Design your own

16×16 Deck Plans, 36″ High

This 16′ × 16′ deck stands 36″ off the ground on posts on concrete footings. Joists are 2x10 at 16″ on center, carried by doubled 2x10 beams. The stairs and the 36″ guard are drawn and checked. All 276 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 182 boards plus sheet goods and hardware.

Footprint16′ 0″ × 16′ 0″
Area256 sq ft
Height6′ 0″
Lumber276 pcs
Steps7
Checks9 pass

Open in the builderJump to the steps

3D model of the 16×16 deck framing

Shopping list

21PT 2x10 × 16′
5PT 2x12 × 8′
41PT 2x2 × 8′
22PT 2x4 × 8′
10PT 2x6 × 8′
3PT 2x6 × 20′
10PT 4x4 × 8′
35PT 5/4x6 × 8′
18PT 5/4x6 × 10′
17PT 5/4x6 × 12′
1.01cubic yards concrete (+10%)
8post bases + post caps
2boxes 2-1/2" deck screws (350/box)

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A8PT 4x416-1/2"Postsquare both ends
B4PT 2x10184"Beam plysquare; 2 plies nailed together, 10d every 16" staggered
C4PT 2x10190-1/2"Rim joistsquare ends; laps the next piece at the corner
D13PT 2x10189"Floor joistsquare both ends
E17PT 5/4x6127-15/16"Deck boardsquare both ends
F18PT 5/4x6111-15/16"Deck boardsquare both ends
G18PT 5/4x679-15/16"Deck boardsquare both ends
H17PT 5/4x663-15/16"Deck boardsquare both ends
J3PT 2x6192"Rail capflat on the post tops; mitred at corners
K2PT 2x668-1/2"Rail capflat on the post tops; mitred at corners
L2PT 2x461-1/2"Bottom railsquare both ends
M2PT 2x461-1/2"Top railsquare both ends
N9PT 2x459-5/16"Bottom railsquare both ends
P9PT 2x459-5/16"Top railsquare both ends
Q16PT 4x444-3/4"Guard postsquare; through-bolt to the rim, two 1/2" bolts
R121PT 2x224"Balustersquare both ends
S4PT 2x1249-1/4"Stair stringer4 notches: rise 7-3/16", run 10-1/4"; plumb cut at the top, level cut at the bottom
T1PT 2x1248"Stair hanger boardsquare; bolt to the rim
U8PT 2x648"Stair treadsquare both ends

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Dig and pour the footings

    Dig and pour the footings

    • Stake out 8 post spots exactly where the picture shows.
    • Dig each hole Ø24" wide, below your frost line.
    • Pour concrete. Set a post base in each one, all level with a string line.

    shovelstring linelevel

  2. Step 2: Stand the posts

    Stand the posts

    A ×8 4x4 16-1/2"

    • Cut posts A to the length in the box.
    • Fix each to its base. Plumb on two faces. Brace both ways.

    sawleveldrill

  3. Step 3: Set the beams

    Set the beams

    B ×4 2x10 184"

    • Nail each pair of B plies together, 10d nails every 16", staggered.
    • Crown up. Set on the posts and fix with post caps.

    sawhammerlevel

  4. Step 4: Frame the floor

    Frame the floor

    C ×4 2x10 190-1/2"D ×13 2x10 189"

    • Rims C around the outside, corners lapped as drawn.
    • Mark joists every 16" along the rims.
    • Joists D between the rims: 3 nails each end.
    • Measure both diagonals. Equal = square.

    sawhammersquaretape

  5. Step 5: Lay the decking

    Lay the decking

    E ×17 5/4x6 127-15/16"F ×18 5/4x6 111-15/16"G ×18 5/4x6 79-15/16"H ×17 5/4x6 63-15/16"

    • Start at the front edge. 1/8" gap between boards (a 16d nail).
    • Two screws into every joist. Board ends only land on a joist.

    drillsawchalk line

  6. Step 6: Add the railing

    Add the railing

    J ×3 2x6 192"K ×2 2x6 68-1/2"L ×2 2x4 61-1/2"M ×2 2x4 61-1/2"N ×9 2x4 59-5/16"P ×9 2x4 59-5/16"Q ×16 4x4 44-3/4"R ×121 2x2 24"

