Design your own

10×12 Ground-Level Deck Plans

This 10′ × 12′ deck stands at ground level on skids. Joists are 2x8 at 16″ on center, resting on the skids. All 38 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 38 boards plus sheet goods and hardware.

Footprint10′ 0″ × 12′ 0″
Area120 sq ft
Height1′ 1-3/4″
Lumber38 pcs
Steps3
Checks3 pass

Open in the builderJump to the steps

3D model of the 10×12 ground-level deck framing

Shopping list

12PT 2x8 × 10′
2PT 2x8 × 12′
2PT 4x6 × 14′
22PT 5/4x6 × 14′
1boxes 2-1/2" deck screws (350/box)

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A2PT 4x6144"Skidsquare both ends
B2PT 2x8142-1/2"Rim joistsquare ends; laps the next piece at the corner
C2PT 2x8118-1/2"Rim joistsquare ends; laps the next piece at the corner
D10PT 2x8117"Floor joistsquare both ends
E22PT 5/4x6144"Deck boardsquare both ends

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Lay the skids

    Lay the skids

    A ×2 4x6 144"

    • Compact 4" of gravel 2 ft past the footprint.
    • Lay A parallel, level within 1/4".

    rakelevel

  2. Step 2: Frame the floor

    Frame the floor

    B ×2 2x8 142-1/2"C ×2 2x8 118-1/2"D ×10 2x8 117"

    • Rims B, C around the outside, corners lapped as drawn.
    • Mark joists every 16" along the rims.
    • Joists D between the rims: 3 nails each end.
    • Measure both diagonals. Equal = square.

    sawhammersquaretape

  3. Step 3: Lay the decking

    Lay the decking

    E ×22 5/4x6 144"

    • Start at the front edge. 1/8" gap between boards (a 16d nail).
    • Two screws into every joist. Board ends only land on a joist.

    drillsawchalk line

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 38 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 38 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x8 59% used
2x8 SPF #2, span 9.71 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 9425 in·lb → fb = M/S = 717 psi ≤ F'b = 1208 psi  (59% used)
Shear: fv = 1.5V/A = 45 psi ≤ F'v = 135 psi  (33% used)
Deflection: 5wL⁴/384EI = 0.160" ≤ L/360 = 0.324"  (49% used)

Floor: 40 psf live + 10 psf dead. 2 skids on 4" of compacted gravel, level within 1/4".

Questions

How much lumber does a 10x12 Ground-Level Deck need?

12 PT 2x8 × 10′, 2 PT 2x8 × 12′, 2 PT 4x6 × 14′, 22 PT 5/4x6 × 14′. 1 boxes 2-1/2" deck screws (350/box).

What size joists does a 10x12 Ground-Level Deck need?

2x8 at 16″ on center, using 59% of capacity at 40 psf live load.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

10×12 Deck120 sq ft · 57 pcs · 6 steps10×12 Deck120 sq ft · 171 pcs · 7 steps10×12 Deck120 sq ft · 175 pcs · 7 steps8′ Octagon Deck54 sq ft · 41 pcs · 5 steps10′ Octagon Deck82 sq ft · 47 pcs · 5 steps12′ Octagon Deck119 sq ft · 52 pcs · 5 steps