16×16 Deck Plans, 48″ High
This 16′ × 16′ deck stands 48″ off the ground on posts on concrete footings. Joists are 2x10 at 16″ on center, carried by doubled 2x10 beams. The stairs and the 36″ guard are drawn and checked. All 280 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 187 boards plus sheet goods and hardware.

Shopping list
Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.
Parts and cut list
Cut every part, then pencil its letter on it. The steps call parts by letter.
| Part | Qty | Size | Length | Piece | How to cut |
|---|---|---|---|---|---|
| A | 8 | PT 4x4 | 28-1/2" | Post | square both ends |
| B | 4 | PT 2x10 | 184" | Beam ply | square; 2 plies nailed together, 10d every 16" staggered |
| C | 4 | PT 2x10 | 190-1/2" | Rim joist | square ends; laps the next piece at the corner |
| D | 13 | PT 2x10 | 189" | Floor joist | square both ends |
| E | 17 | PT 5/4x6 | 127-15/16" | Deck board | square both ends |
| F | 18 | PT 5/4x6 | 111-15/16" | Deck board | square both ends |
| G | 18 | PT 5/4x6 | 79-15/16" | Deck board | square both ends |
| H | 17 | PT 5/4x6 | 63-15/16" | Deck board | square both ends |
| J | 3 | PT 2x6 | 192" | Rail cap | flat on the post tops; mitred at corners |
| K | 2 | PT 2x6 | 68-1/2" | Rail cap | flat on the post tops; mitred at corners |
| L | 2 | PT 2x4 | 61-1/2" | Bottom rail | square both ends |
| M | 2 | PT 2x4 | 61-1/2" | Top rail | square both ends |
| N | 9 | PT 2x4 | 59-5/16" | Bottom rail | square both ends |
| P | 9 | PT 2x4 | 59-5/16" | Top rail | square both ends |
| Q | 16 | PT 4x4 | 44-3/4" | Guard post | square; through-bolt to the rim, two 1/2" bolts |
| R | 121 | PT 2x2 | 24" | Baluster | square both ends |
| S | 4 | PT 2x12 | 73-3/16" | Stair stringer | 6 notches: rise 6-7/8", run 10-1/4"; plumb cut at the top, level cut at the bottom |
| T | 1 | PT 2x12 | 48" | Stair hanger board | square; bolt to the rim |
| U | 12 | PT 2x6 | 48" | Stair tread | square both ends |
Step by step
New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

Dig and pour the footings
- Stake out 8 post spots exactly where the picture shows.
- Dig each hole Ø24" wide, below your frost line.
- Pour concrete. Set a post base in each one, all level with a string line.
shovelstring linelevel

Stand the posts
A ×8 4x4 28-1/2"
- Cut posts A to the length in the box.
- Fix each to its base. Plumb on two faces. Brace both ways.
sawleveldrill

Set the beams
B ×4 2x10 184"
- Nail each pair of B plies together, 10d nails every 16", staggered.
- Crown up. Set on the posts and fix with post caps.
sawhammerlevel

Frame the floor
C ×4 2x10 190-1/2"D ×13 2x10 189"
- Rims C around the outside, corners lapped as drawn.
- Mark joists every 16" along the rims.
- Joists D between the rims: 3 nails each end.
- Measure both diagonals. Equal = square.
sawhammersquaretape

Lay the decking
E ×17 5/4x6 127-15/16"F ×18 5/4x6 111-15/16"G ×18 5/4x6 79-15/16"H ×17 5/4x6 63-15/16"
- Start at the front edge. 1/8" gap between boards (a 16d nail).
- Two screws into every joist. Board ends only land on a joist.
drillsawchalk line

Add the railing
J ×3 2x6 192"K ×2 2x6 68-1/2"L ×2 2x4 61-1/2"M ×2 2x4 61-1/2"N ×9 2x4 59-5/16"P ×9 2x4 59-5/16"Q ×16 4x4 44-3/4"R ×121 2x2 24"
- Posts first. Then bottom and top rails.
- Balusters with a 3-7/8" spacer block between each.
- Cap last.
drillsawlevel

