" along the rims.
    • Joists E between the rims: 3 nails each end.
    • Measure both diagonals. Equal = square.

    sawhammersquaretape

  5. Step 5: Lay the decking

    Lay the decking

    F ×22 5/4x6 144"

    • Start at the front edge. 1/8" gap between boards (a 16d nail).
    • Two screws into every joist. Board ends only land on a joist.

    drillsawchalk line

  6. Step 6: Add the railing

    Add the railing

    G ×1 2x6 144"H ×2 2x6 120"J ×2 2x6 44-1/2"K ×2 2x4 66-3/4"L ×2 2x4 66-3/4"M ×4 2x4 54-3/4"N ×4 2x4 54-3/4"P ×2 2x4 37-1/2"Q ×2 2x4 37-1/2"R ×13 4x4 41"S ×78 2x2 24"

    • Posts first. Then bottom and top rails.
    • Balusters with a 3-7/8" spacer block between each.
    • Cap last.

    drillsawlevel

  7. Step 7: Build the stairs

    Build the stairs

    T ×4 2x12 49-1/4"U ×1 2x12 48"V ×8 2x6 48"

    • Bolt the hanger board to the rim.
    • Lay out ONE stringer with a framing square. Test it. Cut the rest.
    • Stringers on the pad. Two screws per tread board per stringer.

    framing squaresawdrill

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 171 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 178 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x6 61% used
2x6 SPF #2, span 7.75 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 6006 in·lb → fb = M/S = 794 psi ≤ F'b = 1308 psi  (61% used)
Shear: fv = 1.5V/A = 47 psi ≤ F'v = 135 psi  (35% used)
Deflection: 5wL⁴/384EI = 0.149" ≤ L/360 = 0.258"  (58% used)
✓ Deck beams (2-ply) 2x8 72% used
2-ply 2x8 SPF #2, span 5.52 ft, w = 438 plf total / 350 plf live
Bending: M = wL²/8 = 20002 in·lb → fb = M/S = 761 psi ≤ F'b = 1050 psi  (72% used)
Shear: fv = 1.5V/A = 83 psi ≤ F'v = 135 psi  (62% used)
Deflection: 5wL⁴/384EI = 0.055" ≤ L/360 = 0.184"  (30% used)
✓ Floor posts 4x4 15% used
4x4 SPF #2, height 1.85 ft, le/d = 6.4 ≤ 50
FcE = 10373 psi → Cp = 0.972 → capacity 15755 lb ≥ load 2415 lb (15% used)
✓ Footings 78% used
Load 2565 lb ÷ 1500 psf presumptive soil bearing = 246 in² needed
20" round footing = 314 in² (78% used). Bottom below your local frost depth.
✓ Guard geometry 90% used
36" guard height. Baluster gaps under 4", so a 4" ball cannot pass. Bottom gap 3-1/2".
Guard-post bolting follows the AWC DCA 6 detail; that connection is not calculated here.
✓ Stair geometry 93% used
5 equal risers of 7-3/16" (max 7-3/4"), 4 treads: 10-1/4" run + 1" nosing (min 10").
Notched 2x12 stringers keep 5-3/8" of wood under each notch (min 5").
✓ Stair stringers 19% used
2x12 (5.36" deep after notching) SPF #2, span 3.42 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 1167 in·lb → fb = M/S = 163 psi ≤ F'b = 875 psi  (19% used)
Shear: fv = 1.5V/A = 21 psi ≤ F'v = 135 psi  (16% used)
Deflection: 5wL⁴/384EI = 0.006" ≤ L/360 = 0.114"  (5% used)

Floor: 40 psf live + 10 psf dead. Footings bear on undisturbed soil below frost depth (1500 psf soil assumed). Post bases and post caps at every post.

Questions

How much lumber does a 10x12 Deck need?

5 PT 2x12 × 8′, 26 PT 2x2 × 8′, 12 PT 2x4 × 8′, 8 PT 2x6 × 8′, 12 PT 2x6 × 10′, 4 PT 2x6 × 12′, 1 PT 2x6 × 14′, 4 PT 2x8 × 12′, 8 PT 4x4 × 8′, 22 PT 5/4x6 × 14′. 0.62 cubic yards concrete (+10%); 6 post bases + post caps; 1 boxes 2-1/2" deck screws (350/box).

What size joists does a 10x12 Deck need?

2x6 at 16″ on center, using 61% of capacity at 40 psf live load.

How big do the footings need to be?

20″ round, 6 of them, bearing below your local frost line. That assumes 1,500 psf soil.

Does a 10x12 Deck need a railing?

Yes. Any deck surface more than 30″ above grade needs a guard at least 36″ high, and this plan includes one.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

10×12 Deck120 sq ft · 57 pcs · 6 steps10×12 Deck120 sq ft · 175 pcs · 7 steps10×12 Ground-Level Deck120 sq ft · 38 pcs · 3 steps8′ Octagon Deck54 sq ft · 41 pcs · 5 steps10′ Octagon Deck82 sq ft · 47 pcs · 5 steps12′ Octagon Deck119 sq ft · 52 pcs · 5 steps