    • Posts first. Then bottom and top rails.
    • Balusters with a 3-7/8" spacer block between each.
    • Cap last.

    drillsawlevel

  7. Step 7: Build the stairs

    Build the stairs

    S ×4 2x12 49-1/4"T ×1 2x12 48"U ×8 2x6 48"

    • Bolt the hanger board to the rim.
    • Lay out ONE stringer with a framing square. Test it. Cut the rest.
    • Stringers on the pad. Two screws per tread board per stringer.

    framing squaresawdrill

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 276 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 285 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x10 80% used
2x10 SPF #2, span 13.75 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 18906 in·lb → fb = M/S = 884 psi ≤ F'b = 1107 psi  (80% used)
Shear: fv = 1.5V/A = 50 psi ≤ F'v = 135 psi  (37% used)
Deflection: 5wL⁴/384EI = 0.310" ≤ L/360 = 0.458"  (68% used)
✓ Deck beams (2-ply) 2x10 74% used
2-ply 2x10 SPF #2, span 5.01 ft, w = 738 plf total / 590 plf live
Bending: M = wL²/8 = 27810 in·lb → fb = M/S = 650 psi ≤ F'b = 963 psi  (68% used)
Shear: fv = 1.5V/A = 100 psi ≤ F'v = 135 psi  (74% used)
Deflection: 5wL⁴/384EI = 0.030" ≤ L/360 = 0.167"  (18% used)
✓ Floor posts 4x4 23% used
4x4 SPF #2, height 1.38 ft, le/d = 4.7 ≤ 50
FcE = 18863 psi → Cp = 0.985 → capacity 15964 lb ≥ load 3698 lb (23% used)
✓ Footings 82% used
Load 3848 lb ÷ 1500 psf presumptive soil bearing = 369 in² needed
24" round footing = 452 in² (82% used). Bottom below your local frost depth.
✓ Guard geometry 90% used
36" guard height. Baluster gaps under 4", so a 4" ball cannot pass. Bottom gap 3-1/2".
Guard-post bolting follows the AWC DCA 6 detail; that connection is not calculated here.
✓ Stair geometry 93% used
5 equal risers of 7-3/16" (max 7-3/4"), 4 treads: 10-1/4" run + 1" nosing (min 10").
Notched 2x12 stringers keep 5-3/8" of wood under each notch (min 5").
✓ Stair stringers 19% used
2x12 (5.36" deep after notching) SPF #2, span 3.42 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 1167 in·lb → fb = M/S = 163 psi ≤ F'b = 875 psi  (19% used)
Shear: fv = 1.5V/A = 21 psi ≤ F'v = 135 psi  (16% used)
Deflection: 5wL⁴/384EI = 0.006" ≤ L/360 = 0.114"  (5% used)

Floor: 40 psf live + 10 psf dead. Footings bear on undisturbed soil below frost depth (1500 psf soil assumed). Post bases and post caps at every post.

Questions

How much lumber does a 16x16 Deck need?

21 PT 2x10 × 16′, 5 PT 2x12 × 8′, 41 PT 2x2 × 8′, 22 PT 2x4 × 8′, 10 PT 2x6 × 8′, 3 PT 2x6 × 20′, 10 PT 4x4 × 8′, 35 PT 5/4x6 × 8′, 18 PT 5/4x6 × 10′, 17 PT 5/4x6 × 12′. 1.01 cubic yards concrete (+10%); 8 post bases + post caps; 2 boxes 2-1/2" deck screws (350/box).

What size joists does a 16x16 Deck need?

2x10 at 16″ on center, using 80% of capacity at 40 psf live load.

How big do the footings need to be?

24″ round, 8 of them, bearing below your local frost line. That assumes 1,500 psf soil.

Does a 16x16 Deck need a railing?

Yes. Any deck surface more than 30″ above grade needs a guard at least 36″ high, and this plan includes one.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

16×16 Deck256 sq ft · 110 pcs · 6 steps16×16 Deck256 sq ft · 280 pcs · 7 steps16×16 Ground-Level Deck256 sq ft · 90 pcs · 3 steps12×20 Deck240 sq ft · 95 pcs · 6 steps12×20 Deck240 sq ft · 259 pcs · 7 steps12×20 Deck240 sq ft · 263 pcs · 7 steps