Build the stairs
S ×4 2x12 73-3/16"T ×1 2x12 48"U ×12 2x6 48"
- Bolt the hanger board to the rim.
- Lay out ONE stringer with a framing square. Test it. Cut the rest.
- Stringers on the pad. Two screws per tread board per stringer.
framing squaresawdrill
The proof
Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.
✓ No two pieces occupy the same space
All 280 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 289 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x10 80% used
2x10 SPF #2, span 13.75 ft, w = 67 plf total / 53 plf live Bending: M = wL²/8 = 18906 in·lb → fb = M/S = 884 psi ≤ F'b = 1107 psi (80% used) Shear: fv = 1.5V/A = 50 psi ≤ F'v = 135 psi (37% used) Deflection: 5wL⁴/384EI = 0.310" ≤ L/360 = 0.458" (68% used)
✓ Deck beams (2-ply) 2x10 74% used
2-ply 2x10 SPF #2, span 5.01 ft, w = 738 plf total / 590 plf live Bending: M = wL²/8 = 27810 in·lb → fb = M/S = 650 psi ≤ F'b = 963 psi (68% used) Shear: fv = 1.5V/A = 100 psi ≤ F'v = 135 psi (74% used) Deflection: 5wL⁴/384EI = 0.030" ≤ L/360 = 0.167" (18% used)
✓ Floor posts 4x4 24% used
4x4 SPF #2, height 2.38 ft, le/d = 8.1 ≤ 50 FcE = 6322 psi → Cp = 0.953 → capacity 15433 lb ≥ load 3698 lb (24% used)
✓ Footings 82% used
Load 3848 lb ÷ 1500 psf presumptive soil bearing = 369 in² needed 24" round footing = 452 in² (82% used). Bottom below your local frost depth.
✓ Guard geometry 90% used
36" guard height. Baluster gaps under 4", so a 4" ball cannot pass. Bottom gap 3-1/2". Guard-post bolting follows the AWC DCA 6 detail; that connection is not calculated here.
✓ Stair geometry 88% used
7 equal risers of 6-7/8" (max 7-3/4"), 6 treads: 10-1/4" run + 1" nosing (min 10"). Notched 2x12 stringers keep 5-9/16" of wood under each notch (min 5").
✓ Stair stringers 39% used
2x12 (5.55" deep after notching) SPF #2, span 5.13 ft, w = 67 plf total / 53 plf live Bending: M = wL²/8 = 2627 in·lb → fb = M/S = 341 psi ≤ F'b = 875 psi (39% used) Shear: fv = 1.5V/A = 31 psi ≤ F'v = 135 psi (23% used) Deflection: 5wL⁴/384EI = 0.028" ≤ L/360 = 0.171" (16% used)
Floor: 40 psf live + 10 psf dead. Footings bear on undisturbed soil below frost depth (1500 psf soil assumed). Post bases and post caps at every post.
Questions
How much lumber does a 16x16 Deck need?
21 PT 2x10 × 16′, 5 PT 2x12 × 8′, 41 PT 2x2 × 8′, 22 PT 2x4 × 8′, 14 PT 2x6 × 8′, 3 PT 2x6 × 20′, 11 PT 4x4 × 8′, 35 PT 5/4x6 × 8′, 18 PT 5/4x6 × 10′, 17 PT 5/4x6 × 12′. 1.01 cubic yards concrete (+10%); 8 post bases + post caps; 2 boxes 2-1/2" deck screws (350/box).
What size joists does a 16x16 Deck need?
2x10 at 16″ on center, using 80% of capacity at 40 psf live load.
How big do the footings need to be?
24″ round, 8 of them, bearing below your local frost line. That assumes 1,500 psf soil.
Does a 16x16 Deck need a railing?
Yes. Any deck surface more than 30″ above grade needs a guard at least 36″ high, and this plan includes one.
Can I change the size or add a door?
Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.
16×16 Deck
16×16 Deck
16×16 Ground-Level Deck
12×20 Deck
12×20 Deck
12×20 Deck