Design your own

16′ Octagon Deck Plans

This 8-sided, 6′ 7-1/2″ sides deck stands 30″ off the ground on posts on concrete footings. Joists are 2x10 at 16″ on center, carried by doubled 2x8 beams. All 82 pieces of lumber are lettered below with their lengths and cuts, and the shopping list comes to 77 boards plus sheet goods and hardware.

Footprint8-sided, 6′ 7-1/2″ sides
Area212 sq ft
Height2′ 6″
Lumber82 pcs
Steps5
Checks6 pass

Open in the builderJump to the steps

3D model of the 16′ octagon deck framing

Shopping list

10PT 2x10 × 8′
2PT 2x10 × 10′
2PT 2x10 × 12′
7PT 2x10 × 16′
4PT 2x8 × 8′
1PT 4x4 × 8′
19PT 5/4x6 × 8′
12PT 5/4x6 × 10′
12PT 5/4x6 × 12′
4PT 5/4x6 × 14′
4PT 5/4x6 × 16′
0.43cubic yards concrete (+10%)
6post bases + post caps
2boxes 2-1/2" deck screws (350/box)

Short pieces are cut from the offcuts of longer boards. Buy one spare of each size.

Parts and cut list

Cut every part, then pencil its letter on it. The steps call parts by letter.

PartQtySizeLengthPieceHow to cut
A6PT 4x412-1/2"Postsquare both ends
B4PT 2x892-3/16"Beam plysquare; 2 plies nailed together, 10d every 16" staggered
C5PT 2x10188-15/16"Floor joistsquare both ends
D1PT 2x10172-3/4"Floor joistends cut 45.0° off square
E1PT 2x10172-5/8"Floor joistends cut 45.0° off square
F1PT 2x10140-3/4"Floor joistends cut 45.0° off square
G1PT 2x10140-5/8"Floor joistends cut 45.0° off square
H1PT 2x10108-3/4"Floor joistends cut 45.0° off square
J1PT 2x10108-5/8"Floor joistends cut 45.0° off square
K2PT 2x1081-1/4"Floor joistends cut 45.0° off square
L8PT 2x1080-3/8"Rim joistends cut to the 135.0° corner (22.5° mitre)
M1PT 5/4x6182-1/8"Deck boardends cut 45.0° off square
N1PT 5/4x6180-1/2"Deck boardends cut 45.0° off square
P1PT 5/4x6170-7/8"Deck boardends cut 45.0° off square
Q1PT 5/4x6169-1/4"Deck boardends cut 45.0° off square
R1PT 5/4x6159-5/8"Deck boardends cut 45.0° off square
S1PT 5/4x6158"Deck boardends cut 45.0° off square
T1PT 5/4x6148-3/8"Deck boardends cut 45.0° off square
U1PT 5/4x6146-3/4"Deck boardends cut 45.0° off square
V1PT 5/4x6137-1/8"Deck boardends cut 45.0° off square
W1PT 5/4x6135-1/2"Deck boardends cut 45.0° off square
X7PT 5/4x6127-7/8"Deck boardsquare both ends
Y1PT 5/4x6127-7/8"Deck boardends cut 45.0° off square
Z1PT 5/4x6125-7/8"Deck boardends cut 45.0° off square
AA1PT 5/4x6124-1/4"Deck boardends cut 45.0° off square
AB1PT 5/4x6114-5/8"Deck boardends cut 45.0° off square
AC1PT 5/4x6113"Deck boardends cut 45.0° off square
AD7PT 5/4x6111-15/16"Deck boardsquare both ends
AE1PT 5/4x6111-7/8"Deck boardends cut 45.0° off square
AF1PT 5/4x6103-3/8"Deck boardends cut 45.0° off square
AG1PT 5/4x6101-3/4"Deck boardends cut 45.0° off square
AH1PT 5/4x692-1/8"Deck boardends cut 45.0° off square
AJ1PT 5/4x690-1/2"Deck boardends cut 45.0° off square
AK1PT 5/4x680-7/8"Deck boardends cut 45.0° off square
AL7PT 5/4x679-7/8"Deck boardsquare both ends
AM1PT 5/4x679-3/4"Deck boardends cut 45.0° off square
AN7PT 5/4x663-15/16"Deck boardsquare both ends
AP1PT 5/4x663-15/16"Deck boardends cut 45.0° off square

Step by step

New pieces are in colour with their letters. Work already done is greyed out. Open it in the builder to turn the model and print the manual.

  1. Step 1: Dig and pour the footings

    Dig and pour the footings

    • Stake out 6 post spots exactly where the picture shows.
    • Dig each hole Ø20" wide, below your frost line.
    • Pour concrete. Set a post base in each one, all level with a string line.

    shovelstring linelevel

  2. Step 2: Stand the posts

    Stand the posts

    A ×6 4x4 12-1/2"

    • Cut posts A to the length in the box.
    • Fix each to its base. Plumb on two faces. Brace both ways.

    sawleveldrill

  3. Step 3: Set the beams

    Set the beams

    B ×4 2x8 92-3/16"

    • Nail each pair of B plies together, 10d nails every 16", staggered.
    • Crown up. Set on the posts and fix with post caps.

