Design your own

10′ Hexagon Deck Plans

This 6-sided, 5′ 9-1/2″ sides deck stands 30″ off the ground on posts on concrete footings. Joists are 2x6 at 16″ on center, carried by doubled 2x8 beams. All 44 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 40 boards plus sheet goods and hardware.

Footprint6-sided, 5′ 9-1/2″ sides
Area87 sq ft
Height2′ 6″
Lumber44 pcs
Steps5
Checks6 pass

Open in the builderJump to the steps

3D model of the 10′ hexagon deck framing

Shopping list

8PT 2x6 × 8′
5PT 2x6 × 10′
4PT 2x8 × 8′
1PT 4x4 × 8′
8PT 5/4x6 × 8′
7PT 5/4x6 × 10′
7PT 5/4x6 × 12′
0.28cubic yards concrete (+10%)
4post bases + post caps
1boxes 2-1/2" deck screws (350/box)

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A4PT 4x416-1/4"Postsquare both ends
B4PT 2x874-1/8"Beam plysquare; 2 plies nailed together, 10d every 16" staggered
C4PT 2x6117-3/8"Floor joistsquare both ends
D1PT 2x6107-7/16"Floor joistends cut 60.0° off square
E1PT 2x690-1/8"Floor joistends cut 60.0° off square
F6PT 2x669-1/2"Rim joistends cut to the 120.0° corner (30.0° mitre)
G1PT 2x652"Floor joistends cut 60.0° off square
H1PT 2x634-11/16"Floor joistends cut 60.0° off square
J1PT 5/4x6139"Deck boardends cut 30.0° off square
K1PT 5/4x6137-1/16"Deck boardends cut 30.0° off square
L1PT 5/4x6134-5/16"Deck boardends cut 30.0° off square
M1PT 5/4x6130-9/16"Deck boardends cut 30.0° off square
N1PT 5/4x6127-13/16"Deck boardends cut 30.0° off square
P1PT 5/4x6124-1/16"Deck boardends cut 30.0° off square
Q1PT 5/4x6121-5/16"Deck boardends cut 30.0° off square
R1PT 5/4x6117-9/16"Deck boardends cut 30.0° off square
S1PT 5/4x6114-13/16"Deck boardends cut 30.0° off square
T1PT 5/4x6111-1/16"Deck boardends cut 30.0° off square
U1PT 5/4x6108-5/16"Deck boardends cut 30.0° off square
V1PT 5/4x6104-9/16"Deck boardends cut 30.0° off square
W1PT 5/4x6101-13/16"Deck boardends cut 30.0° off square
X1PT 5/4x698-1/16"Deck boardends cut 30.0° off square
Y1PT 5/4x695-5/16"Deck boardends cut 30.0° off square
Z1PT 5/4x691-9/16"Deck boardends cut 30.0° off square
AA1PT 5/4x688-13/16"Deck boardends cut 30.0° off square
AB1PT 5/4x685-1/16"Deck boardends cut 30.0° off square
AC1PT 5/4x682-3/8"Deck boardends cut 30.0° off square
AD1PT 5/4x678-5/8"Deck boardends cut 30.0° off square
AE1PT 5/4x675-7/8"Deck boardends cut 30.0° off square
AF1PT 5/4x672-1/8"Deck boardends cut 30.0° off square

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Dig and pour the footings

    Dig and pour the footings

    • Stake out 4 post spots exactly where the picture shows.
    • Dig each hole Ø20" wide, below your frost line.
    • Pour concrete. Set a post base in each one, all level with a string line.

    shovelstring linelevel

  2. Step 2: Stand the posts

    Stand the posts

    A ×4 4x4 16-1/4"

    • Cut posts A to the length in the box.
    • Fix each to its base. Plumb on two faces. Brace both ways.

    sawleveldrill

  3. Step 3: Set the beams

    Set the beams

    B ×4 2x8 74-1/8"

    • Nail each pair of B plies together, 10d nails every 16", staggered.
    • Crown up. Set on the posts and fix with post caps.

    sawhammerlevel

  4. Step 4: Frame the floor

    Frame the floor

    C ×4 2x6 117-3/8"D ×1 2x6 107-7/16"E ×1 2x6 90-1/8"F ×6 2x6 69-1/2"G ×1 2x6 52"H ×1 2x6 34-11/16"