    sawhammerlevel

  4. Step 4: Frame the floor

    Frame the floor

    C ×5 2x10 188-15/16"D ×1 2x10 172-3/4"E ×1 2x10 172-5/8"F ×1 2x10 140-3/4"G ×1 2x10 140-5/8"H ×1 2x10 108-3/4"J ×1 2x10 108-5/8"K ×2 2x10 81-1/4"L ×8 2x10 80-3/8"

    • Rims L around the outside, corners lapped as drawn.
    • Mark joists every 16" along the rims.
    • Joists C, D, E, F, G, H, J, K between the rims: 3 nails each end.
    • Measure both diagonals. Equal = square.

    sawhammersquaretape

  5. Step 5: Lay the decking

    Lay the decking

    M ×1 5/4x6 182-1/8"N ×1 5/4x6 180-1/2"P ×1 5/4x6 170-7/8"Q ×1 5/4x6 169-1/4"R ×1 5/4x6 159-5/8"S ×1 5/4x6 158"T ×1 5/4x6 148-3/8"U ×1 5/4x6 146-3/4"V ×1 5/4x6 137-1/8"W ×1 5/4x6 135-1/2"X ×7 5/4x6 127-7/8"Y ×1 5/4x6 127-7/8"Z ×1 5/4x6 125-7/8"AA ×1 5/4x6 124-1/4"AB ×1 5/4x6 114-5/8"AC ×1 5/4x6 113"AD ×7 5/4x6 111-15/16"AE ×1 5/4x6 111-7/8"AF ×1 5/4x6 103-3/8"AG ×1 5/4x6 101-3/4"AH ×1 5/4x6 92-1/8"AJ ×1 5/4x6 90-1/2"AK ×1 5/4x6 80-7/8"AL ×7 5/4x6 79-7/8"AM ×1 5/4x6 79-3/4"AN ×7 5/4x6 63-15/16"AP ×1 5/4x6 63-15/16"

    • Start at the front edge. 1/8" gap between boards (a 16d nail).
    • Two screws into every joist. Board ends only land on a joist.

    drillsawchalk line

The proof

Every member was sized by calculation, and the 3D model was tested piece against piece. These are the results for this plan.

✓ No two pieces occupy the same space
All 82 pieces tested pairwise as exact solids (mitres, birdsmouths, cheek cuts, notched stringers): no overlap deeper than 1/50".
✓ Every piece is connected to the ground
All 88 pieces trace a chain of contact down to the foundation.
✓ Floor joists 2x10 80% used
2x10 SPF #2, span 13.74 ft, w = 67 plf total / 53 plf live
Bending: M = wL²/8 = 18890 in·lb → fb = M/S = 883 psi ≤ F'b = 1107 psi  (80% used)
Shear: fv = 1.5V/A = 50 psi ≤ F'v = 135 psi  (37% used)
Deflection: 5wL⁴/384EI = 0.309" ≤ L/360 = 0.458"  (67% used)
✓ Deck beams (2-ply) 2x8 70% used
2-ply 2x8 SPF #2, span 3.70 ft, w = 737 plf total / 590 plf live
Bending: M = wL²/8 = 15100 in·lb → fb = M/S = 575 psi ≤ F'b = 1050 psi  (55% used)
Shear: fv = 1.5V/A = 94 psi ≤ F'v = 135 psi  (70% used)
Deflection: 5wL⁴/384EI = 0.019" ≤ L/360 = 0.123"  (15% used)
✓ Floor posts 4x4 17% used
4x4 SPF #2, height 1.04 ft, le/d = 3.6 ≤ 50
FcE = 32867 psi → Cp = 0.992 → capacity 16067 lb ≥ load 2724 lb (17% used)
✓ Footings 88% used
Load 2874 lb ÷ 1500 psf presumptive soil bearing = 276 in² needed
20" round footing = 314 in² (88% used). Bottom below your local frost depth.

Floor: 40 psf live + 10 psf dead. Footings bear on undisturbed soil below frost depth (1500 psf soil assumed). Post bases and post caps at every post.

Questions

How much lumber does a 16′ Octagon Deck need?

10 PT 2x10 × 8′, 2 PT 2x10 × 10′, 2 PT 2x10 × 12′, 7 PT 2x10 × 16′, 4 PT 2x8 × 8′, 1 PT 4x4 × 8′, 19 PT 5/4x6 × 8′, 12 PT 5/4x6 × 10′, 12 PT 5/4x6 × 12′, 4 PT 5/4x6 × 14′, 4 PT 5/4x6 × 16′. 0.43 cubic yards concrete (+10%); 6 post bases + post caps; 2 boxes 2-1/2" deck screws (350/box).

What size joists does a 16′ Octagon Deck need?

2x10 at 16″ on center, using 80% of capacity at 40 psf live load.

How big do the footings need to be?

20″ round, 6 of them, bearing below your local frost line. That assumes 1,500 psf soil.

Does a 16′ Octagon Deck need a railing?

Not by code at 30″; guards are required above 30″. You can add one in the builder.

Can I change the size or add a door?

Yes. Open the plan in the builder, change any number, and the cuts, shopping list and checks update instantly.

Related plans

10×12 Deck120 sq ft · 57 pcs · 6 steps10×12 Deck120 sq ft · 171 pcs · 7 steps10×12 Deck120 sq ft · 175 pcs · 7 steps10×12 Ground-Level Deck120 sq ft · 38 pcs · 3 steps8′ Octagon Deck54 sq ft · 41 pcs · 5 steps10′ Octagon Deck82 sq ft · 47 pcs · 5 steps