    • Rims F around the outside, corners lapped as drawn.
    • Mark joists every 16" along the rims.
    • Joists C, D, E, G, H between the rims: 3 nails each end.
    • Measure both diagonals. Equal = square.

    sawhammersquaretape

  5. Step 5: Lay the decking

    Lay the decking

    J ×1 5/4x6 139"K ×1 5/4x6 137-1/16"L ×1 5/4x6 134-5/16"M ×1 5/4x6 130-9/16"N ×1 5/4x6 127-13/16"P ×1 5/4x6 124-1/16"Q ×1 5/4x6 121-5/16"R ×1 5/4x6 117-9/16"S ×1 5/4x6 114-13/16"T ×1 5/4x6 111-1/16"U ×1 5/4x6 108-5/16"V ×1 5/4x6 104-9/16"W ×1 5/4x6 101-13/16"X ×1 5/4x6 98-1/16"Y ×1 5/4x6 95-5/16"Z ×1 5/4x6 91-9/16"AA ×1 5/4x6 88-13/16"AB ×1 5/4x6 85-1/16"AC ×1 5/4x6 82-3/8"AD ×1 5/4x6 78-5/8"AE ×1 5/4x6 75-7/8"AF ×1 5/4x6 72-1/8"

    • Start at the front edge. 1/8" gap between boards (a 16d nail).
    • Two screws into every joist. Board ends only land on a joist.

    drillsawchalk line

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 44 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 48 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x6 61% used
2x6 SPF #2, span 7.78 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 6055 in·lb → fb = M/S = 801 psi ≤ F'b = 1308 psi  (61% used)
Shear: fv = 1.5V/A = 47 psi ≤ F'v = 135 psi  (35% used)
Deflection: 5wL⁴/384EI = 0.151" ≤ L/360 = 0.259"  (58% used)
✓ Deck beams (2-ply) 2x8 83% used
2-ply 2x8 SPF #2, span 5.88 ft, w = 439 plf total / 351 plf live
Bending: M = wL²/8 = 22809 in·lb → fb = M/S = 868 psi ≤ F'b = 1050 psi  (83% used)
Shear: fv = 1.5V/A = 89 psi ≤ F'v = 135 psi  (66% used)
Deflection: 5wL⁴/384EI = 0.071" ≤ L/360 = 0.196"  (36% used)
✓ Floor posts 4x4 16% used
4x4 SPF #2, height 1.35 ft, le/d = 4.6 ≤ 50
FcE = 19448 psi → Cp = 0.986 → capacity 15971 lb ≥ load 2584 lb (16% used)
✓ Footings 84% used
Load 2734 lb ÷ 1500 psf presumptive soil bearing = 262 in² needed
20" round footing = 314 in² (84% used). Bottom below your local frost depth.

Floor: 40 psf live + 10 psf dead. Footings bear on undisturbed soil below frost depth (1500 psf soil assumed). Post bases and post caps at every post.

Questions

How much lumber does a 10′ Hexagon Deck need?

8 PT 2x6 × 8′, 5 PT 2x6 × 10′, 4 PT 2x8 × 8′, 1 PT 4x4 × 8′, 8 PT 5/4x6 × 8′, 7 PT 5/4x6 × 10′, 7 PT 5/4x6 × 12′. 0.28 cubic yards concrete (+10%); 4 post bases + post caps; 1 boxes 2-1/2" deck screws (350/box).

What size joists does a 10′ Hexagon Deck need?

2x6 at 16″ on center, using 61% of capacity at 40 psf live load.

How big do the footings need to be?

20″ round, 4 of them, bearing below your local frost line. That assumes 1,500 psf soil.

Does a 10′ Hexagon Deck need a railing?

Not by code at 30″; guards are required above 30″. You can add one in the builder.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

10×12 Deck120 sq ft · 57 pcs · 6 steps10×12 Deck120 sq ft · 171 pcs · 7 steps10×12 Deck120 sq ft · 175 pcs · 7 steps10×12 Ground-Level Deck120 sq ft · 38 pcs · 3 steps8′ Octagon Deck54 sq ft · 41 pcs · 5 steps10′ Octagon Deck82 sq ft · 47 pcs · 5 steps